What is Federal Supply Class 5975?

FSC 5975 is the Federal Supply Class (formally known as NATO Supply Classification Class NSC 5975) in the USA for supply items codified in the category of Electrical Hardware and Supplies.

What is NATO Supply Classification Class 5975?

NSC 5975 is the NATO Supply Classification Class (also known as Federal Supply Class FSC 5975 in the USA) for supply items codified in the category of Electrical Hardware and Supplies.

Which Federal Supply Group is FSC 5975 in?

FSC 5975 is in Federal Supply Group (FSG) 59 which contains Electrical and Electronic Equipment Components.

Which NATO Supply Classification Group is NSC 5975 in?

NSC 5975is in NATO Supply Classification Group (NSG) 59 which contains Electrical and Electronic Equipment Components.

What is an Electrical Cable Protector?

An Electrical Cable Protector (PROTECTOR,ELECTRICAL CABLE) is an item designed to be interposed between a cable and its support or housing to prevent chafing caused by contraction and expansion due to changes in the ambient temperature or damage or injury from outside sources. Excludes such items as loom, cotton sleeving, rubber blankets, grade clamps and all types of conduit and INSULATION SLEEVING, ELECTRICAL.

What is a Ground Rod?

A Ground Rod (ROD,GROUND) is an item designed to be driven into the earth for the purpose of establishing electrical contact. One end is pointed or tapered to facilitate entrance into the earth. See also ROD SECTION, GROUND.

What is a Junction Box Assembly?

A Junction Box Assembly is two or more junction boxes on a common mounting or mounted on each other. Do not use for single junction boxes which are complex or unusual in construction, or for a junction box with an extension. See also TERMINAL BOX.

What is a Flexible Metal Conduit Assembly?

A Flexible Metal Conduit Assembly (CONDUIT ASSEMBLY,METAL,FLEXIBLE) is a specific length of CONDUIT, METAL, FLEXIBLE with permanently attached ferrule(s), coupling nut(s), elbow(s), or the like. Excludes detachable fittings such as tee(s), wye(s), or elbow(s). Also, excludes conduit like items that are designed for other than electrical applications. See also CASING (as modified).

What is a Fanning Strip?

A Fanning Strip is an item made of rigid or semirigid insulating material for spacing or separating wire(s) and/or cable(s). For items having terminals, see TERMINAL BOARD; and INSULATOR (as modified).

A Pothead is a form of terminator, usually used in power and telephone distribution, designed to be hermetically sealed to the cable(s) to exclude moisture. It may have terminals accessible for testing, or a junction block to facilitate the connecting of cable(s) and wire. See also SEALING FITTING, ELECTRICAL CONDUIT.

What is a Switch Terminal Cover?

A Switch Terminal Cover (COVER,SWITCH TERMINAL) is an item generally made of insulating material and used to protect switch terminals against damage, shorting and grounding. Excludes COVER, ELECTRICAL SWITCH; BASE, SWITCH and HOUSING, SENSITIVE SWITCH.

What is a Cable Terminal Chamber?

A Cable Terminal Chamber (CHAMBER,CABLE TERMINAL) is an item specifically designed to admit, protect and seal conductor groups or cables and also affords a method of conveniently distributing, terminating and interconnecting the leads.

What is a Stuffing Tube?

A Stuffing Tube is an item specifically designed to pass an electrical cable or tube through a continuous structure with provisions for packing so as to prevent the leakage of liquids and/or gases through the opening. May include packing nut(s), adapter(s), washer(s), gasket(s), bushing(s), packing(s), cap(s), and/or plug(s).

What is a Cord Assembly Fastener?

A Cord Assembly Fastener (FASTENER,CORD ASSEMBLY) is a fastener primarily designed to hold and secure a cord assembly so that pulling of the cord will not put a strain on the terminal connections.

What is an Electrical Grounding Plate?

An Electrical Grounding Plate (PLATE,ELECTRICAL GROUNDING) is a rigid or semirigid item of electrically conductive material whose thickness is small in comparsion to its length and width. It is designed to be used for electrical grounding, particularly in junction box and power outlet applications. Excludes TERMINAL STRIP, GROUNDING; CONTACT STRIP, RADIO FREQUENCY GROUNDING; and STRIP, ELECTRICAL GROUNDING.

What is a Cable Collar?

A Cable Collar (COLLAR,CABLE) is an item designed to be affixed around an electrical cable to limit the axial movement of the cable at the point where it passes through an opening. It has no facilities for retaining the cable to another object. Excludes BUSHING, STRAIN RELEIF, CABLE.

What is a Crossarm Brace?

A Crossarm Brace (BRACE,CROSSARM) is an item specifically designed to provide reinforcement for a crossarm when mounted on a pole.

What is a Cable Hanger?

A Cable Hanger (HANGER,CABLE) is a metallic or nonmetallic item of various shapes, designed to position, suspend, support and/or secure electrical cable(s) to utility poles, bulkheads, messenger wires or other supporting surfaces. It may be fastened to the structure by means of rod(s), bolts(s), screw(s) and the like. Excludes CLAMP (as modified); HANGER, WIRE STRAND; BRACKET PIPE; and SUPPORT, ELECTRICAL CABLE.

What is an Insulator Pin?

An Insulator Pin (PIN,INSULATOR) is an item designed to be inserted into a crossarm for the specific purpose of mounting pin type electrical insulators. Excludes BRACKET, INSULATOR.

What is a Stuffing Tube Plug?

A Stuffing Tube Plug (PLUG,STUFFING TUBE) is an item designed to be fitted into the body of a STUFFING TUBE in order to prevent the leakage of liquids and/or gases through the opening in the absence of the cable normally passing through the tube.

What is an Electrical Cable Support?

An Electrical Cable Support (SUPPORT,ELECTRICAL CABLE) is a collapsible framework specifically designed to be placed on the ground to hold electrical cable above the ground surface. Excludes BRACKET, PIPE.

What is an Electrical Conductor Bushing?

An Electrical Conductor Bushing (BUSHING,ELECTRICAL CONDUCTOR) is an item of metal and/or insulating material having a smooth interior with rounded edges to prevent damage to the insulation of the wire or cable emerging there-from, designed to fit through panel(s) or the wall of a JUNCTION BOX. It may be designed to snap into a knockout hole, or designed with an external thread and furnished with or without a locking nut. For items designed to couple conduit to JUNCTION BOX, see BOX CONNECTOR, ELECTRICAL. See also BUSHING, ELECTRICAL CONDUIT and BUSHING, NONMETALLIC. For items having hexagonal shoulders, see CHASE NIPPLE, CONDUIT.

What is an Insulator Bracket?

An Insulator Bracket (BRACKET,INSULATOR) is an item designed to be attached to a supporting surface for the specific purpose of positioning and sustaining an electrical insulator(s). Includes brackets specifically designed for transposing electrical lines.

What is a Cable Reinforcing Link?

A Cable Reinforcing Link (LINK,REINFORCING,CABLE) is an item fabricated from metal rod bent longitudinally into an oval shape, one end of which is intended to fit a messenger cable or guy wire and the opposite end formed with a mounting hole for a lag screw. This item is designed to relieve the strain where a messenger cable or wire is installed at an angle to a suspension clamp.

What is a Stuffing Tube Adapter?

A Stuffing Tube Adapter (ADAPTER,STUFFING TUBE) is a threaded or unthreaded item designed to mate with the mounting threads or mounting surfaces of a STUFFING TUBE, and to mount the STUFFING TUBE to a continuous structure (bulkhead or deck). The adapter may be recessed on the face to accommodate a gasket and/or washer.

What is a Junction Box?

A Junction Box is an enclosure of other than cast metal designed to house, mount, and protect, but does not include wiring connections or electrical device(s) such as terminals and/or terminal boards, switches, jacks, fuseholders, connectors, circuit breakers and the like. It is designed for and may include a cover and such accessories as mounting hardware, brackets, locks, clamps, mounts and conduit fittings. Excludes CONDUIT OUTLET; and CHAMBER, CABLE TERMINAL. For boxes which include electrical device(s) such as terminals and/or terminal boards, switches, fuseholders, jacks, connectors, circuit breakers and the like, or combinations thereof, see SWITCH BOX; FUZE BOX; JACK BOX; TERMINAL BOX; CIRCUIT BREAKER BOX; and DISTRIBUTION BOX. For boxes wired to provide the interconnecting facilities for a specific major group of electronic items outside of the box, see INTERCONNECTING BOX. See also INTERCONNECTING CABINET.

What is an Electrical Cable Nipple?

An Electrical Cable Nipple (CABLE NIPPLE,ELECTRICAL) is a preformed item having high electrical resistance designed for installation on end of cable or lead in order to cover the terminal or termination. It may partially cover the terminal of the item to which the cable or lead is attached. May also provide mechanical protection. Excludes INSULATION SLEEVING, ELECTRICAL.

What is an Electrical Equipment Cabinet?

An Electrical Equipment Cabinet (CABINET,ELECTRICAL EQUIPMENT) is an enclosure generally fabricated of sheet material designed to accommodate (but does not include) electrical/electronic equipment so that the equipment may be operated without removal. It may include wires, cables, terminal boards, connectors, etc., required for equipment operation. For items designed to accommodate equipment mounted on panels, see RACK, ELECTRICAL EQUIPMENT. See also CASE (2) (as modified). Excludes INTERCONNECTING BOX; INTERCONNECTING CABINET; JUNCTION BOX; and TERMINAL BOX.

What is an Electrical Equipment Rack?

An Electrical Equipment Rack (RACK,ELECTRICAL EQUIPMENT) is an open or inclosed frame structure designed to accommodate (but does not include) electrical/electronic equipment mounted on standard width panels so that the equipment may be operated after installation without being removed. It must have panel mounting rails that provide a uniform pattern of mounting holes that will accommodate various combinations of standard width panels. It may include wires, cables, terminal boards, connectors, and the like, required for equipment operation. See also MOUNTING BASE, ELECTRICAL EQUIPMENT; CABINET, ELECTRICAL EQUIPMENT; and CASE (2) (as modified). Excludes MAIN DISTRIBUTING FRAME, TELEPHONE and INTERMEDIATE DISTRIBUTING FRAME, TELEPHONE.

What is an Electrical Entrance Cap?

An Electrical Entrance Cap (ENTRANCE CAP,ELECTRICAL) is an item primarily designed to provide for the entrance of electrical wires into a building, structure, or inclosure and to facilitate their connection to feeders or service conductors. It consists of an insulating block and a metallic housing designed to hold the insulating block and to fit an electrical conduit, conduit fitting, or cable of a specified size. This item is primarily intended for use in exposed, wet, or damp locations and is installed so as to preclude the entrance of rain or debris into the conduit. See also CAP, ELECTRICAL.

What is an Electrical Conduit Adapter?

An Electrical Conduit Adapter (ADAPTER,ELECTRICAL CONDUIT) is an item designed to couple or join two different types or sizes of conduits, and/or to be inserted in the opening of a conduit outlet or box to accommodate a conduit of a larger or smaller size; or it may be designed with internal thread on one end for mating with an electrical connector and an external thread on the other end for mating with a conduit coupling nut; or to establish necessary mechanical accommodations between an electrical conduit, conduit assembly and an electrical connector. Excludes REDUCING WASHER, KNOCKOUT and BOX CONNECTOR, ELECTRICAL. See also ADAPTER, CABLE TO CONNECTOR; and CHASE NIPPLE, CONDUIT.

What is an Electrical Conduit Sealing Fitting?

An Electrical Conduit Sealing Fitting (SEALING FITTING,ELECTRICAL CONDUIT) is an item of metallic composition with a chamber for sealing compound and two hubs to accommodate electrical conduits of specified sizes. This item is designed with a filler hole and a removable screw plug to enable the pouring of sealing compound into the chamber for the purpose of preventing the passage of explosive gases through a conduit run. The item is primarily designed for use in hazardous locations and may be designed for vertical use, horizontal use, or both. For items which permit the connection or termination of wires, see POTHEAD. See also COUPLING, ELECTRICAL CONDUIT.

What is a Knockout Reducing Washer?

A Knockout Reducing Washer (REDUCING WASHER,KNOCKOUT) is an item consisting of a flat, cupped or embossed metallic disk with a centerhole to fit an electrical conduit of a specified size and which is specifically designed to reduce the knockout opening in a box, panel, or wireway for the convenience of terminating electrical conduit of smaller size than the knockout. Excludes ADAPTER, ELECTRICAL CONDUIT.

What is an Electrical Conduit Nipple?

An Electrical Conduit Nipple (NIPPLE,ELECTRICAL CONDUIT) is a nipple made of electrical conduit.

What is an Electrical Entrance Elbow?

An Electrical Entrance Elbow (ENTRANCE ELBOW,ELECTRICAL) is an item of metallic composition cast in the form of an elbow, which is primarily intended to provide for the angular entrance of wires into a building, structure, or enclosure. This item, specifically designed for installation in exposed locations, has two hubs of a specified size to fit the service entrance conduit and may have a third hub for a driven ground connection. It has a cover which makes it tamper-proof and weather-resistant. It may include facilities for pulling electrical conductors but does not have facilities for mounting wiring devices.

What is an Electrical Conduit Bushing?

An Electrical Conduit Bushing (BUSHING,ELECTRICAL CONDUIT) is an item of metal and/or insulating material having internal threads designed to fit over the end of electrical conduit and/or fittings to provide a smooth interior with a rounded edge to prevent damage to the insulation of the wire or cable emerging therefrom. It may be designed to fit over the end of thin wall conduit, and to be fitted with holding (staking) screws, or it may be provided with internal straight threads for attaching to thick wall electrical conduit or fittings. It may be fitted with a temporary knockout cap (bushcap), and grounding or bonding facilities. For externally threaded items, see BOX CONNECTOR, ELECTRICAL; BUSHING, ELECTRICAL CONDUCTOR; CHASE NIPPLE, CONDUIT and BUSHING, STRAIN RELIEF, CABLE. See also FERRULE, ELECTRICAL CONDUIT. Excludes plain sleeve bushings.

What is an Electrical Conduit Bondnut?

An Electrical Conduit Bondnut (BONDNUT,ELECTRICAL CONDUIT) is an item of metallic composition, with internal threads, designed to fit the external threads of an electrical conduit or fitting, and which, when installed, provides a method of tightening and locking the connection and completes a positive bond between the conduit and apparatus or fitting to which connected. The bonding or grounding action is accomplished by sharp beveled teeth or by a screw(s). See also LOCKNUT, ELECTRICAL CONDUIT and NUT, COUPLING, ELECTRICAL CONDUIT.

What is an Electrical Conduit Union?

An Electrical Conduit Union (UNION,ELECTRICAL CONDUIT) is an item comprising three members, so constructed that one of the members holds the remaining two in a fixed butted position; generally used to connect two conduits, conduit fittings, or a conduit and a conduit fitting in such a manner that they may be disconnected without disturbing the rest of the conduit line. See also COUPLING, ELECTRICAL CONDUIT.

What is an Electrical Conduit Elbow?

An Electrical Conduit Elbow (ELBOW,ELECTRICAL CONDUIT) is an item fabricated in the form of an elbow and having both ends threaded female, or with unthreaded connecting facilities on both ends, or connecting facilities on both ends, one of which is a male thread without boss or shoulder. If a locknut or bondnut is included, it shall not be considered as a thread boss or shoulder. It is primarily intended to connect conduit to conduit. It may have a removable cover to facilitate pulling wires, but does not include facilities for mounting wiring devices. For items having a removable cover to facilitate pulling wires and specifically designed for close installation in exposed outdoor locations and which may have facilities for an outside driven ground, see ENTRANCE ELBOW, ELECTRICAL. For items with one end having a male thread with a boss or shoulder, see BOX CONNECTOR, ELECTRICAL. For items having a removable screw cap for pulling wires, with the cap positioned 45 degrees from the connection facilities, see ENTRANCE ELBOW, ELECTRICAL. For items fabricated in the form of an elbow having both ends threaded male, see BEND, ELECTRICAL CONDUIT.

What is a Conduit Outlet?

A Conduit Outlet is an item designed to be used in a conduit system for the purpose of providing outlets or attachments for electrical wiring devices and/or designed to provide access and facilitate installment of wires. It may or may not include a cover(s). It does not include wiring devices. Excludes ENTRANCE ELBOW, ELECTRICAL. See also JUNCTION BOX.

What is an Electrical Conduit Bend?

An Electrical Conduit Bend (BEND,ELECTRICAL CONDUIT) is an item fabricated in the form of a curved section specifically designed to mechanically join a conduit or conduit fitting to another conduit or conduit fitting. Items of this type do not have a boss or hub at either end, nor do they have facilities for mounting wiring devices or pulling electrical conductors. See also ELBOW, ELECTRICAL CONDUIT and CONDUIT OUTLET.

What is an Electrical Wall Plate?

An Electrical Wall Plate (PLATE,WALL,ELECTRICAL) is an item designed to mount directly on a bracket or an electrical current carrying wiring device(s) such as switch(es) or outlet(s) (receptacle). The bracket(s) or electrical current carrying device is mounted in a JUNCTION BOX. For trade designated items designed to be attached directly on or through a bracket or electrical wiring device to a CONDUIT OUTLET, see COVER, CONDUIT OUTLET. For items designed for mounting directly on a JUNCTION BOX, see COVER, JUNCTION BOX.

What is an Interconnecting Box?

An Interconnecting Box is an inclosure which includes mounts and protects such items as switches, circuit breakers, jacks, fuseholders, connectors, terminals and/or terminal boards, resistors, capacitors, transformers, and the like. It is primarily designed to interconnect two or more electrical and/or electronic items, except primary power source(s) such as generator(s) and battery(ies). It may include a cover or door. For inclosures which connect one or more primary power source(s) to one or more electrical and/or electronic item(s), see DISTRIBUTION BOX. See also CIRCUIT BREAKER BOX; TERMINAL BOX and INTERCONNECTING CABINET.

A Pole Step (STEP,POLE) is an item designed to be used as a foot rest in ascending and descending utility poles, when attached thereto.

What is an Interior Cable Rack?

An Interior Cable Rack (RACK,CABLE,INTERIOR) is an open frame structure primarily designed to support electrical cables in buildings and shelters. Its purpose is to provide, by itself or by joining to similar structures, a path or runway for cable which may connect two or more pieces of electrical equipment. It does not include items designed to hold a single cable. See also RACK, CABLE, UNDERGROUND; and HANGER, CABLE.

What is an Electrical Conduit Ferrule?

An Electrical Conduit Ferrule (FERRULE,ELECTRICAL CONDUIT) is an item usually of one piece construction, but which may be comprised of more than one piece, designed to be affixed permanently or temporarily to the end of an electrical conduit to form an end fitting. Unflanged items form a permanent end fitting which affords mechanical protection to emerging conductors. Flanged items are used with another fitting normally a conduit coupling nut, to make the conduit adaptable for connection to an electrical connector, junction box or other conduit accessory or fitting. Excludes RING, ELECTRICAL BONDING; BUSHING, ELECTRICAL CONDUIT; and BUSHING, PLAIN SLEEVE. See also FERRULE-NUT COUPLING, ELECTRICAL CONDUIT.

What is an Underground Cable Rack Hook?

An Underground Cable Rack Hook (HOOK,UNDERGROUND CABLE RACK) is a rigid item designed to be perpendicularly attached to an underground cable rack to be used as the supporting arm for cables. May include insulators.

What is an Electrical Conduit End Seal Disk?

An Electrical Conduit End Seal Disk (DISK,END SEAL,ELECTRICAL CONDUIT) is a flat circular item fitted on the end of an electrical conduit in order to close the end to prevent the entrance of water or refuse, prior to installation of the wires, during shipment and/or construction. The item may be held in place by means of a conduit bushing and may be easily removed to permit installation of the wires.

