What is Federal Supply Class 5975?

FSC 5975 is the Federal Supply Class (formally known as NATO Supply Classification Class NSC 5975) in the USA for supply items codified in the category of Electrical Hardware and Supplies.

What is NATO Supply Classification Class 5975?

NSC 5975 is the NATO Supply Classification Class (also known as Federal Supply Class FSC 5975 in the USA) for supply items codified in the category of Electrical Hardware and Supplies.

Which Federal Supply Group is FSC 5975 in?

FSC 5975 is in Federal Supply Group (FSG) 59 which contains Electrical and Electronic Equipment Components.

Which NATO Supply Classification Group is NSC 5975 in?

NSC 5975is in NATO Supply Classification Group (NSG) 59 which contains Electrical and Electronic Equipment Components.

What is an Electrical Cable Protector?

An Electrical Cable Protector (PROTECTOR,ELECTRICAL CABLE) is an item designed to be interposed between a cable and its support or housing to prevent chafing caused by contraction and expansion due to changes in the ambient temperature or damage or injury from outside sources. Excludes such items as loom, cotton sleeving, rubber blankets, grade clamps and all types of conduit and INSULATION SLEEVING, ELECTRICAL.

What is a Ground Rod?

A Ground Rod (ROD,GROUND) is an item designed to be driven into the earth for the purpose of establishing electrical contact. One end is pointed or tapered to facilitate entrance into the earth. See also ROD SECTION, GROUND.

What is a Junction Box Assembly?

A Junction Box Assembly is two or more junction boxes on a common mounting or mounted on each other. Do not use for single junction boxes which are complex or unusual in construction, or for a junction box with an extension. See also TERMINAL BOX.

What is a Flexible Metal Conduit Assembly?

A Flexible Metal Conduit Assembly (CONDUIT ASSEMBLY,METAL,FLEXIBLE) is a specific length of CONDUIT, METAL, FLEXIBLE with permanently attached ferrule(s), coupling nut(s), elbow(s), or the like. Excludes detachable fittings such as tee(s), wye(s), or elbow(s). Also, excludes conduit like items that are designed for other than electrical applications. See also CASING (as modified).

What is a Fanning Strip?

A Fanning Strip is an item made of rigid or semirigid insulating material for spacing or separating wire(s) and/or cable(s). For items having terminals, see TERMINAL BOARD; and INSULATOR (as modified).

A Pothead is a form of terminator, usually used in power and telephone distribution, designed to be hermetically sealed to the cable(s) to exclude moisture. It may have terminals accessible for testing, or a junction block to facilitate the connecting of cable(s) and wire. See also SEALING FITTING, ELECTRICAL CONDUIT.

What is a Switch Terminal Cover?

A Switch Terminal Cover (COVER,SWITCH TERMINAL) is an item generally made of insulating material and used to protect switch terminals against damage, shorting and grounding. Excludes COVER, ELECTRICAL SWITCH; BASE, SWITCH and HOUSING, SENSITIVE SWITCH.

What is a Cable Terminal Chamber?

A Cable Terminal Chamber (CHAMBER,CABLE TERMINAL) is an item specifically designed to admit, protect and seal conductor groups or cables and also affords a method of conveniently distributing, terminating and interconnecting the leads.

What is a Stuffing Tube?

A Stuffing Tube is an item specifically designed to pass an electrical cable or tube through a continuous structure with provisions for packing so as to prevent the leakage of liquids and/or gases through the opening. May include packing nut(s), adapter(s), washer(s), gasket(s), bushing(s), packing(s), cap(s), and/or plug(s).

What is a Cord Assembly Fastener?

A Cord Assembly Fastener (FASTENER,CORD ASSEMBLY) is a fastener primarily designed to hold and secure a cord assembly so that pulling of the cord will not put a strain on the terminal connections.

What is an Electrical Grounding Plate?

An Electrical Grounding Plate (PLATE,ELECTRICAL GROUNDING) is a rigid or semirigid item of electrically conductive material whose thickness is small in comparsion to its length and width. It is designed to be used for electrical grounding, particularly in junction box and power outlet applications. Excludes TERMINAL STRIP, GROUNDING; CONTACT STRIP, RADIO FREQUENCY GROUNDING; and STRIP, ELECTRICAL GROUNDING.

What is a Cable Collar?

A Cable Collar (COLLAR,CABLE) is an item designed to be affixed around an electrical cable to limit the axial movement of the cable at the point where it passes through an opening. It has no facilities for retaining the cable to another object. Excludes BUSHING, STRAIN RELEIF, CABLE.

What is a Crossarm Brace?

A Crossarm Brace (BRACE,CROSSARM) is an item specifically designed to provide reinforcement for a crossarm when mounted on a pole.

What is a Cable Hanger?

A Cable Hanger (HANGER,CABLE) is a metallic or nonmetallic item of various shapes, designed to position, suspend, support and/or secure electrical cable(s) to utility poles, bulkheads, messenger wires or other supporting surfaces. It may be fastened to the structure by means of rod(s), bolts(s), screw(s) and the like. Excludes CLAMP (as modified); HANGER, WIRE STRAND; BRACKET PIPE; and SUPPORT, ELECTRICAL CABLE.