What is a Cable Spacer?

A Cable Spacer (SPACER,CABLE) is an item constructed specifically to provide a separation between lashed lead covered cable and messenger strand for the prevention of injury to sheath of cable.

What is an Electrical Box Connector?

An Electrical Box Connector (BOX CONNECTOR,ELECTRICAL) is an item designed to mechanically connect in a straight line or an angle electrical conduit, conduit assemblies, wire, wireway, cable, or cable assemblies to a point of termination, such as a junction box, conduit outlet, or the like. The termination end must have an external thread with a boss or shoulder and may be furnished with a locknut or bondnut; or, must have internal thread with which is furnished an externally threaded hub with a wrenching feature; or be of a snap-in type that may be installed from either inside or outside the box and secured with a captive screw. It is not intended to join conduit to conduit. For angle type items having a male thread without a boss or shoulder, see ELBOW, ELECTRICAL CONDUIT. Does not include facilities to mount wiring devices. Excludes CHASE NIPPLE, CONDUIT.

What is an Electrical Conduit Coupling?

An Electrical Conduit Coupling (COUPLING,ELECTRICAL CONDUIT) is an item specifically designed and constructed to mechanically connect in a straight line two sections of electrical conduit or like fabrication and of the same size. For three-piece items which may be disassembled without disturbing the rest of the conduit line, see UNION, ELECTRICAL CONDUIT. See also ADAPTER, ELECTRICAL CONDUIT; POTHEAD; and SEALING FITTING, ELECTRICAL CONDUIT.

Electrical Hardware and Supplies - United States (US)

Federal Supply Class (FSC): 5975

NATO Supply Classification Class (NSC): 5975

Federal Supply Group (FSG): 59 Electrical and Electronic Equipment Components

NATO Supply Classification Group (NSG): 59 Electrical and Electronic Equipment Components

Items Managed by United States (US) - NCB is 00 to 09

Page 169 of 176

NSN Format for Electrical Hardware and Supplies
Codified by United States

59	75	01	XXX
Group FSG	Class	NCB	Identifier
FSC Federal Supply Class		NIIN
NSN

NATO Supply Class 5975 is a classification within NATO Supply Group 59, which is dedicated to Electrical and Electronic Equipment Components.

NATO Supply Class 5975 specifically focuses on Electrical Hardware and Supplies. This class includes a wide range of items such as electrical connectors, terminals, switches, circuit breakers, fuses, relays, cables, wires, and other related electrical components and accessories.

The purpose of this classification is to provide a standardized system for categorizing and organizing electrical hardware and supplies used in military and defense applications. By using this classification system, NATO member countries can easily identify, procure, and maintain the necessary electrical components for their equipment and systems.

It is important to note that the NATO Supply Classification (NSC) system is used primarily by NATO member countries for logistical and supply chain management purposes. It helps ensure interoperability and compatibility among different military forces by providing a common language for identifying and categorizing various items.

If you are working on a document related to electrical hardware and supplies in the context of NATO Supply Class 5975, you may want to include specific details about the types of components and their applications within military and defense systems. Additionally, you can mention the importance of adhering to the NATO Supply Classification system for efficient procurement and maintenance processes.

FSC 5975 Electrical Hardware and Supplies - United States (US)

Includes Conduit; Raceways; Face Plates; Condulets; Outlet and Junction Boxes; Pole Line Hardware, not elsewhere classifiable.

Note-Mounting hardware, included in classes of this group, includes such specially designed items as brackets, holders, retainers, etc. Excluded from classes in this group are such hardware items as screws (Class 5305), bolts (Class 5306), studs (Class 5307), washers (Class 5310), rivets (Class 5320), and other common items indexed to specific classes, other than in Group 59. The FSC indexes and structure will govern the classification of items used on or with mounting hardware cited above.

Frequently Asked Questions(FAQ) for Federal Supply Class 5975

What is Federal Supply Class 5975?: FSC 5975 is the Federal Supply Class (formally known as NATO Supply Classification Class NSC 5975) in the USA for supply items codified in the category of Electrical Hardware and Supplies.
What is NATO Supply Classification Class 5975?: NSC 5975 is the NATO Supply Classification Class (also known as Federal Supply Class FSC 5975 in the USA) for supply items codified in the category of Electrical Hardware and Supplies.
Which Federal Supply Group is FSC 5975 in?: FSC 5975 is in Federal Supply Group (FSG) 59 which contains Electrical and Electronic Equipment Components.
Which NATO Supply Classification Group is NSC 5975 in?: NSC 5975 is in NATO Supply Classification Group (NSG) 59 which contains Electrical and Electronic Equipment Components.