What is an Insulator Pin?

An Insulator Pin (PIN,INSULATOR) is an item designed to be inserted into a crossarm for the specific purpose of mounting pin type electrical insulators. Excludes BRACKET, INSULATOR.

What is a Stuffing Tube Plug?

A Stuffing Tube Plug (PLUG,STUFFING TUBE) is an item designed to be fitted into the body of a STUFFING TUBE in order to prevent the leakage of liquids and/or gases through the opening in the absence of the cable normally passing through the tube.

What is an Electrical Cable Support?

An Electrical Cable Support (SUPPORT,ELECTRICAL CABLE) is a collapsible framework specifically designed to be placed on the ground to hold electrical cable above the ground surface. Excludes BRACKET, PIPE.

What is an Electrical Conductor Bushing?

An Electrical Conductor Bushing (BUSHING,ELECTRICAL CONDUCTOR) is an item of metal and/or insulating material having a smooth interior with rounded edges to prevent damage to the insulation of the wire or cable emerging there-from, designed to fit through panel(s) or the wall of a JUNCTION BOX. It may be designed to snap into a knockout hole, or designed with an external thread and furnished with or without a locking nut. For items designed to couple conduit to JUNCTION BOX, see BOX CONNECTOR, ELECTRICAL. See also BUSHING, ELECTRICAL CONDUIT and BUSHING, NONMETALLIC. For items having hexagonal shoulders, see CHASE NIPPLE, CONDUIT.

What is an Insulator Bracket?

An Insulator Bracket (BRACKET,INSULATOR) is an item designed to be attached to a supporting surface for the specific purpose of positioning and sustaining an electrical insulator(s). Includes brackets specifically designed for transposing electrical lines.

What is a Cable Reinforcing Link?

A Cable Reinforcing Link (LINK,REINFORCING,CABLE) is an item fabricated from metal rod bent longitudinally into an oval shape, one end of which is intended to fit a messenger cable or guy wire and the opposite end formed with a mounting hole for a lag screw. This item is designed to relieve the strain where a messenger cable or wire is installed at an angle to a suspension clamp.

What is a Stuffing Tube Adapter?

A Stuffing Tube Adapter (ADAPTER,STUFFING TUBE) is a threaded or unthreaded item designed to mate with the mounting threads or mounting surfaces of a STUFFING TUBE, and to mount the STUFFING TUBE to a continuous structure (bulkhead or deck). The adapter may be recessed on the face to accommodate a gasket and/or washer.

What is a Junction Box?

A Junction Box is an enclosure of other than cast metal designed to house, mount, and protect, but does not include wiring connections or electrical device(s) such as terminals and/or terminal boards, switches, jacks, fuseholders, connectors, circuit breakers and the like. It is designed for and may include a cover and such accessories as mounting hardware, brackets, locks, clamps, mounts and conduit fittings. Excludes CONDUIT OUTLET; and CHAMBER, CABLE TERMINAL. For boxes which include electrical device(s) such as terminals and/or terminal boards, switches, fuseholders, jacks, connectors, circuit breakers and the like, or combinations thereof, see SWITCH BOX; FUZE BOX; JACK BOX; TERMINAL BOX; CIRCUIT BREAKER BOX; and DISTRIBUTION BOX. For boxes wired to provide the interconnecting facilities for a specific major group of electronic items outside of the box, see INTERCONNECTING BOX. See also INTERCONNECTING CABINET.

What is an Electrical Cable Nipple?

An Electrical Cable Nipple (CABLE NIPPLE,ELECTRICAL) is a preformed item having high electrical resistance designed for installation on end of cable or lead in order to cover the terminal or termination. It may partially cover the terminal of the item to which the cable or lead is attached. May also provide mechanical protection. Excludes INSULATION SLEEVING, ELECTRICAL.

What is an Electrical Equipment Cabinet?

An Electrical Equipment Cabinet (CABINET,ELECTRICAL EQUIPMENT) is an enclosure generally fabricated of sheet material designed to accommodate (but does not include) electrical/electronic equipment so that the equipment may be operated without removal. It may include wires, cables, terminal boards, connectors, etc., required for equipment operation. For items designed to accommodate equipment mounted on panels, see RACK, ELECTRICAL EQUIPMENT. See also CASE (2) (as modified). Excludes INTERCONNECTING BOX; INTERCONNECTING CABINET; JUNCTION BOX; and TERMINAL BOX.

What is an Electrical Equipment Rack?

An Electrical Equipment Rack (RACK,ELECTRICAL EQUIPMENT) is an open or inclosed frame structure designed to accommodate (but does not include) electrical/electronic equipment mounted on standard width panels so that the equipment may be operated after installation without being removed. It must have panel mounting rails that provide a uniform pattern of mounting holes that will accommodate various combinations of standard width panels. It may include wires, cables, terminal boards, connectors, and the like, required for equipment operation. See also MOUNTING BASE, ELECTRICAL EQUIPMENT; CABINET, ELECTRICAL EQUIPMENT; and CASE (2) (as modified). Excludes MAIN DISTRIBUTING FRAME, TELEPHONE and INTERMEDIATE DISTRIBUTING FRAME, TELEPHONE.

What is an Electrical Entrance Cap?

An Electrical Entrance Cap (ENTRANCE CAP,ELECTRICAL) is an item primarily designed to provide for the entrance of electrical wires into a building, structure, or inclosure and to facilitate their connection to feeders or service conductors. It consists of an insulating block and a metallic housing designed to hold the insulating block and to fit an electrical conduit, conduit fitting, or cable of a specified size. This item is primarily intended for use in exposed, wet, or damp locations and is installed so as to preclude the entrance of rain or debris into the conduit. See also CAP, ELECTRICAL.

What is an Electrical Conduit Adapter?

An Electrical Conduit Adapter (ADAPTER,ELECTRICAL CONDUIT) is an item designed to couple or join two different types or sizes of conduits, and/or to be inserted in the opening of a conduit outlet or box to accommodate a conduit of a larger or smaller size; or it may be designed with internal thread on one end for mating with an electrical connector and an external thread on the other end for mating with a conduit coupling nut; or to establish necessary mechanical accommodations between an electrical conduit, conduit assembly and an electrical connector. Excludes REDUCING WASHER, KNOCKOUT and BOX CONNECTOR, ELECTRICAL. See also ADAPTER, CABLE TO CONNECTOR; and CHASE NIPPLE, CONDUIT.

What is an Electrical Conduit Sealing Fitting?

An Electrical Conduit Sealing Fitting (SEALING FITTING,ELECTRICAL CONDUIT) is an item of metallic composition with a chamber for sealing compound and two hubs to accommodate electrical conduits of specified sizes. This item is designed with a filler hole and a removable screw plug to enable the pouring of sealing compound into the chamber for the purpose of preventing the passage of explosive gases through a conduit run. The item is primarily designed for use in hazardous locations and may be designed for vertical use, horizontal use, or both. For items which permit the connection or termination of wires, see POTHEAD. See also COUPLING, ELECTRICAL CONDUIT.

What is a Knockout Reducing Washer?

A Knockout Reducing Washer (REDUCING WASHER,KNOCKOUT) is an item consisting of a flat, cupped or embossed metallic disk with a centerhole to fit an electrical conduit of a specified size and which is specifically designed to reduce the knockout opening in a box, panel, or wireway for the convenience of terminating electrical conduit of smaller size than the knockout. Excludes ADAPTER, ELECTRICAL CONDUIT.

What is an Electrical Conduit Nipple?

An Electrical Conduit Nipple (NIPPLE,ELECTRICAL CONDUIT) is a nipple made of electrical conduit.

What is an Electrical Entrance Elbow?

An Electrical Entrance Elbow (ENTRANCE ELBOW,ELECTRICAL) is an item of metallic composition cast in the form of an elbow, which is primarily intended to provide for the angular entrance of wires into a building, structure, or enclosure. This item, specifically designed for installation in exposed locations, has two hubs of a specified size to fit the service entrance conduit and may have a third hub for a driven ground connection. It has a cover which makes it tamper-proof and weather-resistant. It may include facilities for pulling electrical conductors but does not have facilities for mounting wiring devices.

What is an Electrical Conduit Bushing?

An Electrical Conduit Bushing (BUSHING,ELECTRICAL CONDUIT) is an item of metal and/or insulating material having internal threads designed to fit over the end of electrical conduit and/or fittings to provide a smooth interior with a rounded edge to prevent damage to the insulation of the wire or cable emerging therefrom. It may be designed to fit over the end of thin wall conduit, and to be fitted with holding (staking) screws, or it may be provided with internal straight threads for attaching to thick wall electrical conduit or fittings. It may be fitted with a temporary knockout cap (bushcap), and grounding or bonding facilities. For externally threaded items, see BOX CONNECTOR, ELECTRICAL; BUSHING, ELECTRICAL CONDUCTOR; CHASE NIPPLE, CONDUIT and BUSHING, STRAIN RELIEF, CABLE. See also FERRULE, ELECTRICAL CONDUIT. Excludes plain sleeve bushings.

What is an Electrical Conduit Bondnut?

An Electrical Conduit Bondnut (BONDNUT,ELECTRICAL CONDUIT) is an item of metallic composition, with internal threads, designed to fit the external threads of an electrical conduit or fitting, and which, when installed, provides a method of tightening and locking the connection and completes a positive bond between the conduit and apparatus or fitting to which connected. The bonding or grounding action is accomplished by sharp beveled teeth or by a screw(s). See also LOCKNUT, ELECTRICAL CONDUIT and NUT, COUPLING, ELECTRICAL CONDUIT.

What is an Electrical Conduit Union?

An Electrical Conduit Union (UNION,ELECTRICAL CONDUIT) is an item comprising three members, so constructed that one of the members holds the remaining two in a fixed butted position; generally used to connect two conduits, conduit fittings, or a conduit and a conduit fitting in such a manner that they may be disconnected without disturbing the rest of the conduit line. See also COUPLING, ELECTRICAL CONDUIT.