Supply Items Included in Federal Supply Class 5975

What is an Electrical Cable Protector? 768 Items: An Electrical Cable Protector (PROTECTOR,ELECTRICAL CABLE) is an item designed to be interposed between a cable and its support or housing to prevent chafing caused by contraction and expansion due to changes in the ambient temperature or damage or injury from outside sources. Excludes such items as loom, cotton sleeving, rubber blankets, grade clamps and all types of conduit and INSULATION SLEEVING, ELECTRICAL.
What is a Ground Rod? 262 Items: A Ground Rod (ROD,GROUND) is an item designed to be driven into the earth for the purpose of establishing electrical contact. One end is pointed or tapered to facilitate entrance into the earth. See also ROD SECTION, GROUND.
What is a Junction Box Assembly? 258 Items: A Junction Box Assembly is two or more junction boxes on a common mounting or mounted on each other. Do not use for single junction boxes which are complex or unusual in construction, or for a junction box with an extension. See also TERMINAL BOX.
What is a Flexible Metal Conduit Assembly? 1671 Items: A Flexible Metal Conduit Assembly (CONDUIT ASSEMBLY,METAL,FLEXIBLE) is a specific length of CONDUIT, METAL, FLEXIBLE with permanently attached ferrule(s), coupling nut(s), elbow(s), or the like. Excludes detachable fittings such as tee(s), wye(s), or elbow(s). Also, excludes conduit like items that are designed for other than electrical applications. See also CASING (as modified).
What is a Fanning Strip? 139 Items: A Fanning Strip is an item made of rigid or semirigid insulating material for spacing or separating wire(s) and/or cable(s). For items having terminals, see TERMINAL BOARD; and INSULATOR (as modified).
What is a Pothead? 13 Items: A Pothead is a form of terminator, usually used in power and telephone distribution, designed to be hermetically sealed to the cable(s) to exclude moisture. It may have terminals accessible for testing, or a junction block to facilitate the connecting of cable(s) and wire. See also SEALING FITTING, ELECTRICAL CONDUIT.
Cover,Interconnecting Box 59 Items
What is a Switch Terminal Cover? 107 Items: A Switch Terminal Cover (COVER,SWITCH TERMINAL) is an item generally made of insulating material and used to protect switch terminals against damage, shorting and grounding. Excludes COVER, ELECTRICAL SWITCH; BASE, SWITCH and HOUSING, SENSITIVE SWITCH.
What is a Cable Terminal Chamber? 141 Items: A Cable Terminal Chamber (CHAMBER,CABLE TERMINAL) is an item specifically designed to admit, protect and seal conductor groups or cables and also affords a method of conveniently distributing, terminating and interconnecting the leads.
What is a Stuffing Tube? 1137 Items: A Stuffing Tube is an item specifically designed to pass an electrical cable or tube through a continuous structure with provisions for packing so as to prevent the leakage of liquids and/or gases through the opening. May include packing nut(s), adapter(s), washer(s), gasket(s), bushing(s), packing(s), cap(s), and/or plug(s).
What is a Cord Assembly Fastener? 28 Items: A Cord Assembly Fastener (FASTENER,CORD ASSEMBLY) is a fastener primarily designed to hold and secure a cord assembly so that pulling of the cord will not put a strain on the terminal connections.
What is an Electrical Grounding Plate? 501 Items: An Electrical Grounding Plate (PLATE,ELECTRICAL GROUNDING) is a rigid or semirigid item of electrically conductive material whose thickness is small in comparsion to its length and width. It is designed to be used for electrical grounding, particularly in junction box and power outlet applications. Excludes TERMINAL STRIP, GROUNDING; CONTACT STRIP, RADIO FREQUENCY GROUNDING; and STRIP, ELECTRICAL GROUNDING.
What is a Cable Collar? 124 Items: A Cable Collar (COLLAR,CABLE) is an item designed to be affixed around an electrical cable to limit the axial movement of the cable at the point where it passes through an opening. It has no facilities for retaining the cable to another object. Excludes BUSHING, STRAIN RELEIF, CABLE.
Base,Chassis 324 Items
What is a Crossarm Brace? 31 Items: A Crossarm Brace (BRACE,CROSSARM) is an item specifically designed to provide reinforcement for a crossarm when mounted on a pole.
What is a Cable Hanger? 814 Items: A Cable Hanger (HANGER,CABLE) is a metallic or nonmetallic item of various shapes, designed to position, suspend, support and/or secure electrical cable(s) to utility poles, bulkheads, messenger wires or other supporting surfaces. It may be fastened to the structure by means of rod(s), bolts(s), screw(s) and the like. Excludes CLAMP (as modified); HANGER, WIRE STRAND; BRACKET PIPE; and SUPPORT, ELECTRICAL CABLE.
What is an Insulator Pin? 55 Items: An Insulator Pin (PIN,INSULATOR) is an item designed to be inserted into a crossarm for the specific purpose of mounting pin type electrical insulators. Excludes BRACKET, INSULATOR.
What is a Stuffing Tube Plug? 53 Items: A Stuffing Tube Plug (PLUG,STUFFING TUBE) is an item designed to be fitted into the body of a STUFFING TUBE in order to prevent the leakage of liquids and/or gases through the opening in the absence of the cable normally passing through the tube.
What is an Electrical Cable Support? 74 Items: An Electrical Cable Support (SUPPORT,ELECTRICAL CABLE) is a collapsible framework specifically designed to be placed on the ground to hold electrical cable above the ground surface. Excludes BRACKET, PIPE.
What is an Electrical Conductor Bushing? 421 Items: An Electrical Conductor Bushing (BUSHING,ELECTRICAL CONDUCTOR) is an item of metal and/or insulating material having a smooth interior with rounded edges to prevent damage to the insulation of the wire or cable emerging there-from, designed to fit through panel(s) or the wall of a JUNCTION BOX. It may be designed to snap into a knockout hole, or designed with an external thread and furnished with or without a locking nut. For items designed to couple conduit to JUNCTION BOX, see BOX CONNECTOR, ELECTRICAL. See also BUSHING, ELECTRICAL CONDUIT and BUSHING, NONMETALLIC. For items having hexagonal shoulders, see CHASE NIPPLE, CONDUIT.
What is an Insulator Bracket? 144 Items: An Insulator Bracket (BRACKET,INSULATOR) is an item designed to be attached to a supporting surface for the specific purpose of positioning and sustaining an electrical insulator(s). Includes brackets specifically designed for transposing electrical lines.
What is a Cable Reinforcing Link? 21 Items: A Cable Reinforcing Link (LINK,REINFORCING,CABLE) is an item fabricated from metal rod bent longitudinally into an oval shape, one end of which is intended to fit a messenger cable or guy wire and the opposite end formed with a mounting hole for a lag screw. This item is designed to relieve the strain where a messenger cable or wire is installed at an angle to a suspension clamp.
What is a Stuffing Tube Adapter? 72 Items: A Stuffing Tube Adapter (ADAPTER,STUFFING TUBE) is a threaded or unthreaded item designed to mate with the mounting threads or mounting surfaces of a STUFFING TUBE, and to mount the STUFFING TUBE to a continuous structure (bulkhead or deck). The adapter may be recessed on the face to accommodate a gasket and/or washer.
What is a Junction Box? 2471 Items: A Junction Box is an enclosure of other than cast metal designed to house, mount, and protect, but does not include wiring connections or electrical device(s) such as terminals and/or terminal boards, switches, jacks, fuseholders, connectors, circuit breakers and the like. It is designed for and may include a cover and such accessories as mounting hardware, brackets, locks, clamps, mounts and conduit fittings. Excludes CONDUIT OUTLET; and CHAMBER, CABLE TERMINAL. For boxes which include electrical device(s) such as terminals and/or terminal boards, switches, fuseholders, jacks, connectors, circuit breakers and the like, or combinations thereof, see SWITCH BOX; FUZE BOX; JACK BOX; TERMINAL BOX; CIRCUIT BREAKER BOX; and DISTRIBUTION BOX. For boxes wired to provide the interconnecting facilities for a specific major group of electronic items outside of the box, see INTERCONNECTING BOX. See also INTERCONNECTING CABINET.
What is an Electrical Cable Nipple? 547 Items: An Electrical Cable Nipple (CABLE NIPPLE,ELECTRICAL) is a preformed item having high electrical resistance designed for installation on end of cable or lead in order to cover the terminal or termination. It may partially cover the terminal of the item to which the cable or lead is attached. May also provide mechanical protection. Excludes INSULATION SLEEVING, ELECTRICAL.
What is an Electrical Equipment Cabinet? 1478 Items: An Electrical Equipment Cabinet (CABINET,ELECTRICAL EQUIPMENT) is an enclosure generally fabricated of sheet material designed to accommodate (but does not include) electrical/electronic equipment so that the equipment may be operated without removal. It may include wires, cables, terminal boards, connectors, etc., required for equipment operation. For items designed to accommodate equipment mounted on panels, see RACK, ELECTRICAL EQUIPMENT. See also CASE (2) (as modified). Excludes INTERCONNECTING BOX; INTERCONNECTING CABINET; JUNCTION BOX; and TERMINAL BOX.
What is an Electrical Equipment Rack? 2666 Items: An Electrical Equipment Rack (RACK,ELECTRICAL EQUIPMENT) is an open or inclosed frame structure designed to accommodate (but does not include) electrical/electronic equipment mounted on standard width panels so that the equipment may be operated after installation without being removed. It must have panel mounting rails that provide a uniform pattern of mounting holes that will accommodate various combinations of standard width panels. It may include wires, cables, terminal boards, connectors, and the like, required for equipment operation. See also MOUNTING BASE, ELECTRICAL EQUIPMENT; CABINET, ELECTRICAL EQUIPMENT; and CASE (2) (as modified). Excludes MAIN DISTRIBUTING FRAME, TELEPHONE and INTERMEDIATE DISTRIBUTING FRAME, TELEPHONE.
What is an Electrical Entrance Cap? 43 Items: An Electrical Entrance Cap (ENTRANCE CAP,ELECTRICAL) is an item primarily designed to provide for the entrance of electrical wires into a building, structure, or inclosure and to facilitate their connection to feeders or service conductors. It consists of an insulating block and a metallic housing designed to hold the insulating block and to fit an electrical conduit, conduit fitting, or cable of a specified size. This item is primarily intended for use in exposed, wet, or damp locations and is installed so as to preclude the entrance of rain or debris into the conduit. See also CAP, ELECTRICAL.
What is an Electrical Conduit Adapter? 1842 Items: An Electrical Conduit Adapter (ADAPTER,ELECTRICAL CONDUIT) is an item designed to couple or join two different types or sizes of conduits, and/or to be inserted in the opening of a conduit outlet or box to accommodate a conduit of a larger or smaller size; or it may be designed with internal thread on one end for mating with an electrical connector and an external thread on the other end for mating with a conduit coupling nut; or to establish necessary mechanical accommodations between an electrical conduit, conduit assembly and an electrical connector. Excludes REDUCING WASHER, KNOCKOUT and BOX CONNECTOR, ELECTRICAL. See also ADAPTER, CABLE TO CONNECTOR; and CHASE NIPPLE, CONDUIT.
What is an Electrical Conduit Sealing Fitting? 56 Items: An Electrical Conduit Sealing Fitting (SEALING FITTING,ELECTRICAL CONDUIT) is an item of metallic composition with a chamber for sealing compound and two hubs to accommodate electrical conduits of specified sizes. This item is designed with a filler hole and a removable screw plug to enable the pouring of sealing compound into the chamber for the purpose of preventing the passage of explosive gases through a conduit run. The item is primarily designed for use in hazardous locations and may be designed for vertical use, horizontal use, or both. For items which permit the connection or termination of wires, see POTHEAD. See also COUPLING, ELECTRICAL CONDUIT.
What is a Knockout Reducing Washer? 38 Items: A Knockout Reducing Washer (REDUCING WASHER,KNOCKOUT) is an item consisting of a flat, cupped or embossed metallic disk with a centerhole to fit an electrical conduit of a specified size and which is specifically designed to reduce the knockout opening in a box, panel, or wireway for the convenience of terminating electrical conduit of smaller size than the knockout. Excludes ADAPTER, ELECTRICAL CONDUIT.
What is an Electrical Conduit Nipple? 143 Items: An Electrical Conduit Nipple (NIPPLE,ELECTRICAL CONDUIT) is a nipple made of electrical conduit.
What is an Electrical Entrance Elbow? 34 Items: An Electrical Entrance Elbow (ENTRANCE ELBOW,ELECTRICAL) is an item of metallic composition cast in the form of an elbow, which is primarily intended to provide for the angular entrance of wires into a building, structure, or enclosure. This item, specifically designed for installation in exposed locations, has two hubs of a specified size to fit the service entrance conduit and may have a third hub for a driven ground connection. It has a cover which makes it tamper-proof and weather-resistant. It may include facilities for pulling electrical conductors but does not have facilities for mounting wiring devices.
What is an Electrical Conduit Bushing? 290 Items: An Electrical Conduit Bushing (BUSHING,ELECTRICAL CONDUIT) is an item of metal and/or insulating material having internal threads designed to fit over the end of electrical conduit and/or fittings to provide a smooth interior with a rounded edge to prevent damage to the insulation of the wire or cable emerging therefrom. It may be designed to fit over the end of thin wall conduit, and to be fitted with holding (staking) screws, or it may be provided with internal straight threads for attaching to thick wall electrical conduit or fittings. It may be fitted with a temporary knockout cap (bushcap), and grounding or bonding facilities. For externally threaded items, see BOX CONNECTOR, ELECTRICAL; BUSHING, ELECTRICAL CONDUCTOR; CHASE NIPPLE, CONDUIT and BUSHING, STRAIN RELIEF, CABLE. See also FERRULE, ELECTRICAL CONDUIT. Excludes plain sleeve bushings.
What is an Electrical Conduit Bondnut? 17 Items: An Electrical Conduit Bondnut (BONDNUT,ELECTRICAL CONDUIT) is an item of metallic composition, with internal threads, designed to fit the external threads of an electrical conduit or fitting, and which, when installed, provides a method of tightening and locking the connection and completes a positive bond between the conduit and apparatus or fitting to which connected. The bonding or grounding action is accomplished by sharp beveled teeth or by a screw(s). See also LOCKNUT, ELECTRICAL CONDUIT and NUT, COUPLING, ELECTRICAL CONDUIT.
What is an Electrical Conduit Union? 130 Items: An Electrical Conduit Union (UNION,ELECTRICAL CONDUIT) is an item comprising three members, so constructed that one of the members holds the remaining two in a fixed butted position; generally used to connect two conduits, conduit fittings, or a conduit and a conduit fitting in such a manner that they may be disconnected without disturbing the rest of the conduit line. See also COUPLING, ELECTRICAL CONDUIT.
What is an Electrical Conduit Elbow? 419 Items: An Electrical Conduit Elbow (ELBOW,ELECTRICAL CONDUIT) is an item fabricated in the form of an elbow and having both ends threaded female, or with unthreaded connecting facilities on both ends, or connecting facilities on both ends, one of which is a male thread without boss or shoulder. If a locknut or bondnut is included, it shall not be considered as a thread boss or shoulder. It is primarily intended to connect conduit to conduit. It may have a removable cover to facilitate pulling wires, but does not include facilities for mounting wiring devices. For items having a removable cover to facilitate pulling wires and specifically designed for close installation in exposed outdoor locations and which may have facilities for an outside driven ground, see ENTRANCE ELBOW, ELECTRICAL. For items with one end having a male thread with a boss or shoulder, see BOX CONNECTOR, ELECTRICAL. For items having a removable screw cap for pulling wires, with the cap positioned 45 degrees from the connection facilities, see ENTRANCE ELBOW, ELECTRICAL. For items fabricated in the form of an elbow having both ends threaded male, see BEND, ELECTRICAL CONDUIT.
What is a Conduit Outlet? 985 Items: A Conduit Outlet is an item designed to be used in a conduit system for the purpose of providing outlets or attachments for electrical wiring devices and/or designed to provide access and facilitate installment of wires. It may or may not include a cover(s). It does not include wiring devices. Excludes ENTRANCE ELBOW, ELECTRICAL. See also JUNCTION BOX.
What is an Electrical Conduit Bend? 118 Items: An Electrical Conduit Bend (BEND,ELECTRICAL CONDUIT) is an item fabricated in the form of a curved section specifically designed to mechanically join a conduit or conduit fitting to another conduit or conduit fitting. Items of this type do not have a boss or hub at either end, nor do they have facilities for mounting wiring devices or pulling electrical conductors. See also ELBOW, ELECTRICAL CONDUIT and CONDUIT OUTLET.
What is an Electrical Wall Plate? 595 Items: An Electrical Wall Plate (PLATE,WALL,ELECTRICAL) is an item designed to mount directly on a bracket or an electrical current carrying wiring device(s) such as switch(es) or outlet(s) (receptacle). The bracket(s) or electrical current carrying device is mounted in a JUNCTION BOX. For trade designated items designed to be attached directly on or through a bracket or electrical wiring device to a CONDUIT OUTLET, see COVER, CONDUIT OUTLET. For items designed for mounting directly on a JUNCTION BOX, see COVER, JUNCTION BOX.
What is an Interconnecting Box? 482 Items: An Interconnecting Box is an inclosure which includes mounts and protects such items as switches, circuit breakers, jacks, fuseholders, connectors, terminals and/or terminal boards, resistors, capacitors, transformers, and the like. It is primarily designed to interconnect two or more electrical and/or electronic items, except primary power source(s) such as generator(s) and battery(ies). It may include a cover or door. For inclosures which connect one or more primary power source(s) to one or more electrical and/or electronic item(s), see DISTRIBUTION BOX. See also CIRCUIT BREAKER BOX; TERMINAL BOX and INTERCONNECTING CABINET.
What is a Pole Step? 13 Items: A Pole Step (STEP,POLE) is an item designed to be used as a foot rest in ascending and descending utility poles, when attached thereto.
What is an Interior Cable Rack? 78 Items: An Interior Cable Rack (RACK,CABLE,INTERIOR) is an open frame structure primarily designed to support electrical cables in buildings and shelters. Its purpose is to provide, by itself or by joining to similar structures, a path or runway for cable which may connect two or more pieces of electrical equipment. It does not include items designed to hold a single cable. See also RACK, CABLE, UNDERGROUND; and HANGER, CABLE.
What is an Electrical Conduit Ferrule? 274 Items: An Electrical Conduit Ferrule (FERRULE,ELECTRICAL CONDUIT) is an item usually of one piece construction, but which may be comprised of more than one piece, designed to be affixed permanently or temporarily to the end of an electrical conduit to form an end fitting. Unflanged items form a permanent end fitting which affords mechanical protection to emerging conductors. Flanged items are used with another fitting normally a conduit coupling nut, to make the conduit adaptable for connection to an electrical connector, junction box or other conduit accessory or fitting. Excludes RING, ELECTRICAL BONDING; BUSHING, ELECTRICAL CONDUIT; and BUSHING, PLAIN SLEEVE. See also FERRULE-NUT COUPLING, ELECTRICAL CONDUIT.
What is an Underground Cable Rack Hook? 13 Items: An Underground Cable Rack Hook (HOOK,UNDERGROUND CABLE RACK) is a rigid item designed to be perpendicularly attached to an underground cable rack to be used as the supporting arm for cables. May include insulators.
What is an Electrical Conduit End Seal Disk? 28 Items: An Electrical Conduit End Seal Disk (DISK,END SEAL,ELECTRICAL CONDUIT) is a flat circular item fitted on the end of an electrical conduit in order to close the end to prevent the entrance of water or refuse, prior to installation of the wires, during shipment and/or construction. The item may be held in place by means of a conduit bushing and may be easily removed to permit installation of the wires.
What is a Cable Spacer? 104 Items: A Cable Spacer (SPACER,CABLE) is an item constructed specifically to provide a separation between lashed lead covered cable and messenger strand for the prevention of injury to sheath of cable.
What is an Electrical Box Connector? 1449 Items: An Electrical Box Connector (BOX CONNECTOR,ELECTRICAL) is an item designed to mechanically connect in a straight line or an angle electrical conduit, conduit assemblies, wire, wireway, cable, or cable assemblies to a point of termination, such as a junction box, conduit outlet, or the like. The termination end must have an external thread with a boss or shoulder and may be furnished with a locknut or bondnut; or, must have internal thread with which is furnished an externally threaded hub with a wrenching feature; or be of a snap-in type that may be installed from either inside or outside the box and secured with a captive screw. It is not intended to join conduit to conduit. For angle type items having a male thread without a boss or shoulder, see ELBOW, ELECTRICAL CONDUIT. Does not include facilities to mount wiring devices. Excludes CHASE NIPPLE, CONDUIT.
What is an Electrical Conduit Coupling? 391 Items: An Electrical Conduit Coupling (COUPLING,ELECTRICAL CONDUIT) is an item specifically designed and constructed to mechanically connect in a straight line two sections of electrical conduit or like fabrication and of the same size. For three-piece items which may be disassembled without disturbing the rest of the conduit line, see UNION, ELECTRICAL CONDUIT. See also ADAPTER, ELECTRICAL CONDUIT; POTHEAD; and SEALING FITTING, ELECTRICAL CONDUIT.
What is an Electrical Conduit Wye? 167 Items: An Electrical Conduit Wye (WYE,ELECTRICAL CONDUIT) is a type of electrical conduit fitting fabricated in the form of the letter Y, having three hubs permitting conduits and/or conduit fittings to be taken off laterally from the main line of equal degree on each side, or with the main line continuing straight with a branch taking off at an angle. For items of this type having facilities for mounting wiring devices, see CONDUIT OUTLET.
What is a Cable Rack Extension? 17 Items: A Cable Rack Extension (EXTENSION,CABLE RACK) is a metallic irregularly shaped item designed to permit cable racks to be mounted away from the mounting surface to escape obstructions or limited space.
What is an Electrical Bonding Ring? 79 Items: An Electrical Bonding Ring (RING,ELECTRICAL BONDING) is an item of metallic composition, usually round and flat with a center hole or slotted hole designed to accommodate an electrical cable or conduit, and which, when used in conjunction with a cable clamp or similar locking device, completes a positive bond between the cable or conduit fitting, such as connectors, adapters, and couplings, and the cable or conduit shield and/or individual conductor shield(s). See also FERRULE, ELECTRICAL CONDUCTOR.
What is an Electrical Equipment Rack Base? 123 Items: An Electrical Equipment Rack Base (BASE,ELECTRICAL EQUIPMENT RACK) is a structural item which is specifically designed to provide a suitable flat surface to support one or more RACK, ELECTRICAL EQUIPMENT. It may include legs and/or leveling devices. For similar items designed primarily for the purpose of damping shock and/or vibration, see MOUNTING BASE, ELECTRICAL EQUIPMENT. See also STAND, (as modified).
What is an Electrical Cable Splice Protector? 33 Items: An Electrical Cable Splice Protector (PROTECTOR,SPLICE,ELECTRICAL CABLE) is an item specifically designed to be mechanically fastened to an electrical cable on each end of a splice to protect the splice from excessive strain. It usually has provisions for making a waterproof or moisture-proof joint. Excludes INSULATION SLEEVING, ELECTRICAL.
What is an Electrical Conduit Coupling Nut? 193 Items: An Electrical Conduit Coupling Nut (NUT,COUPLING,ELECTRICAL CONDUIT) is an item of metallic composition with internal threads and an internal seat designed to join a ferrule capped conduit to a fitting. See also BONDNUT, ELECTRICAL CONDUIT.
What is an Insulator Bracket Strap? 18 Items: An Insulator Bracket Strap (STRAP,INSULATOR BRACKET) is an item specifically designed to reinforce insulator brackets at their fastenings on a line construction pole when high strength wire or long spans are used.
What is a Junction Box Cover? 552 Items: A Junction Box Cover (COVER,JUNCTION BOX) is a cover containing facilities for mounting directly on a JUNCTION BOX. It may have provisions for the insertion and/or mounting of electrical devices, such as switches, connectors, additional covers, and jewels. It may include the jewel(s). For covers having facilities for mounting on brackets or on current carrying devices such as switches and receptacle connectors, see PLATE, WALL, ELECTRICAL. See also COVER, CONDUIT OUTLET.
What is a Wire Strand Hanger? 27 Items: A Wire Strand Hanger (HANGER,WIRE STRAND) is a metallic item, grooved to fit a wire strand such as a messenger strand, and designed to be attached to a utility pole or other supporting surface for the purpose of horizontally suspending and firmly securing the wire strand. See also HANGER, CABLE, and CLAMP, ELECTRICAL CONDUCTOR, STRAIN. Excludes BRACKET, PIPE.
What is an Electrical Conduit Cross? 10 Items: An Electrical Conduit Cross (CROSS,ELECTRICAL CONDUIT) is a type of electrical conduit fitting fabricated in the form of a cross having four hubs in the same plane, the axes of which form a right angle, and primarily intended to join electrical conduits and/or conduit fittings. For items of this type having ties for mounting wiring devices, see CONDUIT OUTLET.
What is an Electrical Conduit Tee? 84 Items: An Electrical Conduit Tee (TEE,ELECTRICAL CONDUIT) is a type of electrical conduit fitting fabricated in the form of the letter T having three hubs for joining electrical conduits and/or conduit fittings. For items of this type having facilities for mounting wiring devices, see CONDUIT OUTLET.
What is a Blank Panel? 1873 Items: A Blank Panel (PANEL,BLANK) is a panel designed to fill a space not occupied by actual operating components, and may have instructions, component designations, or component identifications etched or printed thereon.
Case,Electrical Equipment Cabinet 73 Items
Case,Switch Box 44 Items
What is a Ground Rod Section? 30 Items: A Ground Rod Section (ROD SECTION,GROUND) is an item which is part of a multi-section ground rod. Excludes items with driving points. see also ROD, GROUND.
What is a Junction Box Extension? 71 Items: A Junction Box Extension (EXTENSION,JUNCTION BOX) is an item designed to be mounted on a JUNCTION BOX to increase the depth of the box.
What is a Stuffing Tube Packing Nut? 87 Items: A Stuffing Tube Packing Nut (PACKING NUT,STUFFING TUBE) is a threaded or unthreaded device, with an unthreaded center hole to accommodate an electrical cable or tube, designed to mate with the threads or sealing components of a stuffing tube body for the purpose of compressing packing around the electrical cable or tube. A component of a STUFFING TUBE.
What is a Transmission Line Grounding Set? 38 Items: A Transmission Line Grounding Set (GROUNDING SET,TRANSMISSION LINE) is an item consisting of two or more clamp type devices with facilities for the connection of jumpers and/or grounding cables. When installed this item provides for the temporary grounding of de-energized electrical transmission line(s) to protect workmen against injury resulting from accidental re-energization of the lines. Excludes CLAMP, ELECTRICAL.
What is a Cable Marker Sleeve? 1191 Items: A Cable Marker Sleeve (SLEEVE,MARKER,CABLE) is a cylindrical item into which a wire or cable is inserted. It is inscribed for identification, to indicate connections or routing of electrical cables and the like. For unmarked items made of insulation material, see INSULATION SLEEVING, ELECTRICAL. For items secured by crimping, slot and tongue, or other similar methods of fastening, see BAND, MARKER.
What is an Electrical Standardized Components Case? 81 Items: An Electrical Standardized Components Case (CASE,STANDARDIZED COMPONENTS,ELECTRICAL) is a case which by virtue of standardization of equipment dimensions is designed to contain one or more components of different basic names. Do not use for cases designed only for specific items or a specific grouping of items.
What is an Electrical Conduit Ferrule-Nut Coupling? 21 Items: An Electrical Conduit Ferrule-Nut Coupling (FERRULE-NUT COUPLING,ELECTRICAL CONDUIT) is an item consisting of a FERRULE, ELECTRICAL CONDUIT upon which is permanently mounted a NUT, COUPLING, ELECTRICAL CONDUIT. It is designed to be attached to an electrical conduit and used to mechanically connect the conduit to another conduit fitting such as a box connector. Excludes BOX CONNECTOR, ELECTRICAL; ADAPTER, ELECTRICAL CONDUIT; and COUPLING, ELECTRICAL CONDUIT.
What is a Strain Electrical Conductor Clamp? 472 Items: A Strain Electrical Conductor Clamp (CLAMP,ELECTRICAL CONDUCTOR,STRAIN) is a clamp designed to support and/or dead end a suspended conductor(s). Must have a provision for attachment to an insulator. Insulator is not included. Excludes HANGER, WIRE STRAND.
What is an Electrical Entrance Cap Shell? 11 Items: An Electrical Entrance Cap Shell (SHELL,ELECTRICAL ENTRANCE CAP) is an item similar to ENTRANCE CAP, ELECTRICAL, but it does not include an insulating block. See also CAP, ELECTRICAL.
What is a Flexible Metal Conduit? 564 Items: A Flexible Metal Conduit (CONDUIT,METAL,FLEXIBLE) is a conduit constructed of circular flexible metal tubing. It may be shielded with a woven metal wire braid covering, with a packing between the joints, and it may have a rubber and/or synthetic rubber or plastic outer protective covering. It contains no fittings. See also CONDUIT, METAL, RIGID. Excludes conduit like items that are designed for other than electrical applications.
What is a Rigid Metal Conduit? 512 Items: A Rigid Metal Conduit (CONDUIT,METAL,RIGID) is a conduit of one-piece tubular construction, designed as thin wall type (EMT) and thick wall type. The items may be threaded and furnished with a COUPLING, ELECTRICAL CONDUIT and/or thread protection. See also CONDUIT ASSEMBLY,METAL, RIGID. Excludes conduit like items that are designed for other than electrical applications.
What is a Rigid Nonmetallic Conduit? 111 Items: A Rigid Nonmetallic Conduit (CONDUIT,NONMETALLIC,RIGID) is a conduit of one piece construction of asbestos and cement, bituminized fiber, or rigid plastics material. The item may have both ends processed for connection by means of a coupling. One coupling may be furnished for each length of conduit. The conduit may or may not be impregnated with coal tar pitch. Excludes conduit like items that are designed for other than electrical applications.
What is a Radio Frequency Cable Splicing Kit? 25 Items: A Radio Frequency Cable Splicing Kit (SPLICING KIT,RADIO FREQUENCY CABLE) is a collection of items used in splicing a radio frequency cable, such as yokes, plugs, cable, switches, and power transformer.
What is a Drive Ring? 10 Items: A Drive Ring is a metal item having an eye attached or integral with a nail-like item. It is designed for running twisted pair, bridle, or parallel drop wires on building walls, fences, poles and the like. For similar items having threaded ends, see BRIDLE RING. Excludes HOOK, SUPPORT.
What is a Bridle Ring? 12 Items: A Bridle Ring is a metal item having an open eye on one end and a wood screw, or machine thread on the opposite end. The machine thread item may be furnished with a nut or toggle attachment. It is designed for running twisted pair, bridle or parallel drop wires on building walls, fences, poles, and the like. For similar items having a drive nail end, see DRIVE RING. Excludes HOOK, SUPPORT.
What is an Electrical Equipment Leg? 151 Items: An Electrical Equipment Leg (LEG,ELECTRICAL EQUIPMENT) is an item which, in conjunction with one or more similar items, aids in the support of electrical equipment. See also LEG SECTION, ELECTRICAL EQUIPMENT.
What is an Electrical Equipment Leg Section? 60 Items: An Electrical Equipment Leg Section (LEG SECTION,ELECTRICAL EQUIPMENT) is an item which in itself is not a complete functioning item. It consists of parts which, together with other similar parts, form an electrical equipment leg.
What is a Conduit Chase Nipple? 86 Items: A Conduit Chase Nipple (CHASE NIPPLE,CONDUIT) is an externally threaded item having a hexagonal shoulder with a smooth bore. It may be used to connect two junction boxes or to accommodate thin wall conduit or tubing by slip fit to a junction box or conduit outlet. It may or may not be furnished with a locknut. For items externally and internally threaded, see ADAPTER, ELECTRICAL CONDUIT. See also BUSHING, ELECTRICAL CONDUCTOR.
What is a Cable Strain Relief Bushing? 299 Items: A Cable Strain Relief Bushing (BUSHING,STRAIN RELIEF,CABLE) is an insulating item designed to prevent movement along the axis of an electric wire or cable in either direction when placed in the chassis of such items as electric fans, irons, drills, motors, radios, clocks and the like. It may be designed for use in the central column of a gun mount and the like. See also COLLAR, CABLE.
What is an Electrical Nonmetallic Conduit Assembly? 1312 Items: An Electrical Nonmetallic Conduit Assembly (CONDUIT ASSEMBLY,NONMETALLIC,ELECTRICAL) is a specific length of tubing or conduit, nonmetallic, rigid or flexible, with or without electrical rating, and with permanently attached ferrule(s), coupling nut(s), or the like. It may include one or more woven wire braid cover(s). Excludes detachable fittings such as tee(s), wye(s) or elbow(s). Also excludes conduit like items that are designed for other than electrical applications.
What is a Conduit Outlet Cover? 383 Items: A Conduit Outlet Cover (COVER,CONDUIT OUTLET) is an item of any material, with or without threads, designed to mate with a CONDUIT OUTLET or a SEALING FITTING, ELECTRICAL CONDUIT. It may be designed as a removable side plate cover with or without hubs. It may have provisions for draining or venting. It may be designed for the insertion and/or mounting of electrical devices, such as switches, receptacle connectors, and indicator light lenses. It may include mechanisms for the external operation of switches but does not include the wiring devices. For items designed to mount directly on a bracket or an electrical current carrying wiring device, see PLATE, WALL, ELECTRICAL. See also COVER, JUNCTION BOX.
What is an Electrical Conduit Coupling Nut Clamp? 44 Items: An Electrical Conduit Coupling Nut Clamp (CLAMP,COUPLING NUT,ELECTRICAL CONDUIT) is an item designed to be clamped on a conduit. It has extending prongs to engage and lock in position a NUT, COUPLING, ELECTRICAL CONDUIT.
What is an Electrical Equipment Shelf? 676 Items: An Electrical Equipment Shelf (SHELF,ELECTRICAL EQUIPMENT) is an item relatively thin in its vertical dimension, designed to provide a horizontal working surface on the front of a CABINET, ELECTRICAL EQUIPMENT or a RACK, ELECTRICAL EQUIPMENT. May include wiring, power outlets and similar accessories. May be furnished with slides to permit stowing within the cabinet or rack when not in actual use.
What is a Shop Set Installation Electrical Kit? 23 Items: A Shop Set Installation Electrical Kit (ELECTRICAL KIT,SHOP SET INSTALLATION) is a collection of wiring and fixture items, such as box, cable, connector, cord, cover, cutout, fuse, receptacle, socket, switch, and the like, designed to wire shop set equipment when installing it in a shop truck as part of the basic load.
What is a Line Supporting Strap? 16 Items: A Line Supporting Strap (STRAP,LINE SUPPORTING) is a flexible strap, furnished with a buckle, specificifically designed to support other items, such as cable(s), wire(s), tube(s), and the like. The buckle may be permanently assembled and may be provided with a mounting feature. The strap may be used to bridge a channel by mounting the buckle and strap separately. Excludes CLAMP, LOOP; STRAP, RETAINING; STRAP, LEATHER; and STRAP, WEBBING.
What is an Electrical Conduit Locknut? 202 Items: An Electrical Conduit Locknut (LOCKNUT,ELECTRICAL CONDUIT) is an item having internal threads designed to fit the external threads of an electrical conduit or fitting for connecting to a junction box, panel, wireway, or other point of termination, and which, when installed, provides a method of tightening to lock the connection. The items may be either flat-sided or circular in external shape and must have a specific conduit size designation. SEE BONDNUT, ELECTRICAL CONDUIT and LOCKNUT, TUBE FITTING. Excludes NU T (1), PLAIN HEXAGON.
What is a Flexible Nonmetallic Conduit? 657 Items: A Flexible Nonmetallic Conduit (CONDUIT,NONMETALLIC,FLEXIBLE) is a conduit of one piece flexible, nonmetallic, tubular construction. The item may have an outer covering for additional mechanical protection, a woven wire braid for interference suppression, and/or wire reinforcement. For items having rated electrical characteristics, see INSULATION SLEEVING, ELECTRICAL. Excludes TUBING, NONMETALLIC; and TUBING, PLASTIC, SPIRAL WRAP. Excludes conduit like items that are designed for other than electrical applications.
What is an Electrical Equipment Drawer? 518 Items: An Electrical Equipment Drawer (DRAWER,ELECTRICAL EQUIPMENT) is an item designed to slide in and out of a CABINET, ELECTRICAL EQUIPMENT or RACK, ELECTRICAL EQUIPMENT and used to mount and/or store electrical/electronic equipment. It does not include the electrical/electronic equipment, but may include wires, cables, terminal boards, connectors, etc.
What is an Electrical Equipment Mounting Base? 3161 Items: An Electrical Equipment Mounting Base (MOUNTING BASE,ELECTRICAL EQUIPMENT) is a tray or racklike item designed to provide a supporting surface to which electrical/electronic equipment may be secured when installed in aircraft, vehicles, or other types of mobile equipment. It may be equipped with shock or vibration isolation devices and/or wires, cables, terminal boards, connectors, etc. Excludes BASE, ELECTRICAL EQUIPMENT RACK and MOUNT, RESILIENT. See also RACK, ELECTRICAL EQUIPMENT.
What is an Electronic Junction Rack? 253 Items: An Electronic Junction Rack (RACK,ELECTRONIC JUNCTION) is an open frame structure specifically designed to accommodate (but does not include) electronic terminal junctions (TERMINAL BOARD; TERMINAL (1), FEEDTHRU; and the like). The item may consist of separable or nonseparable channels, mounting blocks and fastening devices. Mounting blocks are designed so the assembly can be mounted on panels or bulkheads. Tightening the fastening devices which secure the channels to the mounting blocks will also secure terminal junctions within the frame assembly. Excludes RACK, ELECTRICAL EQUIPMENT; TERMINAL BOARD; JUNCTION BOX; and HARDWARE KIT, ELECTRONIC EQUIPMENT.
What is a Safety Shorting Probe? 16 Items: A Safety Shorting Probe (PROBE,SAFETY SHORTING) is a device used to discharge the voltage stored in cathode ray tubes and other electronic equipment which have capacitor type filtering circuits that retain a voltage charge after the primary power has been removed. See also DISCHARGER, ELECTROSTATIC.
What is an Electrical Tie Down Mounting Base? 626 Items: An Electrical Tie Down Mounting Base (MOUNTING BASE,TIE DOWN,ELECTRICAL) is an item used in conjunction with STRAP, TIEDOWN, ELECTRICAL COMPONENTS to secure wire(s) or cable(s) to a supporting surface.
What is a Raceway Cover? 196 Items: A Raceway Cover (COVER,RACEWAY) is an item used in conjunction with open style raceway for the protection of electrical wires and/or cables. May be attached by snap closure, stud and nut, or similar device. Generally furnished in bulk quantities.
Raceway,Metallic 376 Items
Raceway,Nonmetallic 122 Items
What is an Electrical-Electronic Equipment Panel? 2447 Items: An Electrical-Electronic Equipment Panel (PANEL,ELECTRICAL-ELECTRONIC EQUIPMENT) is a panel which is designed to accommodate, but does not include connectors, displays, indicators, jacks, meters, switches, and the like. It may include clinch nuts or fastening devices as part of the item. Excludes PANEL, BLANK.
What is an Electric Cable Joint Box Supplementary Equipment? 14 Items: An Electric Cable Joint Box Supplementary Equipment (SUPPLEMENTARY EQUIPMENT,JOINT BOX,ELECTRIC CABLE) is a pre-determined combination of different accessories which are packed as a set and are used as supplement to the normal assembly accessories of the JOINT BOX, ELECTRIC CABLE.
What is an Electrical-Electronic Equipment Chassis? 5595 Items: An Electrical-Electronic Equipment Chassis (CHASSIS,ELECTRICAL-ELECTRONIC EQUIPMENT) is a box, frame, or plate fabricated of electrically conductive material designed to mount, but which does not include, electronic components and their associated circuitry. It may have facilities for attachment to a rack or cabinet or to accommodate specially designed components. It may include a shielding function, integral wiring, and mounting hardware as part of the item. Excludes MOUNTING BASE, ELECTRICAL EQUIPMENT.
What is a Mounting Plate? 324 Items: A Mounting Plate (PLATE,MOUNTING) is a metallic or nonmetallic item which is rigid, flat and generally smooth. Its thickness is small in comparison to its length and width. It is designed for mounting another item and may have drilled or threaded holes or other facilities for mounting to a supporting object or surface. See SUPPORT, as modified. Do not use if a more specific name applies.
What is an Electrical Conduit Ferrule Anchor Plate? 13 Items: An Electrical Conduit Ferrule Anchor Plate (ANCHOR PLATE,ELECTRICAL CONDUIT FERRULE) is a piece of flat material, specially designed to secure a FERRULE, ELECTRICAL CONDUIT.
What is a Nonmetallic Raceway Assembly? 39 Items: A Nonmetallic Raceway Assembly (RACEWAY ASSEMBLY,NONMETALLIC) is a channel consisting of one or more parts with other than circular cross sections. The item forms part of bulk quantities which have been specially treated and provided with miter heads and/or mounting holes, for example. It may also be produced in one piece by special molding processes such as thermoplastic pressure die-casting. The item protects electrical wires and/or cables against mechanical damage. Excludes RACEWAY (1), NONMETALLIC.
What is a Metallic Raceway Assembly? 149 Items: A Metallic Raceway Assembly (RACEWAY ASSEMBLY,METALLIC) is a channel consisting of one or more parts with other than circular cross sections. The item is not supplied in bulk quantities and has a particular shape with specific dimensions conforming to a predetermined cable run (e.g., angular or U-shape). The item protects cables against damage. Excludes RACEWAY (1), METALLIC.
What is an Electrical Box Sealing Flange? 10 Items: An Electrical Box Sealing Flange (FLANGE,SEALING,ELECTRICAL BOX) is an item designed for tightly sealing those openings of a JUNCTION BOX towards the outside or inside that are neither provided for being connected with other JUNCTION BOX nor for cable entry. Excludes FLANGE, ADAPTER, ELECTRICAL BOX and FLANGE, ELECTRICAL BOX ENTRY.
What is an Electrical Box Entry Flange? 15 Items: An Electrical Box Entry Flange (FLANGE,ELECTRICAL BOX ENTRY) is an item designed for tightly sealing the openings of a JUNCTION BOX, provided for cable entry, towards the inside or outside. It may include openings or knock-out holes with or without threads that are provided for the installation of STUFFING TUBE or other cable entries. Excludes FLANGE, SEALING, ELECTRICAL BOX and FLANGE, ADAPTER, ELECTRICAL BOX.
What is an Electrical Equipment Foot? 90 Items: An Electrical Equipment Foot (FOOT,ELECTRICAL EQUIPMENT) is an item which in conjunction with an electrical equipment leg or the like, aids in the support of electrical equipment. It is a broad based metallic or nonmetallic item which serves as a stabilizer.
What is an Electrical Standardized Components Case Section? 21 Items: An Electrical Standardized Components Case Section (CASE SECTION,STANDARDIZED COMPONENTS,ELECTRICAL) is an item of various shapes or design representing an integral part of a CASE (2), STANDARDIZED COMPONENTS, ELECTRICAL. It may include fastening, sealing, padding and/or locking devices. It does not include components.
What is a Guide Rail? 228 Items: A Guide Rail (RAIL,GUIDE) is an item used for fixing/mounting TERMINAL JUNCTION BLOCK, SECTIONAL.
What is an Electronic Equipment Mounting Tray? 946 Items: An Electronic Equipment Mounting Tray (TRAY,MOUNTING,ELECTRONIC EQUIPMENT) is an item which facilitates the mounting of electronic/electrical equipment(s) into racks and the like, having holes and/or clamping devices enabling quick replacement of the mounted equipment. does not include the equipment for which designed. may include interconnecting facilities and resilient mountings. excludes DRAWER, ELECTRICAL EQUIPMENT, RACK MOUNTED; DRAWER, ELECTRICAL EQUIPMENT CABINET; CHASSIS, ELECTRICAL EQUIPMENT and PLATE, MOUNTING, ELECTRICAL EQUIPMENT.
What is an Electrical Conductor Protector? 25 Items: An Electrical Conductor Protector (PROTECTOR,ELECTRICAL CONDUCTOR) is an item designed to be interposed between an electrical conductor which may be bare or insulated and its support or housing to prevent chafing caused by contraction and expansion due to changes in the ambient temperature or damage or injury from outside sources. Excludes such items as loom, cotton sleeving, rubber blankets, grade clamps, and all types of conduit and INSULATION SLEEVING, ELECTRICAL.
What is an Electrical Fitting Mounting Base? 92 Items: An Electrical Fitting Mounting Base (BASE,MOUNTING,ELECTRICAL FITTING) is an item serving as a base for electrical pieces such as switches, ceiling roses. It is usually recessed at the base for accommodating wires.
What is a Rigid Metal Conduit Assembly? 597 Items: A Rigid Metal Conduit Assembly (CONDUIT ASSEMBLY,METAL,RIGID) is a straight or prebent length of a CONDUIT, METAL, RIGID complete with permanently attached fitting(s), such as flanges, wye(s) and tee(s). See also TUBE ASSEMBLY, METAL and CASING (as modified). Excludes conduit like items that are designed for other than electrical applications.
What is an Interconnecting Cabinet? 41 Items: An Interconnecting Cabinet is an enclosure, the principal purpose of which is to house, protect, and provide a connecting or branching point for one or more electrical circuits. It is wired to provide the interconnecting facilities for a specific group of electrical and/or electronic items outside of the interconnecting cabinet. It may contain parts such as capacitors, resistors, fuses, relays and terminal boards. In addition, it includes panel(s) on which are mounted control and instrumenation devices associated with the internal components of the cabinet. For items not including such panels. See CABINET, ELECTRICAL EQUIPMENT. See also CIRCUIT BREAKER BOX; DISTRIBUTION BOX; INTERCONNECTING BOX; JUNCTION BOX and TERMINAL BOX.
What is an Electrical Cable Assembly Protector? 74 Items: An Electrical Cable Assembly Protector (PROTECTOR,ELECTRICAL CABLE ASSEMBLY) is an item specifically designed to protect an electrical cable assembly from damage by other items during assembly and/or disassembly operations of associated equipment. Excludes such items as loom, cotton sleeving, rubber blankets, all types of conduit, INSULATION SLEEVING, ELECTRICAL and PROTECTOR, ELECTRICAL CABLE.
What is an Electrical Components Tie Down Strap? 2073 Items: An Electrical Components Tie Down Strap (STRAP,TIE DOWN,ELECTRICAL COMPONENTS) is a preformed item of flexible or semiflexible material of various cross-sectional shapes. It may be tapered to a point at one or both ends, or provided with holes, slots, detents, or other locking devices. It is designed to surround wiring harnesses and other electrical/electronic components. It may be preprinted with legendary characters, symbol(s), letter(s), numeral(s), or color coded, and may be provided with means for securing to other objects. Excludes BAND, MARKER; CLAMP, ELECTRICAL; CLAMP, LOOP; MARKER, IDENTIFICATION; and STRAP, RETAINING.
What is an Electric Component Rail Guide Stop? 15 Items: An Electric Component Rail Guide Stop (STOP,RAIL GUIDE,ELECTRIC COMPONENT) is a metallic or nonmetallic item or various shapes designed to be attached at the end of a RAIL,GUIDE to prevent movement of electric component. It may include facilities for a pin, set screw, or the like to allow for adjustment.
What is a Raceway End Cap? 12 Items: A Raceway End Cap (END CAP,RACEWAY) is an item which is used to close right and or left side of RACEWAY (WITH MODIFIER).
What is an Electrical Cable Ground Guard? 23 Items: An Electrical Cable Ground Guard (GUARD,GROUND,ELECTRICAL CABLE) is a metallic or nonmetallic item of various shape designed to be placed on floor to protect onr or several electrical cable or cord from damages caused by the personnel vehicular, equipment and the like. Excludes: PROTECTOR,ELECTRICAL CABLE and PROTECTOR,ELECTRICAL CABLE ASSEMBLY.

Stock Items From Supply Class 5975 Page 169 of 176

5975-01-187-0810
Mixer Mtg Bracket

011870810
857042-2: RNCC: 3 | RNVC: 2

17 Aug 1984

5975-01-626-2890
Electrical-Electronic Equipment Panel

016262890
734-65223-1: RNCC: 3 | RNVC: 2
734-65223: RNCC: D | RNVC: 9

5 Mar 2014

5975-01-626-4617
Electrical-Electronic Equipment Panel

016264617
734-65229-1: RNCC: 3 | RNVC: 2
734-65229: RNCC: D | RNVC: 9

11 Mar 2014

5975-01-627-0853
Electrical-Electronic Equipment Chassis

016270853
681844-B21: RNCC: 3 | RNVC: 2
17.000.0691.00: RNCC: 5 | RNVC: 2

1 Apr 2014

5975-01-664-1938
Electrical Equipment Leg Section

016641938
SP-8: RNCC: 3 | RNVC: 2

9 Jun 2017

5975-01-666-6623
Interconnecting Box

016666623
352E2342-2: RNCC: 3 | RNVC: 2

15 Sep 2017

5975-01-665-5790
Electrical Equipment Shelf

016655790
40200-4850-50: RNCC: 3 | RNVC: 2

4 Aug 2017

5975-01-666-5183
Electrical Equipment Shelf

016665183
70600-82159-043: RNCC: 3 | RNVC: 2

11 Sep 2017

5975-01-668-3549
Electrical Components Tie Down Strap

016683549
CB9459P3: RNCC: 3 | RNVC: 2

20 Nov 2017

5975-01-664-3644
Electrical Equipment Rack

016643644
295A300-1: RNCC: 3 | RNVC: 2

16 Jun 2017

5975-01-666-6462
Electrical-Electronic Equipment Panel

016666462
352SK190-101: RNCC: 3 | RNVC: 2

14 Sep 2017

5975-01-420-8487
Electrical Box Connector

014208487
051781A1: RNCC: 3 | RNVC: 2

26 Oct 1995

5975-01-627-9526
Mounting Elect Tray

016279526
RR1054-1: RNCC: 3 | RNVC: 2

3 May 2014

5975-01-628-2887
Electrical-Electronic Equipment Chassis

016282887
850-13100: RNCC: 3 | RNVC: 2

17 May 2014

5975-01-629-0864
Insulator Bracket

016290864
287A4131-25: RNCC: 3 | RNVC: 2

18 Jun 2014

5975-01-469-2038
Electrical Fitting Mounting Base

014692038
12433-E: RNCC: 3 | RNVC: 2

5 Nov 1999

5975-01-471-0518
Electrical Box Connector

014710518
061855: RNCC: 3 | RNVC: 2
968C061855: RNCC: 5 | RNVC: 9

20 Jan 2000

5975-01-500-0318
Electrical Equipment Mounting Base

015000318
KC84265-003: RNCC: 3 | RNVC: 2

12 Aug 2002

5975-01-469-6020
Electrical Equipment Mounting Base

014696020
622-9411-001: RNCC: 3 | RNVC: 2

16 Nov 1999

5975-01-269-9693
Electrical Wall Plate

012699693
771-54: RNCC: 3 | RNVC: 2

24 Dec 1987

5975-01-624-1970
Electrical-Electronic Equipment Panel

016241970
68A810413-1015: RNCC: 3 | RNVC: 2

18 Dec 2013

5975-01-625-4882
Metallic Raceway

016254882
80038800028: RNCC: 3 | RNVC: 9

5 Feb 2014

5975-01-624-8028
Cable Collar

016248028
232A1402-10: RNCC: 3 | RNVC: 2

15 Jan 2014

5975-01-642-0745
Wire Rope Isolator

016420745
WR16-850-08EM: RNCC: 3 | RNVC: 2

11 Feb 2015

5975-01-645-2755
Electrical-Electronic Equipment Chassis

016452755
5069-8598: RNCC: 3 | RNVC: 9

10 Jun 2015

5975-01-424-2011
Electrical-Electronic Equipment Chassis

014242011
3C6000: RNCC: 3 | RNVC: 9

23 Jan 1996

5975-01-627-8512
Electrical Components Tie Down Strap

016278512
DTHEH-Q0: RNCC: 3 | RNVC: 2

30 Apr 2014

5975-01-627-7510
Cable Marker Sleeve

016277510
TMS-90-SCE-3/8: RNCC: 3 | RNVC: 2

25 Apr 2014

5975-01-627-7063
Prom Flash

016277063
216C9881VER2.1.1.06: RNCC: 3 | RNVC: 1

24 Apr 2014

5975-01-627-8997
Cable Retaining Fen

016278997
HLP10B: RNCC: 3 | RNVC: 2

1 May 2014

5975-01-495-8419
Electrical-Electronic Equipment Chassis

014958419
546-6563-000: RNCC: 3 | RNVC: 2

26 Mar 2002

5975-01-499-6855
Electronic Junction Rack

014996855
1505963B-R: RNCC: 3 | RNVC: 2

31 Jul 2002

5975-01-234-6641
Wiring Duct

012346641
LD3WH6-A: RNCC: 3 | RNVC: 2

18 Jun 1986

5975-01-235-0632
Blank Panel

012350632
57977-40235-2: RNCC: 3 | RNVC: 2

24 Jun 1986

5975-01-621-2228
Electrical-Electronic Equipment Chassis

016212228
68D411203-1001: RNCC: 3 | RNVC: 2

28 Aug 2013

5975-01-621-8425
Electrical Equipment Mounting Base

016218425
822-2474-001: RNCC: 3 | RNVC: 2

18 Sep 2013

5975-01-623-0730
Electrical-Electronic Equipment Chassis

016230730
IPC-510MB-00XBE: RNCC: 3 | RNVC: 2

30 Oct 2013

5975-01-623-3333
Electrical Equipment Rack

016233333
16E1713-19: RNCC: 3 | RNVC: 2
85VE000102-105: RNCC: 8 | RNVC: 2

8 Nov 2013

5975-01-623-6688
Switch Box Case

016236688
GS748TS: RNCC: 3 | RNVC: 2
VCH V00777 01 107148A 01: RNCC: 5 | RNVC: 2

25 Nov 2013

5975-01-641-3364
Electrical Components Tie Down Strap

016413364
SAE-AS23190: RNCC: 3 | RNVC: 1
SAE-AS33671-1-1: RNCC: 3 | RNVC: 2
SAE-AS33671-1-1: RNCC: 3 | RNVC: 9
AS33671: RNCC: 5 | RNVC: 1
MS3367-1-1: RNCC: 5 | RNVC: 2
MS3367-1-1: RNCC: 5 | RNVC: 9
AS33671: RNCC: 5 | RNVC: 9