What is an Electrical Conduit Elbow?

An Electrical Conduit Elbow (ELBOW,ELECTRICAL CONDUIT) is an item fabricated in the form of an elbow and having both ends threaded female, or with unthreaded connecting facilities on both ends, or connecting facilities on both ends, one of which is a male thread without boss or shoulder. If a locknut or bondnut is included, it shall not be considered as a thread boss or shoulder. It is primarily intended to connect conduit to conduit. It may have a removable cover to facilitate pulling wires, but does not include facilities for mounting wiring devices. For items having a removable cover to facilitate pulling wires and specifically designed for close installation in exposed outdoor locations and which may have facilities for an outside driven ground, see ENTRANCE ELBOW, ELECTRICAL. For items with one end having a male thread with a boss or shoulder, see BOX CONNECTOR, ELECTRICAL. For items having a removable screw cap for pulling wires, with the cap positioned 45 degrees from the connection facilities, see ENTRANCE ELBOW, ELECTRICAL. For items fabricated in the form of an elbow having both ends threaded male, see BEND, ELECTRICAL CONDUIT.

What is a Conduit Outlet?

A Conduit Outlet is an item designed to be used in a conduit system for the purpose of providing outlets or attachments for electrical wiring devices and/or designed to provide access and facilitate installment of wires. It may or may not include a cover(s). It does not include wiring devices. Excludes ENTRANCE ELBOW, ELECTRICAL. See also JUNCTION BOX.

What is an Electrical Conduit Bend?

An Electrical Conduit Bend (BEND,ELECTRICAL CONDUIT) is an item fabricated in the form of a curved section specifically designed to mechanically join a conduit or conduit fitting to another conduit or conduit fitting. Items of this type do not have a boss or hub at either end, nor do they have facilities for mounting wiring devices or pulling electrical conductors. See also ELBOW, ELECTRICAL CONDUIT and CONDUIT OUTLET.

What is an Electrical Wall Plate?

An Electrical Wall Plate (PLATE,WALL,ELECTRICAL) is an item designed to mount directly on a bracket or an electrical current carrying wiring device(s) such as switch(es) or outlet(s) (receptacle). The bracket(s) or electrical current carrying device is mounted in a JUNCTION BOX. For trade designated items designed to be attached directly on or through a bracket or electrical wiring device to a CONDUIT OUTLET, see COVER, CONDUIT OUTLET. For items designed for mounting directly on a JUNCTION BOX, see COVER, JUNCTION BOX.

What is an Interconnecting Box?

An Interconnecting Box is an inclosure which includes mounts and protects such items as switches, circuit breakers, jacks, fuseholders, connectors, terminals and/or terminal boards, resistors, capacitors, transformers, and the like. It is primarily designed to interconnect two or more electrical and/or electronic items, except primary power source(s) such as generator(s) and battery(ies). It may include a cover or door. For inclosures which connect one or more primary power source(s) to one or more electrical and/or electronic item(s), see DISTRIBUTION BOX. See also CIRCUIT BREAKER BOX; TERMINAL BOX and INTERCONNECTING CABINET.

A Pole Step (STEP,POLE) is an item designed to be used as a foot rest in ascending and descending utility poles, when attached thereto.

What is an Interior Cable Rack?

An Interior Cable Rack (RACK,CABLE,INTERIOR) is an open frame structure primarily designed to support electrical cables in buildings and shelters. Its purpose is to provide, by itself or by joining to similar structures, a path or runway for cable which may connect two or more pieces of electrical equipment. It does not include items designed to hold a single cable. See also RACK, CABLE, UNDERGROUND; and HANGER, CABLE.

What is an Electrical Conduit Ferrule?

An Electrical Conduit Ferrule (FERRULE,ELECTRICAL CONDUIT) is an item usually of one piece construction, but which may be comprised of more than one piece, designed to be affixed permanently or temporarily to the end of an electrical conduit to form an end fitting. Unflanged items form a permanent end fitting which affords mechanical protection to emerging conductors. Flanged items are used with another fitting normally a conduit coupling nut, to make the conduit adaptable for connection to an electrical connector, junction box or other conduit accessory or fitting. Excludes RING, ELECTRICAL BONDING; BUSHING, ELECTRICAL CONDUIT; and BUSHING, PLAIN SLEEVE. See also FERRULE-NUT COUPLING, ELECTRICAL CONDUIT.

What is an Underground Cable Rack Hook?

An Underground Cable Rack Hook (HOOK,UNDERGROUND CABLE RACK) is a rigid item designed to be perpendicularly attached to an underground cable rack to be used as the supporting arm for cables. May include insulators.

What is an Electrical Conduit End Seal Disk?

An Electrical Conduit End Seal Disk (DISK,END SEAL,ELECTRICAL CONDUIT) is a flat circular item fitted on the end of an electrical conduit in order to close the end to prevent the entrance of water or refuse, prior to installation of the wires, during shipment and/or construction. The item may be held in place by means of a conduit bushing and may be easily removed to permit installation of the wires.