16 Jan 2015

5975-01-470-1161
Flexible Metal Conduit Assembly

014701161
230733-DL0000: RNCC: 3 | RNVC: 2
17B2E2000-559: RNCC: 7 | RNVC: 2

7 Dec 1999

5975-01-476-4775
Electrical Nonmetallic Conduit Assembly

014764775
70107882-19: RNCC: 3 | RNVC: 2
38597ASSY70107882-19: RNCC: 5 | RNVC: 2

13 Jul 2000

5975-01-492-9830
Electrical-Electronic Equipment Chassis

014929830
1582AS187-1: RNCC: 3 | RNVC: 2

18 Dec 2001

5975-01-467-9045
Cable Marker Sleeve

014679045
13074005-1: RNCC: 3 | RNVC: 2

20 Sep 1999

5975-01-468-7316
Electrical Equipment Mounting Base

014687316
775-4538-003: RNCC: 3 | RNVC: 2

20 Oct 1999

5975-01-472-5723
Cable Marker Sleeve

014725723
605B798H12: RNCC: 3 | RNVC: 2
605B798H12: RNCC: 3 | RNVC: 9

8 Mar 2000

5975-01-424-0314
Electrical Equipment Cabinet

014240314
4B2A00: RNCC: 3 | RNVC: 2

18 Jan 1996

5975-01-624-3672
Electrical Components Tie Down Strap

016243672
A11089: RNCC: 3 | RNVC: 2

27 Dec 2013

5975-01-624-9772
Electrical-Electronic Equipment Chassis

016249772
782302-01: RNCC: 3 | RNVC: 2

21 Jan 2014

5975-01-624-9726
Electrical Components Tie Down Strap

016249726
BT4S-M39: RNCC: 3 | RNVC: 2

21 Jan 2014

5975-01-624-4721
Electrical Box Divider

016244721
SBB-2-13: RNCC: 3 | RNVC: 2

3 Jan 2014

5975-01-625-1775
Stuffing Tube

016251775
8615010A: RNCC: 3 | RNVC: 2

28 Jan 2014

5975-01-625-6082
Electrical Conductor Bushing

016256082
007731: RNCC: 3 | RNVC: 2

10 Feb 2014

5975-01-624-9572
Electrical Equipment Mounting Base

016249572
ASR-9010-4P-KIT: RNCC: 3 | RNVC: 2
ASR-9010-4P-KIT: RNCC: 5 | RNVC: 2

21 Jan 2014

5975-01-625-6416
Electrical-Electronic Equipment Panel

016256416
807993-13: RNCC: 3 | RNVC: 2
870667-204: RNCC: 5 | RNVC: 2
870667-203: RNCC: 5 | RNVC: 9

11 Feb 2014

5975-01-625-4879
Metallic Raceway

016254879
80038800115: RNCC: 3 | RNVC: 9

5 Feb 2014

5975-01-625-7687
Electrical Equipment Cabinet

016257687
ED-48000B: RNCC: 3 | RNVC: 2

13 Feb 2014

5975-01-626-3703
Electrical-Electronic Equipment Panel

016263703
734-65115-1: RNCC: 3 | RNVC: 2
734-65115: RNCC: D | RNVC: 9

7 Mar 2014

5975-01-626-4170
Electrical Equipment Mounting Base

016264170
734-10023-15: RNCC: 3 | RNVC: 2
734-10023: RNCC: D | RNVC: 9

10 Mar 2014

5975-01-625-1950
Cable Strain Relief Bushing

016251950
0-182661-1: RNCC: 3 | RNVC: 2

28 Jan 2014

5975-01-625-2218
Electrical-Electronic Equipment Panel

016252218
K00022595: RNCC: 3 | RNVC: 2

28 Jan 2014

5975-01-484-9821
Electrical Cable Support

014849821
16D4005-671: RNCC: 3 | RNVC: 2

11 May 2001

5975-01-487-1722
Blank Panel

014871722
068534: RNCC: 3 | RNVC: 2

26 Jul 2001

5975-01-487-8630
Cable Marker Sleeve

014878630
G21332: RNCC: 3 | RNVC: 2
G95948: RNCC: D | RNVC: 9

21 Aug 2001

5975-01-264-5426
Electrical Equipment Cabinet

012645426
0N393052: RNCC: 3 | RNVC: 2
CY-8545/GSQ-234: RNCC: 5 | RNVC: 2

2 Oct 1987

5975-01-264-3927
Shielding Sleeve

012643927
14-1114-1601AB: RNCC: 3 | RNVC: 2

30 Sep 1987

5975-01-264-5423
Electrical Equipment Cabinet

012645423
0N393054: RNCC: 3 | RNVC: 2
CY-8543/GSQ-233: RNCC: 5 | RNVC: 2

2 Oct 1987

5975-01-618-6308
Electronic Equipment Mounting Tray

016186308
114E9546G1: RNCC: 3 | RNVC: 2

30 Apr 2013

5975-01-618-4060
Stuffing Tube Adapter

016184060
7188373: RNCC: 3 | RNVC: 2

23 Apr 2013

5975-01-618-6314
Electrical-Electronic Equipment Panel

016186314
65707-70028-042: RNCC: 3 | RNVC: 2

30 Apr 2013

5975-01-619-9500
Joining Kit

016199500
150-111-3: RNCC: 3 | RNVC: 2

24 Jun 2013

5975-01-620-1893
Guide. Rail

016201893
MDGT10: RNCC: 3 | RNVC: 2
5D0517-5: RNCC: 5 | RNVC: 2

8 Jul 2013

5975-01-620-1516
Electrical Equipment Drawer

016201516
8157829-000: RNCC: 3 | RNVC: 2

3 Jul 2013

5975-00-030-2981
Guy Plate

000302981
SCC66290: RNCC: 3 | RNVC: 2

1 Jan 1963

5975-01-632-1173
Electrical-Electronic Equipment Panel

016321173
DE-C-3420-1: RNCC: 3 | RNVC: 2

8 Oct 2014

5975-01-633-5192
Flexible Nonmetallic Conduit

016335192
7-511130080-015: RNCC: 3 | RNVC: 2

25 Nov 2014

5975-00-989-2005
Electrical Equipment Cabinet

009892005
DL128: RNCC: 3 | RNVC: 1
CR1741HG: RNCC: 5 | RNVC: 1

1 Jan 1962

5975-01-491-9483
Interconnecting Box

014919483
VP042104-101: RNCC: 3 | RNVC: 2
VP042104-201: RNCC: 5 | RNVC: 2
VP042104-201: RNCC: 5 | RNVC: 9

7 Nov 2001

5975-01-523-0125
Electrical Box Connector

015230125
9D1056-103: RNCC: 3 | RNVC: 2
9D01026-103: RNCC: 5 | RNVC: 9

17 Aug 2004

5975-01-525-8271
Insulator Bracket

015258271
63C41234: RNCC: 3 | RNVC: 2

24 Nov 2004

5975-01-616-3987
Electrical Components Tie Down Strap

016163987
KH5056: RNCC: 3 | RNVC: 9
KH5056: RNCC: C | RNVC: 1

12 Feb 2013

5975-01-614-0859
Flexible Metal Conduit

016140859
M24758/1-12: RNCC: 3 | RNVC: 2

27 Nov 2012

5975-00-127-4310
Interconnecting Box Cover

001274310
0N132104: RNCC: 3 | RNVC: 2

2 Dec 1968

5975-00-127-4309
Interconnecting Box Cover

001274309
0N080095: RNCC: 3 | RNVC: 2

2 Dec 1968

5975-01-627-9002
Raceway Cover

016279002
HBLTT5ECB: RNCC: 3 | RNVC: 2

1 May 2014

5975-01-631-1249
Electrical-Electronic Equipment Panel

016311249
DE-C-3911: RNCC: 3 | RNVC: 2
185189: RNCC: 5 | RNVC: 2

2 Sep 2014

5975-00-985-6312
Electrical Cable Tray

009856312
6A12050: RNCC: 3 | RNVC: 2

14 May 1972

5975-00-985-6313
Electrical Cable Tray

009856313
6A06070: RNCC: 3 | RNVC: 2

14 May 1972

5975-01-620-7945
Electrical Components Tie Down Strap

016207945
BC4LH-S25-LO: RNCC: 3 | RNVC: 2
00099897N: RNCC: 5 | RNVC: 2
00099897N: RNCC: 5 | RNVC: 2
B0084-3172: RNCC: 5 | RNVC: 2
00098870N: RNCC: 5 | RNVC: 9
00098870N: RNCC: 5 | RNVC: 9

12 Aug 2013

5975-01-621-8426
Electrical Equipment Mounting Base

016218426
822-2473-001: RNCC: 3 | RNVC: 2

18 Sep 2013

5975-01-521-0276
Electrical Equipment Mounting Base

015210276
A0LAX021: RNCC: 3 | RNVC: 2

7 Jun 2004

5975-01-523-1237
Electrical-Electronic Equipment Panel

015231237
47761-1007-101: RNCC: 3 | RNVC: 2

20 Aug 2004

5975-01-199-2050
Cable Hanger

011992050
13075922: RNCC: 3 | RNVC: 9
13075922: RNCC: 5 | RNVC: 2

18 Jan 1985

5975-01-614-8869
Electrical Equipment Rack

016148869
701M6510: RNCC: 3 | RNVC: 2

18 Dec 2012

5975-01-625-4900
Rigid Metal Conduit

016254900
62001330050: RNCC: 3 | RNVC: 9

5 Feb 2014

5975-01-625-6476
Electrical Equipment Mounting Base

016256476
725216-801: RNCC: 3 | RNVC: 2

11 Feb 2014

5975-01-627-4070
Cable Rack Extension

016274070
UFS 150/200: RNCC: 3 | RNVC: 2

14 Apr 2014

5975-00-983-4507
Conduit

009834507
7445343-300: RNCC: 3 | RNVC: 2

1 Jan 1962

5975-01-489-0580
Electrical Components Tie Down Strap

014890580
PLT3H-TL30: RNCC: 3 | RNVC: 2

10 Sep 2001

5975-01-489-1470
Electrical Equipment Rack

014891470
5HU50400-111: RNCC: 3 | RNVC: 2

13 Sep 2001

5975-01-620-1174
Chassis Base

016201174
715564-1: RNCC: 3 | RNVC: 2

2 Jul 2013

5975-01-516-1523
Panel Patch Kit

015161523
155-0908: RNCC: 3 | RNVC: 2

22 Dec 2003

5975-01-647-3404
Junction Box

016473404
JA15007AE-G01: RNCC: 3 | RNVC: 2

18 Aug 2015

5975-01-647-4937
Blank Panel

016474937
295A322-1: RNCC: 3 | RNVC: 2

24 Aug 2015

5975-01-648-1156
Electrical-Electronic Equipment Chassis

016481156
E7X66A: RNCC: 3 | RNVC: 2
E7X66A: RNCC: 5 | RNVC: 2
M6720 LLF: RNCC: 5 | RNVC: 2

15 Sep 2015

5975-01-648-8632
Mounting Plate

016488632
25-8NF4589-1A: RNCC: 3 | RNVC: 2
25-8NF4589-1A: RNCC: 3 | RNVC: 9

9 Oct 2015

5975-00-068-4472
Electrical Equipment Cabinet

000684472
CY2522CWLR1: RNCC: 3 | RNVC: 2
K663250001: RNCC: 5 | RNVC: 2
5895-21-841-3607: RNCC: 6 | RNVC: 9

5 Jul 1967

5975-00-068-6767
Cable Strain Relief Bushing

000686767
SR-6P3-4: RNCC: 3 | RNVC: 2
SR-6P3-4: RNCC: 5 | RNVC: 2
324119-2: RNCC: 5 | RNVC: 2
10215944: RNCC: 5 | RNVC: 2
R6-A: RNCC: 5 | RNVC: 9
85-57: RNCC: 5 | RNVC: 9
S1326: RNCC: 5 | RNVC: 9
1523: RNCC: 5 | RNVC: 9
13170642-1: RNCC: 7 | RNVC: 2
16-119F00M00R00: RNCC: C | RNVC: 1