What is a Cable Spacer?

A Cable Spacer (SPACER,CABLE) is an item constructed specifically to provide a separation between lashed lead covered cable and messenger strand for the prevention of injury to sheath of cable.

What is an Electrical Box Connector?

An Electrical Box Connector (BOX CONNECTOR,ELECTRICAL) is an item designed to mechanically connect in a straight line or an angle electrical conduit, conduit assemblies, wire, wireway, cable, or cable assemblies to a point of termination, such as a junction box, conduit outlet, or the like. The termination end must have an external thread with a boss or shoulder and may be furnished with a locknut or bondnut; or, must have internal thread with which is furnished an externally threaded hub with a wrenching feature; or be of a snap-in type that may be installed from either inside or outside the box and secured with a captive screw. It is not intended to join conduit to conduit. For angle type items having a male thread without a boss or shoulder, see ELBOW, ELECTRICAL CONDUIT. Does not include facilities to mount wiring devices. Excludes CHASE NIPPLE, CONDUIT.

What is an Electrical Conduit Coupling?

An Electrical Conduit Coupling (COUPLING,ELECTRICAL CONDUIT) is an item specifically designed and constructed to mechanically connect in a straight line two sections of electrical conduit or like fabrication and of the same size. For three-piece items which may be disassembled without disturbing the rest of the conduit line, see UNION, ELECTRICAL CONDUIT. See also ADAPTER, ELECTRICAL CONDUIT; POTHEAD; and SEALING FITTING, ELECTRICAL CONDUIT.

Electrical Hardware and Supplies - United States (US)

Federal Supply Class (FSC): 5975

NATO Supply Classification Class (NSC): 5975

Federal Supply Group (FSG): 59 Electrical and Electronic Equipment Components

NATO Supply Classification Group (NSG): 59 Electrical and Electronic Equipment Components

Items Managed by United States (US) - NCB is 00 to 09

Page 168 of 176

NSN Format for Electrical Hardware and Supplies
Codified by United States

59	75	01	XXX
Group FSG	Class	NCB	Identifier
FSC Federal Supply Class		NIIN
NSN

NATO Supply Class 5975 is a classification within NATO Supply Group 59, which is dedicated to Electrical and Electronic Equipment Components.

NATO Supply Class 5975 specifically focuses on Electrical Hardware and Supplies. This class includes a wide range of items such as electrical connectors, terminals, switches, circuit breakers, fuses, relays, cables, wires, and other related electrical components and accessories.

The purpose of this classification is to provide a standardized system for categorizing and organizing electrical hardware and supplies used in military and defense applications. By using this classification system, NATO member countries can easily identify, procure, and maintain the necessary electrical components for their equipment and systems.

It is important to note that the NATO Supply Classification (NSC) system is used primarily by NATO member countries for logistical and supply chain management purposes. It helps ensure interoperability and compatibility among different military forces by providing a common language for identifying and categorizing various items.

If you are working on a document related to electrical hardware and supplies in the context of NATO Supply Class 5975, you may want to include specific details about the types of components and their applications within military and defense systems. Additionally, you can mention the importance of adhering to the NATO Supply Classification system for efficient procurement and maintenance processes.

FSC 5975 Electrical Hardware and Supplies - United States (US)

Includes Conduit; Raceways; Face Plates; Condulets; Outlet and Junction Boxes; Pole Line Hardware, not elsewhere classifiable.

Note-Mounting hardware, included in classes of this group, includes such specially designed items as brackets, holders, retainers, etc. Excluded from classes in this group are such hardware items as screws (Class 5305), bolts (Class 5306), studs (Class 5307), washers (Class 5310), rivets (Class 5320), and other common items indexed to specific classes, other than in Group 59. The FSC indexes and structure will govern the classification of items used on or with mounting hardware cited above.

Frequently Asked Questions(FAQ) for Federal Supply Class 5975

What is Federal Supply Class 5975?: FSC 5975 is the Federal Supply Class (formally known as NATO Supply Classification Class NSC 5975) in the USA for supply items codified in the category of Electrical Hardware and Supplies.
What is NATO Supply Classification Class 5975?: NSC 5975 is the NATO Supply Classification Class (also known as Federal Supply Class FSC 5975 in the USA) for supply items codified in the category of Electrical Hardware and Supplies.
Which Federal Supply Group is FSC 5975 in?: FSC 5975 is in Federal Supply Group (FSG) 59 which contains Electrical and Electronic Equipment Components.
Which NATO Supply Classification Group is NSC 5975 in?: NSC 5975 is in NATO Supply Classification Group (NSG) 59 which contains Electrical and Electronic Equipment Components.