13 Jul 1967

5975-01-620-7033
Blank Panel

016207033
69287-1: RNCC: 3 | RNVC: 2

6 Aug 2013

5975-01-486-9035
Cable Marker Sleeve

014869035
10026-6-P2: RNCC: 3 | RNVC: 2

18 Jul 2001

5975-01-487-5490
Flexible Nonmetallic Conduit

014875490
1375-15-0002: RNCC: 3 | RNVC: 2
G95953: RNCC: D | RNVC: 9

9 Aug 2001

5975-01-487-6941
Cable Marker Sleeve

014876941
G22657: RNCC: 3 | RNVC: 2
G95986: RNCC: D | RNVC: 9

14 Aug 2001

5975-01-488-0919
Rigid Metal Conduit

014880919
5HM40038-107: RNCC: 3 | RNVC: 2

23 Aug 2001

5975-01-487-8187
Cable Marker Sleeve

014878187
G21230: RNCC: 3 | RNVC: 2
G95948: RNCC: D | RNVC: 9

20 Aug 2001

5975-01-488-1072
Flexible Metal Conduit Assembly

014881072
5HM40131-105: RNCC: 3 | RNVC: 2

23 Aug 2001

5975-01-606-1487
Electrical Grounding Plate

016061487
5030824: RNCC: 3 | RNVC: 2

9 May 2012

5975-01-605-9840
Junction Box

016059840
5338405: RNCC: 3 | RNVC: 2

2 May 2012

5975-01-606-0477
Electrical Equipment Mounting Base

016060477
9800-17700-0914: RNCC: 3 | RNVC: 2
G0071835: RNCC: 5 | RNVC: 9

4 May 2012

5975-00-176-4651
Electrical Components Tie Down Strap

001764651
HY526-1: RNCC: 3 | RNVC: 2
HY526-1: RNCC: 5 | RNVC: 9

8 Dec 1971

5975-01-487-1706
Blank Panel

014871706
069605: RNCC: 3 | RNVC: 2

26 Jul 2001

5975-01-645-3348
Eprom

016453348
74434B62VER03: RNCC: 3 | RNVC: 1

11 Jun 2015

5975-01-645-7951
Blank Panel

016457951
25R5560: RNCC: 3 | RNVC: 2

29 Jun 2015

5975-01-614-8857
Electrical Equipment Rack

016148857
701M6502: RNCC: 3 | RNVC: 2

18 Dec 2012

5975-01-615-0218
Electrical-Electronic Equipment Panel

016150218
195D5432P2: RNCC: 3 | RNVC: 2

21 Dec 2012

5975-01-617-7716
Electrical Components Tie Down Strap

016177716
BT1.5I-M0: RNCC: 3 | RNVC: 2
BT1.5I-M0: RNCC: 5 | RNVC: 2
A04081642: RNCC: 5 | RNVC: 2

3 Apr 2013

5975-01-617-2188
Electrical Equipment Cabinet

016172188
V-9805: RNCC: 3 | RNVC: 9

15 Mar 2013

5975-01-618-6324
Electrical Equipment Mounting Base

016186324
12050-3000-02: RNCC: 3 | RNVC: 2

30 Apr 2013

5975-00-962-7191
Rigid Metal Conduit

009627191
775159-59: RNCC: 3 | RNVC: 2

1 Jan 1963

5975-01-485-9014
Electrical Equipment Cabinet

014859014
4800188: RNCC: 3 | RNVC: 2

11 Jun 2001

5975-01-485-4358
Electrical Equipment Rack

014854358
106861001: RNCC: 3 | RNVC: 2

25 May 2001

5975-01-486-3006
Cable Marker Sleeve

014863006
651665: RNCC: 3 | RNVC: 2

25 Jun 2001

5975-01-486-3003
Cable Marker Sleeve

014863003
651663: RNCC: 3 | RNVC: 2

25 Jun 2001

5975-01-601-3803
Electrical Components Tie Down Strap

016013803
TY24M-9: RNCC: 3 | RNVC: 9

19 Jan 2012

5975-01-188-7458
Electrical Equipment Cabinet

011887458
110D174G1: RNCC: 3 | RNVC: 2

7 Sep 1984

5975-01-583-2693
Electrical-Electronic Equipment Chassis

015832693
AD361C: RNCC: 3 | RNVC: 2

22 Mar 2010

5975-01-586-1865
Electrical Conduit Adapter

015861865
7192971-00: RNCC: 3 | RNVC: 2

17 Jun 2010

5975-01-591-2430
Electrical-Electronic Equipment Chassis

015912430
OEM-CAE-3U02: RNCC: 3 | RNVC: 2

18 Jan 2011

5975-01-560-3112
Electrical-Electronic Equipment Chassis

015603112
510-1097-FXX-XX: RNCC: 3 | RNVC: 2
510-1097-F01-00: RNCC: 5 | RNVC: 2

24 Jan 2008

5975-01-643-5676
Monitor Holder Arm

016435676
9114-S-FM: RNCC: 3 | RNVC: 2

7 Apr 2015

5975-01-644-0870
Strain Electrical Conductor Clamp

016440870
4457892: RNCC: 3 | RNVC: 2
4457892: RNCC: 3 | RNVC: 9

22 Apr 2015

5975-00-234-0821
Electrical Equipment Cabinet

002340821
C-1588: RNCC: 3 | RNVC: 1
SFC44GRAYWRINKLE: RNCC: 3 | RNVC: 2

2 Nov 1970

5975-01-612-6990
Electrical Equipment Rack

016126990
159136SX1SLD0: RNCC: 3 | RNVC: 2
ST-694-SX1-SLD: RNCC: 5 | RNVC: 9

18 Oct 2012

5975-01-484-4998
Cable Marker Sleeve

014844998
2540806-86: RNCC: 3 | RNVC: 2
2540806-86: RNCC: 5 | RNVC: 9

30 Apr 2001

5975-01-483-9907
Cable Marker Sleeve

014839907
2540806-55: RNCC: 3 | RNVC: 2

13 Apr 2001

5975-01-619-9788
Junction Box

016199788
WJB080806: RNCC: 3 | RNVC: 2

25 Jun 2013

5975-01-632-8572
Electrical Equipment Rack

016328572
BW909A: RNCC: 3 | RNVC: 2

31 Oct 2014

5975-01-633-9435
Electrical-Electronic Equipment Panel

016339435
W68-X2Q50-30: RNCC: 3 | RNVC: 2

10 Dec 2014

5975-01-423-4154
Electrical Wall Plate

014234154
CWP8H: RNCC: 3 | RNVC: 2

26 Dec 1995

5975-01-425-7057
Cable Hanger

014257057
40785-2: RNCC: 3 | RNVC: 2

26 Feb 1996

5975-01-425-1101
Electrical Equipment Mounting Base

014251101
S665: RNCC: 3 | RNVC: 9

12 Feb 1996

5975-01-569-4961
Electrical Bushing

015694961
RL121-3: RNCC: 3 | RNVC: 2

3 Dec 2008

5975-01-569-4952
Electrical Bushing

015694952
RW309-19: RNCC: 3 | RNVC: 2

3 Dec 2008

5975-01-569-4957
Electrical Bushing

015694957
RL15-6: RNCC: 3 | RNVC: 2

3 Dec 2008

5975-01-570-2533
Electrical-Electronic Equipment Panel

015702533
360-1129-001: RNCC: 3 | RNVC: 2

18 Dec 2008

5975-01-570-4037
Electrical Equipment Cabinet

015704037
204-57454-1: RNCC: 3 | RNVC: 2

29 Dec 2008

5975-01-186-7973
Electrical Equipment Cabinet

011867973
0N002702-4: RNCC: 3 | RNVC: 2

15 Aug 1984

5975-01-642-5859
Electrical Components Tie Down Strap

016425859
28573-001: RNCC: 3 | RNVC: 2

3 Mar 2015

5975-01-641-8459
Electrical Equipment Shelf

016418459
RMS19-SA4-01: RNCC: 3 | RNVC: 9

4 Feb 2015

5975-01-642-9392
Electrical-Electronic Equipment Chassis

016429392
A3D0589-2: RNCC: 3 | RNVC: 2

16 Mar 2015

5975-01-642-2455
Electrical-Electronic Equipment Chassis

016422455
C8R10A: RNCC: 3 | RNVC: 2

19 Feb 2015

5975-01-643-3440
Electrical Equipment Rack

016433440
34200575-005: RNCC: 3 | RNVC: 2

30 Mar 2015

5975-01-642-3575
Electrical-Electronic Equipment Chassis

016423575
EB4-1U-X8G2: RNCC: 3 | RNVC: 2
EB4-1U-X8G2: RNCC: 3 | RNVC: 2

24 Feb 2015

5975-00-865-3233
Electrical Conductor Bushing

008653233
10-162581-11: RNCC: 3 | RNVC: 2

16 Oct 1967

5975-01-481-6201
Electrical-Electronic Equipment Panel

014816201
714930-1: RNCC: 3 | RNVC: 2

17 Jan 2001

5975-01-482-2173
Electrical Equipment Rack

014822173
133-340049-3: RNCC: 3 | RNVC: 2
133-340049-3: RNCC: 3 | RNVC: 9

13 Feb 2001

5975-01-514-7788
Flexible Nonmetallic Conduit

015147788
749-656-1-100.06: RNCC: 3 | RNVC: 2
5D0554-5: RNCC: 5 | RNVC: 2

4 Nov 2003

5975-01-421-8784
Electrical Equipment Rack

014218784
7334092G1: RNCC: 3 | RNVC: 2

16 Nov 1995

5975-01-420-6902
Interconnecting Box

014206902
6197 BB: RNCC: 3 | RNVC: 9

23 Oct 1995

5975-01-475-5513
Electrical Equipment Cabinet

014755513
PER800UA: RNCC: 3 | RNVC: 2

7 Jun 2000

5975-01-569-4944
Electrical Bushing

015694944
RW309-14: RNCC: 3 | RNVC: 2

3 Dec 2008

5975-01-475-3718
Electrical-Electronic Equipment Chassis

014753718
WS-C6509: RNCC: 3 | RNVC: 2
10199896: RNCC: 6 | RNVC: 9

1 Jun 2000

5975-01-136-4150
Blank Panel

011364150
9M381B12: RNCC: 3 | RNVC: 2

8 Aug 1982

5975-00-229-7412
Flexible Metal Conduit Assembly

002297412
88722: RNCC: 3 | RNVC: 2
1790-1014: RNCC: 5 | RNVC: 2
E1199-266-1014: RNCC: 5 | RNVC: 2
E1199-266-1014: RNCC: 5 | RNVC: 9

1 Jan 1963

5975-01-329-0621
Electrical-Electronic Equipment Chassis

013290621
5328162-1: RNCC: 3 | RNVC: 2
MS35389-8: RNCC: C | RNVC: 1

11 Nov 1990

5975-00-906-2293
Junction Box

009062293
9053525: RNCC: 3 | RNVC: 2
9053525: RNCC: 5 | RNVC: 1

22 Jun 1966

5975-01-479-9815
Junction Box

014799815
C99A30446-3: RNCC: 3 | RNVC: 9
C99A30446-3: RNCC: C | RNVC: 1

3 Nov 2000

5975-01-479-9960
Junction Box

014799960
C99A30446-7: RNCC: 3 | RNVC: 9
C99A30446-7: RNCC: C | RNVC: 1

3 Nov 2000

5975-01-481-6753
Flexible Metal Conduit Assembly

014816753
227733-DL0000: RNCC: 3 | RNVC: 2

18 Jan 2001

5975-01-482-2179
Electrical Equipment Rack

014822179
133-340049-13: RNCC: 3 | RNVC: 2
133-340049-13: RNCC: 3 | RNVC: 9

13 Feb 2001

5975-01-533-9071
Electrical-Electronic Equipment Panel

015339071
16F20236-1: RNCC: 3 | RNVC: 2

29 Sep 2005

5975-01-460-9235
Chassis Electrical

014609235
11441967: RNCC: 3 | RNVC: 2

20 Nov 1998

5975-01-204-4476
Electrical Equipment Mounting Base

012044476
206738-0101: RNCC: 3 | RNVC: 2

27 Mar 1985

5975-01-160-7993
Conduit Cover Plate

011607993
2890846: RNCC: 3 | RNVC: 2
2890846: RNCC: 5 | RNVC: 2
2890846: RNCC: 5 | RNVC: 9

27 Aug 1983

5975-00-243-5216
Flexible Metal Conduit

002435216
1150-16ALT2: RNCC: 3 | RNVC: 2
MILC6136TYPE1: RNCC: 4 | RNVC: 1

1 Jan 1963

5975-01-314-4975
Electrical-Electronic Equipment Chassis

013144975
620400: RNCC: 3 | RNVC: 9

31 Jan 1990

5975-01-566-3223
Cable Hanger

015663223
L28320G01: RNCC: 3 | RNVC: 2

27 Aug 2008

5975-01-478-4956
Junction Box Assembly

014784956
KC84351-001: RNCC: 3 | RNVC: 2

14 Sep 2000

5975-01-613-2177
Me Conduit Assembly

016132177
227681-DL0000: RNCC: 3 | RNVC: 2

1 Nov 2012

5975-01-616-6443
Junction Box Cover

016166443
8613570: RNCC: 3 | RNVC: 9

22 Feb 2013

5975-01-532-2109
Electrical Equipment Cabinet

015322109
002110-0102: RNCC: 3 | RNVC: 2

2 Aug 2005

5975-01-456-1384
Junction Box Assembly

014561384
068010: RNCC: 3 | RNVC: 2

2 Jun 1998

5975-01-455-7648
Raceway Cover

014557648
8902-4: RNCC: 3 | RNVC: 2

14 May 1998

5975-01-459-6363
Electrical Equipment Mounting Base

014596363
D3349B: RNCC: 3 | RNVC: 2

8 Oct 1998

5975-01-502-3250
Electrical Equipment Rack

015023250
5HU50400-115: RNCC: 3 | RNVC: 2

31 Oct 2002

5975-01-571-5156
Electrical Components Tie Down Strap

015715156
PLT8H-C0: RNCC: 3 | RNVC: 2
10300105: RNCC: 6 | RNVC: 9

5 Feb 2009

5975-00-241-3656
Electrical Box Connector

002413656
CGB498: RNCC: 3 | RNVC: 1
SR12510: RNCC: 5 | RNVC: 9

1 Jan 1963

5975-01-565-5080
Electrical Fitting Mounting Base

015655080
5140007-1: RNCC: 3 | RNVC: 2

28 Jul 2008

5975-01-539-5989
Electrical Conduit Coupling Nut

015395989
ACN LE-T40-7991: RNCC: 3 | RNVC: 2
MIL-H-21367/5 ITEM 14: RNCC: 5 | RNVC: 2
M21367/2-08: RNCC: 5 | RNVC: 2
M21367/5-14: RNCC: 5 | RNVC: 2

26 Apr 2006

5975-01-534-8396
Electrical-Electronic Equipment Chassis

015348396
187774-1: RNCC: 3 | RNVC: 2

3 Nov 2005

5975-01-536-7392
Electrical-Electronic Equipment Chassis

015367392
361D813G01: RNCC: 3 | RNVC: 2
361D813G01: RNCC: 3 | RNVC: 9

12 Jan 2006

5975-01-537-0869
Cable Hanger

015370869
MAS-7200-CBLMGMT: RNCC: 3 | RNVC: 2

25 Jan 2006

5975-01-603-8255
Blank Port Plate

016038255
758406-3: RNCC: 3 | RNVC: 2

17 Mar 2012

5975-01-450-2709
Electrical Equipment Mounting Base

014502709
653-9015-002: RNCC: 3 | RNVC: 2

31 Oct 1997

5975-01-452-5797
Electrical Equipment Mounting Base

014525797
8026818: RNCC: 3 | RNVC: 2

30 Jan 1998

5975-01-451-9497
Cover Assembly Junction Box

014519497
3351133-1: RNCC: 3 | RNVC: 2

9 Jan 1998

5975-01-211-1955
Electrical Equipment Mounting Base

012111955
92354-3: RNCC: 3 | RNVC: 2
4011646: RNCC: 5 | RNVC: 2
4011646: RNCC: 5 | RNVC: 2
92354-3: RNCC: 5 | RNVC: 9
4011646: RNCC: 7 | RNVC: 2

22 Jun 1985

5975-01-213-0801
Electrical Components Tie Down Strap

012130801
TY50: RNCC: 3 | RNVC: 2
926928001: RNCC: 5 | RNVC: 2

22 Jul 1985

5975-01-320-7440
Electrical-Electronic Equipment Chassis

013207440
717612545-149: RNCC: 3 | RNVC: 2

2 Jun 1990

5975-01-023-8400
Clamping Unit

010238400
HC-10-3: RNCC: 3 | RNVC: 9

26 Jun 1976

5975-01-425-7510
Electrical Components Tie Down Strap

014257510
PLT2I-Q0: RNCC: 3 | RNVC: 2

27 Feb 1996

5975-01-571-2772
Electrical-Electronic Equipment Chassis

015712772
988-1358-001: RNCC: 3 | RNVC: 2

29 Jan 2009

5975-01-572-1626
Electronic Junction Rack

015721626
RR1061-17: RNCC: 3 | RNVC: 2

2 Mar 2009

5975-01-571-1509
Electrical-Electronic Equipment Panel

015711509
986-3886-001: RNCC: 3 | RNVC: 2

26 Jan 2009

5975-01-571-5960
Blank Panel

015715960
E7731A: RNCC: 3 | RNVC: 2
E7731A: RNCC: 3 | RNVC: 9

10 Feb 2009

5975-01-571-6141
Electrical-Electronic Equipment Chassis

015716141
40300111-001: RNCC: 3 | RNVC: 2

10 Feb 2009

5975-01-572-0456
Electrical-Electronic Equipment Chassis

015720456
77447500-009: RNCC: 3 | RNVC: 2

25 Feb 2009

5975-01-572-6694
Electrical Equipment Cabinet

015726694
NST-525UF: RNCC: 3 | RNVC: 2

19 Mar 2009

5975-01-601-4375
Electronic Equipment Mounting Tray

016014375
06-01896511: RNCC: 3 | RNVC: 2

19 Jan 2012

5975-01-446-2776
Electrical Cable Nipple

014462776
2810-12-0012: RNCC: 3 | RNVC: 2
331-103: RNCC: 5 | RNVC: 2

27 Jun 1997

5975-01-446-5405
Cable Strain Relief Bushing

014465405
CG90-5050: RNCC: 3 | RNVC: 9
CG90-5050: RNCC: C | RNVC: 1

9 Jul 1997

5975-01-498-6596
Rigid Metal Conduit Assembly

014986596
5HB71101-207: RNCC: 3 | RNVC: 2

29 Jun 2002

5975-01-499-1553
Electrical Components Tie Down Strap

014991553
10249-3109: RNCC: 3 | RNVC: 2

15 Jul 2002

5975-01-553-6850
Electronic Equipment Mounting Tray

015536850
200-99814-101: RNCC: 3 | RNVC: 2

23 Jul 2007

5975-01-569-4951
Electrical Bushing

015694951
RL121-2: RNCC: 3 | RNVC: 2

3 Dec 2008

5975-01-570-5588
Electrical-Electronic Equipment Panel

015705588
SF-SE-10H-240: RNCC: 3 | RNVC: 2

6 Jan 2009

5975-01-570-4069
Electrical Equipment Cabinet Closeout

015704069
204-57463-9: RNCC: 3 | RNVC: 2

29 Dec 2008

5975-01-571-1505
Electrical-Electronic Equipment Panel

015711505
988-4464-001: RNCC: 3 | RNVC: 2

26 Jan 2009

5975-01-571-3823
Stake Kit

015713823
ES-162P3: RNCC: 3 | RNVC: 2

2 Feb 2009

5975-01-570-9940
Electrical-Electronic Equipment Chassis

015709940
10122531-102: RNCC: 3 | RNVC: 2

21 Jan 2009

5975-01-571-0393
Electrical-Electronic Equipment Chassis

015710393
IPC-610BP-00XFCE: RNCC: 3 | RNVC: 2

22 Jan 2009

5975-01-570-9900
Stuffing Tube

015709900
MCG-29R: RNCC: 3 | RNVC: 2

21 Jan 2009

5975-01-570-9932
Electrical-Electronic Equipment Panel

015709932
10115719-102: RNCC: 3 | RNVC: 2

21 Jan 2009

5975-01-441-0063
Electrical-Electronic Equipment Chassis

014410063
BA356-KC: RNCC: 3 | RNVC: 2

30 Jan 1997

5975-01-631-8519
Electrical Equipment Cabinet

016318519
902205-803: RNCC: 3 | RNVC: 2

29 Sep 2014

5975-01-632-8764
Conduit Outlet Cover

016328764
T70WC2IW: RNCC: 3 | RNVC: 2

31 Oct 2014

5975-01-633-1083
Electrical Box Connector

016331083
WIC-CP1-56: RNCC: 3 | RNVC: 2

7 Nov 2014

5975-01-322-3677
Electrical Equipment Mounting Base

013223677
13029771: RNCC: 3 | RNVC: 2

3 Jul 1990

5975-01-674-7380
Electrical Cable Protector

016747380
AB3917A124AA: RNCC: 3 | RNVC: 2
23228659: RNCC: 5 | RNVC: 2
7423228659: RNCC: 5 | RNVC: 2

9 Aug 2018

5975-01-674-5591
Junction Box

016745591
433.150.150: RNCC: 3 | RNVC: 2

1 Aug 2018

5975-01-674-5542
Stuffing Tube

016745542
453.014.010: RNCC: 3 | RNVC: 2

1 Aug 2018

5975-01-674-6864
Insulation Entry

016746864
IEK-14: RNCC: 3 | RNVC: 2

7 Aug 2018

5975-01-569-8117
Electrical Standardized Components Case Section

015698117
204-32736-5: RNCC: 3 | RNVC: 2

9 Dec 2008

5975-01-436-8774
Electrical Equipment Rack

014368774
B-3000-724: RNCC: 3 | RNVC: 2
62828-90116-13: RNCC: 5 | RNVC: 2

30 Sep 1996

5975-01-631-0509
Electrical-Electronic Equipment Chassis

016310509
333315-001: RNCC: 3 | RNVC: 2

27 Aug 2014

5975-01-630-5561
Electrical-Electronic Equipment Panel

016305561
2853239-2: RNCC: 3 | RNVC: 2
2853239: RNCC: D | RNVC: 9

8 Aug 2014

5975-01-631-3645
Electrical Equipment Mounting Base

016313645
68A810226-2001: RNCC: 3 | RNVC: 2

10 Sep 2014

5975-01-329-5722
Electrical Equipment Mounting Base

013295722
MI585356: RNCC: 3 | RNVC: 2

19 Nov 1990

5975-00-931-2745
End Cap

009312745
439305-1: RNCC: 3 | RNVC: 2

14 Sep 1966

5975-00-982-0154
Electrical Components Tie Down Strap

009820154
89104-1: RNCC: 3 | RNVC: 2

14 Oct 1966

5975-01-672-4109
Electrical-Electronic Equipment Chassis

016724109
752-8799-002: RNCC: 3 | RNVC: 2

1 May 2018

5975-01-673-3147
Electrical Equipment Drawer

016733147
H409925-10: RNCC: 3 | RNVC: 2

11 Jun 2018

5975-01-672-5844
Electrical Equipment Mounting Base

016725844
7902AV81130-3: RNCC: 3 | RNVC: 2

8 May 2018

5975-01-567-9189
Electrical Tie Down Mounting Base

015679189
NMCSB7000UG2NH3: RNCC: 3 | RNVC: 2

10 Oct 2008

5975-01-435-3325
Cable Terminal Chamber

014353325
352058-3: RNCC: 3 | RNVC: 2

21 Aug 1996

5975-01-567-8562
Electrical Box Connector

015678562
S25252: RNCC: 3 | RNVC: 9
S25252: RNCC: C | RNVC: 1

8 Oct 2008

5975-01-596-9814
Electrical Support

015969814
5158T28G01: RNCC: 3 | RNVC: 2

25 May 2011

5975-00-268-5772
Flexible Metal Conduit Assembly

002685772
5116427-30: RNCC: 3 | RNVC: 2
5116427-30: RNCC: 5 | RNVC: 9

13 Jul 1973

5975-01-670-8142
Electrical Equipment Shelf

016708142
7-511113586-103: RNCC: 3 | RNVC: 2

7 Mar 2018

5975-01-565-5082
Electrical Fitting Mounting Base

015655082
5140004-1: RNCC: 3 | RNVC: 2

28 Jul 2008

5975-01-565-8437
Electronic Junction Rack

015658437
6651-1100-050: RNCC: 3 | RNVC: 2

8 Aug 2008

5975-01-566-6626
Electrical-Electronic Equipment Chassis

015666626
5119400-2: RNCC: 3 | RNVC: 2

5 Sep 2008

5975-01-396-5594
Electrical Equipment Foot

013965594
111023: RNCC: 3 | RNVC: 2

21 Sep 1994

5975-01-249-9914
Conduit Outlet Cover

012499914
05X0004-0205: RNCC: 3 | RNVC: 2
05X0004-0205: RNCC: 5 | RNVC: 9

21 Feb 1987

5975-01-566-3305
Fanning Strip

015663305
525-11752-522: RNCC: 3 | RNVC: 2

27 Aug 2008

5975-01-567-5641
Electrical Equipment Mounting Base

015675641
G1-59-6001-800: RNCC: 3 | RNVC: 2

30 Sep 2008

5975-01-596-2951
Blank Panel

015962951
401855-02: RNCC: 3 | RNVC: 2

13 May 2011

5975-01-597-0122
Ground Rod

015970122
E107302: RNCC: 3 | RNVC: 2

25 May 2011

5975-01-318-9909
Electrical Components Tie Down Strap

013189909
600002-116-001: RNCC: 3 | RNVC: 2
600002-116-001: RNCC: 5 | RNVC: 9

29 Apr 1990

5975-01-668-3494
Raceway Cover

016683494
FRRASC6YL: RNCC: 3 | RNVC: 2
FRRASC6YL: RNCC: 5 | RNVC: 9

20 Nov 2017

5975-01-670-8137
Electrical Equipment Shelf

016708137
7-511115240-13: RNCC: 3 | RNVC: 2

7 Mar 2018

5975-01-669-0727
Mounting Plate

016690727
H292970-100: RNCC: 3 | RNVC: 2
H292970-100: RNCC: 5 | RNVC: 2

20 Dec 2017

5975-01-669-5413
Guide Rail

016695413
NM60-L800-P3-C40-D40: RNCC: 3 | RNVC: 2

11 Jan 2018

5975-01-669-7938
Electrical Equipment Drawer

016697938
780291-01: RNCC: 3 | RNVC: 2

22 Jan 2018

5975-01-669-0723
Mounting Plate

016690723
H292967-DUB: RNCC: 3 | RNVC: 2
60223248-00: RNCC: 5 | RNVC: 2

20 Dec 2017

5975-01-392-5512
Rigid Metal Conduit Assembly

013925512
5493230-49: RNCC: 3 | RNVC: 2

1 Jul 1994

5975-01-392-9703
Electrical-Electronic Equipment Chassis

013929703
14000666: RNCC: 3 | RNVC: 2

11 Jul 1994

5975-01-393-8249
Electrical-Electronic Equipment Chassis

013938249
62000687-000: RNCC: 3 | RNVC: 2

27 Jul 1994

5975-01-247-2119
Electrical Components Tie Down Strap

012472119
GTR112G10N: RNCC: 3 | RNVC: 2
10333574: RNCC: 6 | RNVC: 9

29 Dec 1986

5975-01-413-7474
Electronic Equipment Mounting Tray

014137474
78-8041-7720-8: RNCC: 3 | RNVC: 9

22 May 1995

5975-01-415-8040
Electrical-Electronic Equipment Chassis

014158040
DMR9315#: RNCC: 3 | RNVC: 9
DMR9315: RNCC: 5 | RNVC: 2

6 Jul 1995

5975-01-244-0941
Electrical Wall Plate

012440941
600-A10447: RNCC: 3 | RNVC: 2

7 Nov 1986

5975-01-594-3193
Electrical Components Tie Down Strap

015943193
435-1169-630: RNCC: 3 | RNVC: 2

25 Apr 2011

5975-01-594-3184
Electrical Components Tie Down Strap

015943184
M90390-19: RNCC: 3 | RNVC: 2

25 Apr 2011

5975-01-594-6889
Electrical Equipment Mounting Base

015946889
MT4-12316-102: RNCC: 3 | RNVC: 2
114784-001: RNCC: 7 | RNVC: 2

25 Apr 2011

5975-00-296-3340
Electrical Box Connector

002963340
DB6716: RNCC: 3 | RNVC: 2
8328107: RNCC: 3 | RNVC: 2

1 Jan 1963

5975-00-939-5632
Electrical Box Connector

009395632
7486: RNCC: 3 | RNVC: 2
XC406: RNCC: 3 | RNVC: 2
259: RNCC: 3 | RNVC: 2
2108: RNCC: 5 | RNVC: 2
534: RNCC: 5 | RNVC: 2
416: RNCC: 5 | RNVC: 9
24-200: RNCC: 5 | RNVC: 9
1007: RNCC: 5 | RNVC: 9
713: RNCC: 5 | RNVC: 9

22 Nov 1965

5975-01-666-8074
Electrical-Electronic Equipment Chassis

016668074
IPC-602P3-30ZB: RNCC: 3 | RNVC: 2

21 Sep 2017

5975-01-665-3851
Electrical Equipment Mounting Base

016653851
TT-01-406080A-001: RNCC: 3 | RNVC: 2
40092289: RNCC: 5 | RNVC: 2

27 Jul 2017

5975-01-665-5212
Electronic Equipment Mounting Tray

016655212
UHK81282-1: RNCC: 3 | RNVC: 2

2 Aug 2017

5975-01-665-6514
External Elbow Raceway

016656514
C58: RNCC: 3 | RNVC: 2

8 Aug 2017

5975-01-667-1228
Cable Collar

016671228
63901: RNCC: 3 | RNVC: 2

4 Oct 2017

5975-01-666-6308
Cable Rack Extension

016666308
T1U-200-CMA: RNCC: 3 | RNVC: 2

14 Sep 2017

5975-01-667-3070
Electrical Equipment Rack

016673070
BW896A: RNCC: 3 | RNVC: 2
L-IN-1-RK: RNCC: 5 | RNVC: 2

11 Oct 2017

5975-01-667-1390
Electrical Equipment Rack

016671390
OG-UPS1000-17: RNCC: 3 | RNVC: 2

4 Oct 2017

5975-01-667-8766
Electrical Components Tie Down Strap

016678766
3955T85: RNCC: 3 | RNVC: 2

2 Nov 2017

5975-01-562-1578
Electrical Equipment Rack

015621578
RR1079-1: RNCC: 3 | RNVC: 2

1 Apr 2008

5975-01-390-6858
Electrical-Electronic Equipment Chassis

013906858
8531-RM: RNCC: 3 | RNVC: 2
652/4/11350/001: RNCC: 5 | RNVC: 2

24 May 1994

5975-01-238-9678
Junction Box

012389678
5055280-1: RNCC: 3 | RNVC: 2
5055280-1: RNCC: 5 | RNVC: 9

23 Aug 1986

5975-01-237-2021
Electrical Equipment Cabinet

012372021
57977-40005-2: RNCC: 3 | RNVC: 2

26 Jul 1986

5975-01-592-4220
Junction Box

015924220
P070-08: RNCC: 3 | RNVC: 2

7 Mar 2011

5975-01-592-1171
Electronic Equipment Mounting Tray

015921171
M075039: RNCC: 3 | RNVC: 2
M075039: RNCC: 3 | RNVC: 9

22 Feb 2011

5975-01-592-3869
Blank Panel

015923869
D789F: RNCC: 3 | RNVC: 2
14709A-6: RNCC: C | RNVC: 1

4 Mar 2011

5975-01-592-7653
Electrical-Electronic Equipment Chassis

015927653
622-9669-001: RNCC: 3 | RNVC: 2
622-9669-001: RNCC: 5 | RNVC: 2

18 Mar 2011

5975-01-593-5650
Electrical Equipment Cabinet

015935650
BS-2000-400-905: RNCC: 3 | RNVC: 2

11 Apr 2011

5975-01-592-1169
Electronic Equipment Mounting Tray

015921169
M075040: RNCC: 3 | RNVC: 2
M075040: RNCC: 3 | RNVC: 9

22 Feb 2011

5975-00-280-3857
Stuffing Tube Packing Nut

002803857
04431: RNCC: 3 | RNVC: 2

1 Jan 1960

5975-00-280-3888
Electrical Box Connector

002803888
DHF9: RNCC: 3 | RNVC: 2

1 Jan 1963

5975-01-301-5283
Cable Carrier Assy

013015283
10496700-02: RNCC: 3 | RNVC: 9

31 May 1989

5975-01-302-2107
Electrical Components Tie Down Strap

013022107
PLT1.5I-C20: RNCC: 3 | RNVC: 2

10 Jun 1989

5975-01-303-6766
Electrical Components Tie Down Strap

013036766
696-40527-1-2: RNCC: 3 | RNVC: 2
696-40527-1-2-C: RNCC: 5 | RNVC: 2

4 Jul 1989

5975-00-931-7374
Junction Box

009317374
170-40804-9: RNCC: 3 | RNVC: 2
170-40804-9: RNCC: 5 | RNVC: 9

19 Sep 1966

5975-01-693-3909
Cable Marker Sleeve

016933909
SS7074-1923: RNCC: 3 | RNVC: 2

9 Feb 2021

5975-01-663-4364
Electrical Equipment Rack

016634364
ACS-4430-RM-19=: RNCC: 3 | RNVC: 2

10 May 2017

5975-01-663-2553
Electrical-Electronic Equipment Chassis

016632553
ASR-9010-SYS: RNCC: 3 | RNVC: 2

3 May 2017

5975-01-692-4064
Junction Box

016924064
02-Y01-16-244-01: RNCC: 3 | RNVC: 2

11 Dec 2020

5975-01-692-4893
Electrical Equipment Rack

016924893
DRT1183C-000: RNCC: 3 | RNVC: 2

17 Dec 2020

5975-01-692-7225

7 Jan 2021

5975-01-664-6613
Electrical-Electronic Equipment Chassis

016646613
IPC-610MB-00XHE: RNCC: 3 | RNVC: 2

29 Jun 2017

5975-01-664-4005
Electrical Standardized Components Case

016644005
PWR CASE-S/MCM-01: RNCC: 3 | RNVC: 9
PWR CASE-S/MCM-01: RNCC: 5 | RNVC: 2
PWR CASE-S/MCM-01: RNCC: 5 | RNVC: 9

19 Jun 2017

5975-01-664-7067
Electrical Equipment Rack

016647067
1037-000001-01: RNCC: 3 | RNVC: 2

30 Jun 2017

5975-01-664-7576
Electrical Components Tie Down Strap

016647576
302R502-4: RNCC: 3 | RNVC: 2

5 Jul 2017

5975-01-664-8693
Electrical Components Tie Down Strap

016648693
111-91819: RNCC: 3 | RNVC: 2
321-4476: RNCC: 5 | RNVC: 2
70107775: RNCC: 5 | RNVC: 2
111-91819-T18R-PA66VO-WH: RNCC: 5 | RNVC: 2
SUB37000592421: RNCC: 5 | RNVC: 2

10 Jul 2017

5975-01-600-8677
Electrical Equipment Foot

016008677
S232002-101: RNCC: 3 | RNVC: 2

22 Dec 2011

5975-01-601-3231
Electrical Equipment Cabinet

016013231
VNXRACK-40US: RNCC: 3 | RNVC: 2

19 Jan 2012

5975-01-601-6633
Electrical-Electronic Equipment Chassis

016016633
S8-CHASSIS: RNCC: 3 | RNVC: 2

19 Jan 2012

5975-01-601-6595
Drives Emc Rack

016016595
VNX53D153015: RNCC: 3 | RNVC: 2

19 Jan 2012

5975-01-560-7833
Cable Terminal Chamber Mounting Kit

015607833
QTPET MTGKIT: RNCC: 3 | RNVC: 2

12 Feb 2008

5975-01-560-4844
Electrical Equipment Rack

015604844
16U90A52-7: RNCC: 3 | RNVC: 2

31 Jan 2008

5975-01-235-2833
Blank Panel

012352833
57977-40065-2: RNCC: 3 | RNVC: 2

27 Jun 1986

5975-01-591-2433
Electrical-Electronic Equipment Chassis

015912433
0235A297: RNCC: 3 | RNVC: 2

18 Jan 2011

5975-00-280-3318
Electrical Conduit Coupling Nut

002803318
A25810: RNCC: 3 | RNVC: 2

1 Jan 1963

5975-01-301-3684
Flexible Metal Conduit

013013684
E.F. 3/4BLACK SMALL CARTON: RNCC: 3 | RNVC: 2
781342-36022: RNCC: 3 | RNVC: 2
8900-0311-001: RNCC: 5 | RNVC: 2

27 May 1989

5975-01-300-5650
Electrical Conduit Adapter

013005650
305123: RNCC: 3 | RNVC: 2

17 May 1989

5975-01-301-0041
Ad Controller

013010041
59-100: RNCC: 3 | RNVC: 2

23 May 1989

5975-01-690-6242
Electrical Box Connector

016906242
1169: RNCC: 3 | RNVC: 2
1169: RNCC: 5 | RNVC: 2

24 Aug 2020

5975-01-690-6065
Rigid Nonmetallic Conduit

016906065
F1X2LG6: RNCC: 3 | RNVC: 2

21 Aug 2020

5975-01-690-8334
Electrical Tie Down Mounting Base

016908334
ABM3H-AT-L: RNCC: 3 | RNVC: 2

3 Sep 2020

5975-01-600-0347
Electrical Tie Down Mounting Base

016000347
C9N-039: RNCC: 3 | RNVC: 2
C9N-039: RNCC: 5 | RNVC: 2

3 Nov 2011

5975-01-600-2581
Flexible Metal Conduit Assembly

016002581
254090: RNCC: 3 | RNVC: 2

18 Nov 2011

5975-01-397-1331
Electrical Equipment Rack

013971331
290-118918-01: RNCC: 3 | RNVC: 2
MT6911FSQ131: RNCC: 3 | RNVC: 2

4 Oct 1994

5975-01-389-4415
Electrical-Electronic Equipment Chassis

013894415
1219738-201: RNCC: 3 | RNVC: 2
80400/21202: RNCC: 5 | RNVC: 9
1219738-201: RNCC: 5 | RNVC: 9

25 Apr 1994

5975-01-397-7759
Rigid Metal Conduit

013977759
1310-0101-15: RNCC: 3 | RNVC: 2
1310-0101-15: RNCC: 5 | RNVC: 9

20 Oct 1994

5975-01-406-2952
Electrical Conduit Elbow

014062952
UA9AEB: RNCC: 3 | RNVC: 9
00034481227014: RNCC: 5 | RNVC: 9

29 Dec 1994

5975-01-233-6635
Electrical Equipment Cabinet

012336635
522-1564-005: RNCC: 3 | RNVC: 9
CY-25232/WLR-1: RNCC: 5 | RNVC: 2

1 Jun 1986

5975-01-234-6645
Wiring Duct

012346645
LD3BR6-A: RNCC: 3 | RNVC: 2

18 Jun 1986

5975-01-590-1694
Electrical Equipment Mounting Base

015901694
M103001: RNCC: 3 | RNVC: 2
M103001: RNCC: 3 | RNVC: 9

22 Nov 2010

5975-00-296-0017
Conduit Outlet Cover

002960017
DS32G: RNCC: 3 | RNVC: 1

1 Jan 1963

5975-00-296-5040
Electrical Box Connector

002965040
7124820PT7: RNCC: 3 | RNVC: 2
RC1201: RNCC: 3 | RNVC: 2
9784-28: RNCC: 5 | RNVC: 9
258-5678: RNCC: 5 | RNVC: 9
9784-28: RNCC: C | RNVC: 1