Supply Items Included in Federal Supply Class 5975

What is an Electrical Cable Protector? 768 Items: An Electrical Cable Protector (PROTECTOR,ELECTRICAL CABLE) is an item designed to be interposed between a cable and its support or housing to prevent chafing caused by contraction and expansion due to changes in the ambient temperature or damage or injury from outside sources. Excludes such items as loom, cotton sleeving, rubber blankets, grade clamps and all types of conduit and INSULATION SLEEVING, ELECTRICAL.
What is a Ground Rod? 262 Items: A Ground Rod (ROD,GROUND) is an item designed to be driven into the earth for the purpose of establishing electrical contact. One end is pointed or tapered to facilitate entrance into the earth. See also ROD SECTION, GROUND.
What is a Junction Box Assembly? 258 Items: A Junction Box Assembly is two or more junction boxes on a common mounting or mounted on each other. Do not use for single junction boxes which are complex or unusual in construction, or for a junction box with an extension. See also TERMINAL BOX.
What is a Flexible Metal Conduit Assembly? 1671 Items: A Flexible Metal Conduit Assembly (CONDUIT ASSEMBLY,METAL,FLEXIBLE) is a specific length of CONDUIT, METAL, FLEXIBLE with permanently attached ferrule(s), coupling nut(s), elbow(s), or the like. Excludes detachable fittings such as tee(s), wye(s), or elbow(s). Also, excludes conduit like items that are designed for other than electrical applications. See also CASING (as modified).
What is a Fanning Strip? 139 Items: A Fanning Strip is an item made of rigid or semirigid insulating material for spacing or separating wire(s) and/or cable(s). For items having terminals, see TERMINAL BOARD; and INSULATOR (as modified).
What is a Pothead? 13 Items: A Pothead is a form of terminator, usually used in power and telephone distribution, designed to be hermetically sealed to the cable(s) to exclude moisture. It may have terminals accessible for testing, or a junction block to facilitate the connecting of cable(s) and wire. See also SEALING FITTING, ELECTRICAL CONDUIT.
Cover,Interconnecting Box 59 Items
What is a Switch Terminal Cover? 107 Items: A Switch Terminal Cover (COVER,SWITCH TERMINAL) is an item generally made of insulating material and used to protect switch terminals against damage, shorting and grounding. Excludes COVER, ELECTRICAL SWITCH; BASE, SWITCH and HOUSING, SENSITIVE SWITCH.
What is a Cable Terminal Chamber? 141 Items: A Cable Terminal Chamber (CHAMBER,CABLE TERMINAL) is an item specifically designed to admit, protect and seal conductor groups or cables and also affords a method of conveniently distributing, terminating and interconnecting the leads.
What is a Stuffing Tube? 1137 Items: A Stuffing Tube is an item specifically designed to pass an electrical cable or tube through a continuous structure with provisions for packing so as to prevent the leakage of liquids and/or gases through the opening. May include packing nut(s), adapter(s), washer(s), gasket(s), bushing(s), packing(s), cap(s), and/or plug(s).
What is a Cord Assembly Fastener? 28 Items: A Cord Assembly Fastener (FASTENER,CORD ASSEMBLY) is a fastener primarily designed to hold and secure a cord assembly so that pulling of the cord will not put a strain on the terminal connections.
What is an Electrical Grounding Plate? 501 Items: An Electrical Grounding Plate (PLATE,ELECTRICAL GROUNDING) is a rigid or semirigid item of electrically conductive material whose thickness is small in comparsion to its length and width. It is designed to be used for electrical grounding, particularly in junction box and power outlet applications. Excludes TERMINAL STRIP, GROUNDING; CONTACT STRIP, RADIO FREQUENCY GROUNDING; and STRIP, ELECTRICAL GROUNDING.
What is a Cable Collar? 124 Items: A Cable Collar (COLLAR,CABLE) is an item designed to be affixed around an electrical cable to limit the axial movement of the cable at the point where it passes through an opening. It has no facilities for retaining the cable to another object. Excludes BUSHING, STRAIN RELEIF, CABLE.
Base,Chassis 324 Items
What is a Crossarm Brace? 31 Items: A Crossarm Brace (BRACE,CROSSARM) is an item specifically designed to provide reinforcement for a crossarm when mounted on a pole.
What is a Cable Hanger? 814 Items: A Cable Hanger (HANGER,CABLE) is a metallic or nonmetallic item of various shapes, designed to position, suspend, support and/or secure electrical cable(s) to utility poles, bulkheads, messenger wires or other supporting surfaces. It may be fastened to the structure by means of rod(s), bolts(s), screw(s) and the like. Excludes CLAMP (as modified); HANGER, WIRE STRAND; BRACKET PIPE; and SUPPORT, ELECTRICAL CABLE.
What is an Insulator Pin? 55 Items: An Insulator Pin (PIN,INSULATOR) is an item designed to be inserted into a crossarm for the specific purpose of mounting pin type electrical insulators. Excludes BRACKET, INSULATOR.
What is a Stuffing Tube Plug? 53 Items: A Stuffing Tube Plug (PLUG,STUFFING TUBE) is an item designed to be fitted into the body of a STUFFING TUBE in order to prevent the leakage of liquids and/or gases through the opening in the absence of the cable normally passing through the tube.