1 Jan 1963

5975-01-687-9270
Electrical Equipment Rack

016879270
RS702030: RNCC: 3 | RNVC: 2

24 Apr 2020

5975-01-688-0616
Shop Set Installation Electrical Kit

016880616
950-03878: RNCC: 3 | RNVC: 2

1 May 2020

5975-01-687-7203
Electrical Equipment Mounting Base

016877203
519192-001: RNCC: 3 | RNVC: 2

15 Apr 2020

5975-01-690-4411
Electrical-Electronic Equipment Chassis

016904411
IPC-7130-00XE: RNCC: 3 | RNVC: 2

12 Aug 2020

5975-01-598-4045
Base Ground Rod

015984045
60X: RNCC: 3 | RNVC: 9

28 Jul 2011

5975-01-599-1829
Eprom

015991829
74434B65VERTBE: RNCC: 3 | RNVC: 1

14 Sep 2011

5975-01-386-2281
Plug-In Busduct

013862281
DFVAN-1368-800A: RNCC: 3 | RNVC: 2

31 Jan 1994

5975-01-387-7627
Electrical Equipment Rack

013877627
P9000-10: RNCC: 3 | RNVC: 9

11 Mar 1994

5975-01-585-8436
Electrical Equipment Mounting Base

015858436
108333: RNCC: 3 | RNVC: 2

8 Jun 2010

5975-01-588-9112
Blank Panel

015889112
905213-057: RNCC: 3 | RNVC: 2

8 Oct 2010

5975-01-588-7090
Electrical-Electronic Equipment Chassis

015887090
AJ805A: RNCC: 3 | RNVC: 9
2312SA: RNCC: 5 | RNVC: 9
MSA2312SA: RNCC: 5 | RNVC: 9

30 Sep 2010

5975-01-684-6583
Electrical Equipment Rack

016846583
10141-0018: RNCC: 3 | RNVC: 2

12 Nov 2019

5975-01-685-0165
Electrical-Electronic Equipment Chassis

016850165
12109-3200-99: RNCC: 3 | RNVC: 2

25 Nov 2019

5975-01-684-7806
Electrical Equipment Rack

016847806
590033: RNCC: 3 | RNVC: 9

15 Nov 2019

5975-01-685-1980
Electrical Equipment Cabinet

016851980
3001F99G07: RNCC: 3 | RNVC: 1

5 Dec 2019

5975-01-687-4013
Metallic Raceway

016874013
74A551133-1001: RNCC: 3 | RNVC: 2

31 Mar 2020

5975-01-685-8730
Mounting Plate

016858730
K10055800-501: RNCC: 3 | RNVC: 2

17 Jan 2020

5975-01-686-0345
Electrical-Electronic Equipment Chassis

016860345
RFE23050610-502: RNCC: 3 | RNVC: 2
RFE23050610-502: RNCC: 3 | RNVC: 9

27 Jan 2020

5975-01-685-8352
Mounting Plate

016858352
K10056019-1: RNCC: 3 | RNVC: 2

15 Jan 2020

5975-01-687-2310
Electrical-Electronic Equipment Chassis

016872310
SCD00800-9: RNCC: 3 | RNVC: 2

24 Mar 2020

5975-01-687-2991
Junction Box

016872991
844E2160-3: RNCC: 3 | RNVC: 2

26 Mar 2020

5975-01-596-9193
Electronic Junction Rack

015969193
N5230C-1CM: RNCC: 3 | RNVC: 2
N5230C-1CM: RNCC: 3 | RNVC: 9
91912021: RNCC: 5 | RNVC: 2

25 May 2011

5975-01-597-4766
Electrical Equipment Rack

015974766
7250732: RNCC: 3 | RNVC: 2

9 Jun 2011

5975-01-597-6886
Spec Sas Raid Nclos

015976886
CA80766: RNCC: 3 | RNVC: 2

20 Jun 2011

5975-01-400-4011
Electrical Equipment Mounting Base

014004011
490754-2: RNCC: 3 | RNVC: 2
658/4/04550/001: RNCC: 5 | RNVC: 2

15 Dec 1994

5975-01-225-6521
Wiring Duct

012256521
LD5BG6-A: RNCC: 3 | RNVC: 2

6 Feb 1986

5975-01-227-2643
Electrical Equipment Cabinet

012272643
110D172G1: RNCC: 3 | RNVC: 2

1 Mar 1986

5975-01-229-0209
Junction Box Cover

012290209
176C2237: RNCC: 3 | RNVC: 2

24 Mar 1986

5975-01-584-9977
Electrical Components Tie Down Strap

015849977
PLT1M-C-3: RNCC: 3 | RNVC: 2

13 May 2010

5975-01-586-2888
Electrical-Electronic Equipment Chassis

015862888
R003677-01: RNCC: 3 | RNVC: 9

22 Jun 2010

5975-01-586-5851
Nonmetallic Raceway

015865851
42-122-24A: RNCC: 3 | RNVC: 2
AVTRAC 480R AC: RNCC: 3 | RNVC: 2

6 Jul 2010

5975-01-586-9711
Electrical Equipment Rack

015869711
5HU50100-117: RNCC: 3 | RNVC: 2

20 Jul 2010

5975-01-586-5704
Electrical-Electronic Equipment Chassis

015865704
2202-04: RNCC: 3 | RNVC: 2

3 Jul 2010

5975-01-248-2083
Cable Hanger

012482083
S03032001: RNCC: 3 | RNVC: 2

20 Jan 1987

5975-01-296-8900
Electrical Equipment Cabinet

012968900
T7321L-816TANDT7331L-816T: RNCC: 3 | RNVC: 2

25 Mar 1989

5975-01-297-1349
Junction Box

012971349
DAA3222D827-037: RNCC: 3 | RNVC: 2

29 Mar 1989

5975-01-679-4328
Electrical-Electronic Equipment Chassis

016794328
EX-4PST-RMK-DPX: RNCC: 3 | RNVC: 2
EX-4PST-RMK-DPX: RNCC: 5 | RNVC: 2

25 Mar 2019

5975-01-678-9962
Electrical-Electronic Equipment Chassis

016789962
MX104-MX5-AC: RNCC: 3 | RNVC: 2
MX104-MX5-AC: RNCC: 5 | RNVC: 2

6 Mar 2019

5975-01-679-4304
Electrical-Electronic Equipment Chassis

016794304
EX-RMK2: RNCC: 3 | RNVC: 2
EX-RMK2: RNCC: 5 | RNVC: 2

25 Mar 2019

5975-01-680-0534
Electrical-Electronic Equipment Chassis

016800534
783588-01: RNCC: 3 | RNVC: 2
R106963-01: RNCC: 7 | RNVC: 2

17 Apr 2019

5975-01-681-0050
Electronic Equipment Mounting Tray

016810050
403629-01: RNCC: 3 | RNVC: 2

31 May 2019

5975-01-680-9220
Electrical-Electronic Equipment Chassis

016809220
MPS-1914-M-N-A-D-P: RNCC: 3 | RNVC: 2

28 May 2019

5975-01-681-8851
Flexible Metal Conduit

016818851
233-9494: RNCC: 3 | RNVC: 2

11 Jul 2019

5975-01-682-1082
Electronic Equipment Mounting Tray

016821082
805- 10870-001: RNCC: 3 | RNVC: 2

23 Jul 2019

5975-01-682-5502
Electrical-Electronic Equipment Chassis

016825502
SNA-DC2/35: RNCC: 3 | RNVC: 9

13 Aug 2019

5975-01-684-3368
Grounding Kit

016843368
DK 7829.150: RNCC: 3 | RNVC: 2
PS330-100057-01: RNCC: 5 | RNVC: 2

30 Oct 2019

5975-01-594-6890
Electrical Equipment Mounting Base

015946890
MT4-4315-104: RNCC: 3 | RNVC: 2

25 Apr 2011

5975-01-595-5358
Prom Flash

015955358
216C9885VER1.06: RNCC: 3 | RNVC: 1
WF1M32B-100HM3: RNCC: 5 | RNVC: 1

2 May 2011

5975-01-595-0680
Insulator Bracket

015950680
53634893: RNCC: 3 | RNVC: 2

25 Apr 2011

5975-01-594-9991
Electrical Wall Plate

015949991
107991143: RNCC: 3 | RNVC: 2

25 Apr 2011

5975-01-419-2060
Electrical-Electronic Equipment Chassis

014192060
C200H-BC081-V2: RNCC: 3 | RNVC: 2

15 Sep 1995

5975-01-419-6602
Junction Box

014196602
1500-JB: RNCC: 3 | RNVC: 9
1500-JB: RNCC: 5 | RNVC: 2

27 Sep 1995

5975-01-228-8885
Junction Box Assembly

012288885
176C2534: RNCC: 3 | RNVC: 2

22 Mar 1986

5975-01-398-4672
Navig Mounting Tray

013984672
7020479-901: RNCC: 3 | RNVC: 2
7020479-901: RNCC: 5 | RNVC: 9

4 Nov 1994

5975-01-222-7153
Rear Assembly Panel

012227153
253-42239: RNCC: 3 | RNVC: 9

16 Dec 1985

5975-01-666-6029
Rigid Metal Conduit

016666029
COML: RNCC: 3 | RNVC: 2

13 Sep 2017

5975-01-666-4696
Electrical-Electronic Equipment Chassis

016664696
DSX4-D24: RNCC: 3 | RNVC: 9

7 Sep 2017

5975-01-666-2460
Electrical-Electronic Equipment Chassis

016662460
DSX4R-24MB40-D24: RNCC: 3 | RNVC: 9

29 Aug 2017

5975-00-280-9525
Electrical Conduit Coupling Nut

002809525
118-1-0750: RNCC: 3 | RNVC: 2
118-1-0750: RNCC: 5 | RNVC: 2

1 Jan 1963

5975-00-280-9782
Junction Box

002809782
MT1436-064-400: RNCC: 3 | RNVC: 2

1 Jan 1963

5975-00-281-0089
Junction Box

002810089
W0821ACLASSB2A: RNCC: 4 | RNVC: 1

1 Jan 1963

5975-01-242-5817
Electrical Equipment Rack

012425817
3525075-140: RNCC: 3 | RNVC: 2

13 Oct 1986

5975-01-677-6814
Electric Cable Joint Box Supplementary Equipment

016776814
407392: RNCC: 3 | RNVC: 2

28 Dec 2018

5975-01-677-5464
Electrical-Electronic Equipment Chassis

016775464
CHAS-BP-MX240-S: RNCC: 3 | RNVC: 2
CHAS-BP-MX240-S: RNCC: 5 | RNVC: 2

19 Dec 2018

5975-01-677-6507
Electrical-Electronic Equipment Chassis

016776507
AT-SBX908GEN2: RNCC: 3 | RNVC: 2

27 Dec 2018

5975-01-677-6424
Electronic Junction Rack

016776424
HDO6K-RACK: RNCC: 3 | RNVC: 2
0X00151550: RNCC: 5 | RNVC: 2

26 Dec 2018

5975-01-678-5602
Electrical-Electronic Equipment Chassis

016785602
CHAS-MX80-S: RNCC: 3 | RNVC: 2
CHAS-MX80-S: RNCC: 5 | RNVC: 2

13 Feb 2019

5975-01-678-9397
Electrical Box Connector

016789397
112-1007-0: RNCC: 3 | RNVC: 2

5 Mar 2019

5975-01-678-8741
Electric Cable Joint Box

016788741
112-1028-0: RNCC: 3 | RNVC: 2

1 Mar 2019

5975-01-679-3042
Electrical Equipment Rack

016793042
CS-KIT-WMK=: RNCC: 3 | RNVC: 2

19 Mar 2019

5975-01-679-1419
Electrical-Electronic Equipment Chassis

016791419
MX240BASE-AC-HIGH: RNCC: 3 | RNVC: 2
MX240BASE-AC-HIGH: RNCC: 5 | RNVC: 2

11 Mar 2019

5975-01-592-4376
Blank Panel

015924376
U701F: RNCC: 3 | RNVC: 2
14711-XH: RNCC: C | RNVC: 1

7 Mar 2011

5975-01-414-5137
Flexible Metal Conduit

014145137
1/2FLEXSTEEL: RNCC: 3 | RNVC: 9

8 Jun 1995

5975-01-397-7755
Rigid Metal Conduit

013977755
1310-0101-14: RNCC: 3 | RNVC: 2
1310-0101-14: RNCC: 5 | RNVC: 9

20 Oct 1994

5975-01-219-4886
Conduit Outlet Cover

012194886
FSC-51: RNCC: 3 | RNVC: 9

26 Oct 1985

5975-01-663-8330
Junction Box

016638330
A-1412NF: RNCC: 3 | RNVC: 2
A-1412NF: RNCC: 3 | RNVC: 2
4075889: RNCC: 7 | RNVC: 2

24 May 2017

5975-01-665-4828
Electrical-Electronic Equipment Chassis

016654828
34214687-711R10: RNCC: 3 | RNVC: 2

1 Aug 2017

5975-01-664-8845
Stuffing Tube

016648845
1478768-4: RNCC: 3 | RNVC: 2
1174595: RNCC: 5 | RNVC: 2

11 Jul 2017

5975-01-665-3580
Electrical-Electronic Equipment Panel

016653580
92550-01326-042: RNCC: 3 | RNVC: 2

26 Jul 2017

5975-01-664-5110
Electrical Equipment Mounting Base

016645110
0-1671701-2: RNCC: 3 | RNVC: 9

22 Jun 2017

5975-01-663-6650
Ground Rod Section

016636650
SAGROUNDTARGET-15: RNCC: 3 | RNVC: 9
SAGROUNDTARGET-15: RNCC: 5 | RNVC: 9

17 May 2017

5975-01-576-3230
Junction Box

015763230
95-062-4501-01: RNCC: 3 | RNVC: 2
95-062-4501-01: RNCC: 5 | RNVC: 9

28 Jul 2009

5975-01-576-4048
Electrical Conduit Coupling

015764048
677: RNCC: 3 | RNVC: 2
677: RNCC: 5 | RNVC: 2

30 Jul 2009

5975-01-675-2148
Electrical Components Tie Down Strap

016752148
BT3S-C0: RNCC: 3 | RNVC: 2

28 Aug 2018

5975-01-591-0667
Mounting Plate

015910667
M093041-101: RNCC: 3 | RNVC: 2
M093041-101: RNCC: 3 | RNVC: 9

10 Jan 2011

5975-01-591-0155
Insulator Bracket

015910155
3140045: RNCC: 3 | RNVC: 2

6 Jan 2011

5975-01-592-1173
Electrical-Electronic Equipment Chassis

015921173
TLRC-4: RNCC: 3 | RNVC: 2

22 Feb 2011

5975-01-591-3043
Electrical-Electronic Equipment Chassis

015913043
ECIMLN-MSW5049-11: RNCC: 3 | RNVC: 2

19 Jan 2011

5975-01-408-9254
Electrical-Electronic Equipment Chassis

014089254
A405A075-92: RNCC: 3 | RNVC: 2

1 Mar 1995

5975-01-662-1046
Electrical-Electronic Equipment Panel

016621046
1629-4544: RNCC: 3 | RNVC: 2

27 Mar 2017

5975-01-661-8782
Electrical Equipment Rack Base

016618782
D52760: RNCC: 3 | RNVC: 2
D52760: RNCC: 5 | RNVC: 9

18 Mar 2017

5975-01-661-4041
Electrical Equipment Cabinet

016614041
7517959-904: RNCC: 3 | RNVC: 2

1 Mar 2017

5975-01-661-4212
Interior Cable Rack

016614212
AR8172BLK: RNCC: 3 | RNVC: 2

2 Mar 2017

5975-01-236-2563
Electrical Cable Nipple

012362563
202D242-6: RNCC: 3 | RNVC: 2
202D242-6: RNCC: 5 | RNVC: 2
202D242-6: RNCC: 5 | RNVC: 2

15 Jul 1986

5975-01-574-6215
Electronic Junction Rack

015746215
813R177G03: RNCC: 3 | RNVC: 2

3 Jun 2009

5975-01-575-2722
Electronic Junction Rack

015752722
310-8161: RNCC: 3 | RNVC: 2

25 Jun 2009

5975-01-575-1900
Electronic Equipment Mounting Tray

015751900
MT4-4401: RNCC: 3 | RNVC: 2

23 Jun 2009

5975-01-574-9082
Electrical Conduit Adapter

015749082
750NC102NFA141A141-20-150: RNCC: 3 | RNVC: 2

15 Jun 2009

5975-01-588-2802
Electrical-Electronic Equipment Panel

015882802
549-3612-003: RNCC: 3 | RNVC: 2

10 Sep 2010

5975-01-588-8413
Electrical Equipment Rack

015888413
DE2121-05/30/05: RNCC: 3 | RNVC: 2
9556 004 83101: RNCC: 5 | RNVC: 2

6 Oct 2010

5975-01-589-4730
Electrical Equipment Mounting Base

015894730
M095064-002: RNCC: 3 | RNVC: 2
M095064-002: RNCC: 3 | RNVC: 9

27 Oct 2010

5975-01-589-4521
Electrical-Electronic Equipment Panel

015894521
797-7537-001: RNCC: 3 | RNVC: 2

27 Oct 2010

5975-01-393-0122
Tire Cable

013930122
14000061: RNCC: 3 | RNVC: 2

12 Jul 1994

5975-01-394-5118
Electrical Equipment Mounting Base

013945118
2279-1: RNCC: 3 | RNVC: 2

9 Aug 1994

5975-01-217-2515
Electrical-Electronic Equipment Chassis

012172515
2113373-001: RNCC: 3 | RNVC: 2

23 Sep 1985

5975-01-393-4762
Guide Rail

013934762
174D1869G1: RNCC: 3 | RNVC: 2

20 Jul 1994

5975-01-393-3243
Electrical Equipment Mounting Base

013933243
8010000343-1: RNCC: 3 | RNVC: 9

18 Jul 1994

5975-01-660-0649
Electrical Equipment Rack

016600649
ACX2MR-DHH-SM: RNCC: 3 | RNVC: 2

4 Jan 2017

5975-01-573-6733
Electronic Equipment Mounting Tray

015736733
MT4-4320-102: RNCC: 3 | RNVC: 2
MT4-4320: RNCC: D | RNVC: 9

1 May 2009

5975-01-573-8582
Electrical Equipment Rack

015738582
RX1607-501: RNCC: 3 | RNVC: 2

6 May 2009

5975-01-391-4523
Electrical Equipment Rack

013914523
RA-RSP RACK: RNCC: 3 | RNVC: 9

10 Jun 1994

5975-01-392-5543
Cable Strain Relief Bushing

013925543
380HS013B1912M4: RNCC: 3 | RNVC: 2

1 Jul 1994

5975-01-393-0123
Replenish Pack

013930123
14100624: RNCC: 3 | RNVC: 2

12 Jul 1994

5975-01-393-3245
Electrical Equipment Mounting Base

013933245
8010000345-1: RNCC: 3 | RNVC: 9

18 Jul 1994

5975-01-393-3503
Electrical Nonmetallic Conduit Assembly

013933503
5493230-002: RNCC: 3 | RNVC: 2

18 Jul 1994

5975-01-391-8936
Electrical Conduit Ferrule

013918936
8708-SS-26: RNCC: 3 | RNVC: 2

18 Jun 1994

5975-01-392-1408
Electrical Equipment Mounting Base

013921408
HLN-5189A: RNCC: 3 | RNVC: 9

23 Jun 1994

5975-01-392-4174
Junction Box

013924174
DAA7294D016-005: RNCC: 3 | RNVC: 2

29 Jun 1994

5975-01-160-8238
Conduit Cover Plate

011608238
2896359: RNCC: 3 | RNVC: 2
2896359: RNCC: 5 | RNVC: 2
2896359: RNCC: 5 | RNVC: 9

27 Aug 1983

5975-01-158-3570
Cable Marker Sleeve

011583570
5165369-11: RNCC: 3 | RNVC: 2

21 Jul 1983

5975-01-161-1409
Electrical Cable Protector

011611409
1677: RNCC: 3 | RNVC: 2
3614 PIECE 16: RNCC: 5 | RNVC: 2

1 Sep 1983

5975-01-657-7158
Electrical Cable Protector

016577158
C000100201000: RNCC: 3 | RNVC: 2

26 Aug 2016

5975-01-658-3581
Electrical Fitting Mounting Base

016583581
R00000127021: RNCC: 3 | RNVC: 2

23 Sep 2016

5975-01-657-9281
Electrical Equipment Rack

016579281
23-D1-1018: RNCC: 3 | RNVC: 2

6 Sep 2016

5975-01-280-9582
Electrical Conduit Locknut

012809582
8004059: RNCC: 3 | RNVC: 2

15 Jun 1988

5975-01-281-5460
Cable Collar

012815460
TJ-106-10A: RNCC: 3 | RNVC: 2
84-27009-002: RNCC: 7 | RNVC: 1

25 Jun 1988

5975-01-570-1300
Strain Electrical Conductor Clamp

015701300
BACC10HL2: RNCC: 3 | RNVC: 2

16 Dec 2008

5975-01-569-8203
Electrical Equipment Rack

015698203
X6920A: RNCC: 3 | RNVC: 2
595-6231: RNCC: 5 | RNVC: 2

9 Dec 2008

5975-01-570-8715
Electrical-Electronic Equipment Chassis

015708715
SR2200: RNCC: 3 | RNVC: 2

15 Jan 2009

5975-01-571-5495
Electrical-Electronic Equipment Chassis

015715495
RPC-500NC-00-00: RNCC: 3 | RNVC: 2

9 Feb 2009

5975-01-572-1442
Electronic Junction Rack

015721442
RR1061-10: RNCC: 3 | RNVC: 2

2 Mar 2009

5975-01-571-2720
Electrical Conduit Elbow

015712720
PF7SN: RNCC: 3 | RNVC: 9

29 Jan 2009

5975-01-450-6338
Chassis Base

014506338
26800301: RNCC: 3 | RNVC: 2
9240-004SHEET2: RNCC: 5 | RNVC: 2

17 Nov 1997

5975-01-450-4614
Electrical-Electronic Equipment Panel

014504614
953925-105: RNCC: 3 | RNVC: 2

10 Nov 1997

5975-01-656-4764
Electrical Equipment Rack

016564764
RA 19-4C: RNCC: 3 | RNVC: 2

5 Jul 2016

5975-01-025-1870
Tape Guide Plate

010251870
85-18372-0050: RNCC: 3 | RNVC: 2

28 Jul 1976

5975-01-569-4333
Cord Assembly Fastener

015694333
M8532: RNCC: 3 | RNVC: 2

2 Dec 2008

5975-01-569-8947
Electrical Equipment Mounting Base

015698947
204-57433-6: RNCC: 3 | RNVC: 2

10 Dec 2008

5975-01-570-2502
Electrical-Electronic Equipment Chassis

015702502
14711-4: RNCC: 3 | RNVC: 2
310-9711: RNCC: 5 | RNVC: 2
JP867: RNCC: 5 | RNVC: 2

18 Dec 2008

5975-01-569-4950
Electrical Bushing

015694950
RW309-18: RNCC: 3 | RNVC: 2

3 Dec 2008

5975-01-569-7095
Blank Panel

015697095
14711-9: RNCC: 3 | RNVC: 2
310-9709: RNCC: 5 | RNVC: 2
XW300: RNCC: 5 | RNVC: 2
XW300: RNCC: 5 | RNVC: 2

8 Dec 2008

5975-01-451-9988
Junction Box Cover

014519988
3351133-3: RNCC: 3 | RNVC: 2

12 Jan 1998

5975-01-451-9994
Cable Marker Sleeve

014519994
013-007382-038: RNCC: 3 | RNVC: 2

12 Jan 1998

5975-01-451-9456
Cable Marker Sleeve

014519456
013-007382-013: RNCC: 3 | RNVC: 2

9 Jan 1998

5975-01-354-2034
Electrical Components Tie Down Strap

013542034
5497468-1: RNCC: 3 | RNVC: 2
2927-2-3: RNCC: C | RNVC: 1

25 Feb 1992

5975-01-390-2213
Electrical-Electronic Equipment Chassis

013902213
1103-102: RNCC: 3 | RNVC: 2
62828-90109-17: RNCC: 5 | RNVC: 2

13 May 1994

5975-01-024-0677
Front Cover

010240677
50-18372-0010: RNCC: 3 | RNVC: 2

4 Jul 1976

5975-01-024-0678
Sleeve

010240678
57-30481-0010: RNCC: 3 | RNVC: 2

4 Jul 1976

5975-01-234-6646
Wiring Duct

012346646
LD3LG6-A: RNCC: 3 | RNVC: 2

18 Jun 1986

5975-01-103-9646
Junction Box

011039646
374303-2: RNCC: 3 | RNVC: 2

23 Nov 1980

5975-01-105-4248
Ground Strap

011054248
3150100-601-5: RNCC: 3 | RNVC: 2

23 Dec 1980

5975-01-105-4245
Ground Strap

011054245
3150100-601-27: RNCC: 3 | RNVC: 2

23 Dec 1980

Load More Results