What is an Electrical Cable Support? 74 Items: An Electrical Cable Support (SUPPORT,ELECTRICAL CABLE) is a collapsible framework specifically designed to be placed on the ground to hold electrical cable above the ground surface. Excludes BRACKET, PIPE.
What is an Electrical Conductor Bushing? 421 Items: An Electrical Conductor Bushing (BUSHING,ELECTRICAL CONDUCTOR) is an item of metal and/or insulating material having a smooth interior with rounded edges to prevent damage to the insulation of the wire or cable emerging there-from, designed to fit through panel(s) or the wall of a JUNCTION BOX. It may be designed to snap into a knockout hole, or designed with an external thread and furnished with or without a locking nut. For items designed to couple conduit to JUNCTION BOX, see BOX CONNECTOR, ELECTRICAL. See also BUSHING, ELECTRICAL CONDUIT and BUSHING, NONMETALLIC. For items having hexagonal shoulders, see CHASE NIPPLE, CONDUIT.
What is an Insulator Bracket? 144 Items: An Insulator Bracket (BRACKET,INSULATOR) is an item designed to be attached to a supporting surface for the specific purpose of positioning and sustaining an electrical insulator(s). Includes brackets specifically designed for transposing electrical lines.
What is a Cable Reinforcing Link? 21 Items: A Cable Reinforcing Link (LINK,REINFORCING,CABLE) is an item fabricated from metal rod bent longitudinally into an oval shape, one end of which is intended to fit a messenger cable or guy wire and the opposite end formed with a mounting hole for a lag screw. This item is designed to relieve the strain where a messenger cable or wire is installed at an angle to a suspension clamp.
What is a Stuffing Tube Adapter? 72 Items: A Stuffing Tube Adapter (ADAPTER,STUFFING TUBE) is a threaded or unthreaded item designed to mate with the mounting threads or mounting surfaces of a STUFFING TUBE, and to mount the STUFFING TUBE to a continuous structure (bulkhead or deck). The adapter may be recessed on the face to accommodate a gasket and/or washer.
What is a Junction Box? 2471 Items: A Junction Box is an enclosure of other than cast metal designed to house, mount, and protect, but does not include wiring connections or electrical device(s) such as terminals and/or terminal boards, switches, jacks, fuseholders, connectors, circuit breakers and the like. It is designed for and may include a cover and such accessories as mounting hardware, brackets, locks, clamps, mounts and conduit fittings. Excludes CONDUIT OUTLET; and CHAMBER, CABLE TERMINAL. For boxes which include electrical device(s) such as terminals and/or terminal boards, switches, fuseholders, jacks, connectors, circuit breakers and the like, or combinations thereof, see SWITCH BOX; FUZE BOX; JACK BOX; TERMINAL BOX; CIRCUIT BREAKER BOX; and DISTRIBUTION BOX. For boxes wired to provide the interconnecting facilities for a specific major group of electronic items outside of the box, see INTERCONNECTING BOX. See also INTERCONNECTING CABINET.
What is an Electrical Cable Nipple? 547 Items: An Electrical Cable Nipple (CABLE NIPPLE,ELECTRICAL) is a preformed item having high electrical resistance designed for installation on end of cable or lead in order to cover the terminal or termination. It may partially cover the terminal of the item to which the cable or lead is attached. May also provide mechanical protection. Excludes INSULATION SLEEVING, ELECTRICAL.
What is an Electrical Equipment Cabinet? 1478 Items: An Electrical Equipment Cabinet (CABINET,ELECTRICAL EQUIPMENT) is an enclosure generally fabricated of sheet material designed to accommodate (but does not include) electrical/electronic equipment so that the equipment may be operated without removal. It may include wires, cables, terminal boards, connectors, etc., required for equipment operation. For items designed to accommodate equipment mounted on panels, see RACK, ELECTRICAL EQUIPMENT. See also CASE (2) (as modified). Excludes INTERCONNECTING BOX; INTERCONNECTING CABINET; JUNCTION BOX; and TERMINAL BOX.
What is an Electrical Equipment Rack? 2666 Items: An Electrical Equipment Rack (RACK,ELECTRICAL EQUIPMENT) is an open or inclosed frame structure designed to accommodate (but does not include) electrical/electronic equipment mounted on standard width panels so that the equipment may be operated after installation without being removed. It must have panel mounting rails that provide a uniform pattern of mounting holes that will accommodate various combinations of standard width panels. It may include wires, cables, terminal boards, connectors, and the like, required for equipment operation. See also MOUNTING BASE, ELECTRICAL EQUIPMENT; CABINET, ELECTRICAL EQUIPMENT; and CASE (2) (as modified). Excludes MAIN DISTRIBUTING FRAME, TELEPHONE and INTERMEDIATE DISTRIBUTING FRAME, TELEPHONE.
What is an Electrical Entrance Cap? 43 Items: An Electrical Entrance Cap (ENTRANCE CAP,ELECTRICAL) is an item primarily designed to provide for the entrance of electrical wires into a building, structure, or inclosure and to facilitate their connection to feeders or service conductors. It consists of an insulating block and a metallic housing designed to hold the insulating block and to fit an electrical conduit, conduit fitting, or cable of a specified size. This item is primarily intended for use in exposed, wet, or damp locations and is installed so as to preclude the entrance of rain or debris into the conduit. See also CAP, ELECTRICAL.
What is an Electrical Conduit Adapter? 1842 Items: An Electrical Conduit Adapter (ADAPTER,ELECTRICAL CONDUIT) is an item designed to couple or join two different types or sizes of conduits, and/or to be inserted in the opening of a conduit outlet or box to accommodate a conduit of a larger or smaller size; or it may be designed with internal thread on one end for mating with an electrical connector and an external thread on the other end for mating with a conduit coupling nut; or to establish necessary mechanical accommodations between an electrical conduit, conduit assembly and an electrical connector. Excludes REDUCING WASHER, KNOCKOUT and BOX CONNECTOR, ELECTRICAL. See also ADAPTER, CABLE TO CONNECTOR; and CHASE NIPPLE, CONDUIT.
What is an Electrical Conduit Sealing Fitting? 56 Items: An Electrical Conduit Sealing Fitting (SEALING FITTING,ELECTRICAL CONDUIT) is an item of metallic composition with a chamber for sealing compound and two hubs to accommodate electrical conduits of specified sizes. This item is designed with a filler hole and a removable screw plug to enable the pouring of sealing compound into the chamber for the purpose of preventing the passage of explosive gases through a conduit run. The item is primarily designed for use in hazardous locations and may be designed for vertical use, horizontal use, or both. For items which permit the connection or termination of wires, see POTHEAD. See also COUPLING, ELECTRICAL CONDUIT.
What is a Knockout Reducing Washer? 38 Items: A Knockout Reducing Washer (REDUCING WASHER,KNOCKOUT) is an item consisting of a flat, cupped or embossed metallic disk with a centerhole to fit an electrical conduit of a specified size and which is specifically designed to reduce the knockout opening in a box, panel, or wireway for the convenience of terminating electrical conduit of smaller size than the knockout. Excludes ADAPTER, ELECTRICAL CONDUIT.
What is an Electrical Conduit Nipple? 143 Items: An Electrical Conduit Nipple (NIPPLE,ELECTRICAL CONDUIT) is a nipple made of electrical conduit.
What is an Electrical Entrance Elbow? 34 Items: An Electrical Entrance Elbow (ENTRANCE ELBOW,ELECTRICAL) is an item of metallic composition cast in the form of an elbow, which is primarily intended to provide for the angular entrance of wires into a building, structure, or enclosure. This item, specifically designed for installation in exposed locations, has two hubs of a specified size to fit the service entrance conduit and may have a third hub for a driven ground connection. It has a cover which makes it tamper-proof and weather-resistant. It may include facilities for pulling electrical conductors but does not have facilities for mounting wiring devices.
What is an Electrical Conduit Bushing? 290 Items: An Electrical Conduit Bushing (BUSHING,ELECTRICAL CONDUIT) is an item of metal and/or insulating material having internal threads designed to fit over the end of electrical conduit and/or fittings to provide a smooth interior with a rounded edge to prevent damage to the insulation of the wire or cable emerging therefrom. It may be designed to fit over the end of thin wall conduit, and to be fitted with holding (staking) screws, or it may be provided with internal straight threads for attaching to thick wall electrical conduit or fittings. It may be fitted with a temporary knockout cap (bushcap), and grounding or bonding facilities. For externally threaded items, see BOX CONNECTOR, ELECTRICAL; BUSHING, ELECTRICAL CONDUCTOR; CHASE NIPPLE, CONDUIT and BUSHING, STRAIN RELIEF, CABLE. See also FERRULE, ELECTRICAL CONDUIT. Excludes plain sleeve bushings.
What is an Electrical Conduit Bondnut? 17 Items: An Electrical Conduit Bondnut (BONDNUT,ELECTRICAL CONDUIT) is an item of metallic composition, with internal threads, designed to fit the external threads of an electrical conduit or fitting, and which, when installed, provides a method of tightening and locking the connection and completes a positive bond between the conduit and apparatus or fitting to which connected. The bonding or grounding action is accomplished by sharp beveled teeth or by a screw(s). See also LOCKNUT, ELECTRICAL CONDUIT and NUT, COUPLING, ELECTRICAL CONDUIT.
What is an Electrical Conduit Union? 130 Items: An Electrical Conduit Union (UNION,ELECTRICAL CONDUIT) is an item comprising three members, so constructed that one of the members holds the remaining two in a fixed butted position; generally used to connect two conduits, conduit fittings, or a conduit and a conduit fitting in such a manner that they may be disconnected without disturbing the rest of the conduit line. See also COUPLING, ELECTRICAL CONDUIT.
What is an Electrical Conduit Elbow? 419 Items: An Electrical Conduit Elbow (ELBOW,ELECTRICAL CONDUIT) is an item fabricated in the form of an elbow and having both ends threaded female, or with unthreaded connecting facilities on both ends, or connecting facilities on both ends, one of which is a male thread without boss or shoulder. If a locknut or bondnut is included, it shall not be considered as a thread boss or shoulder. It is primarily intended to connect conduit to conduit. It may have a removable cover to facilitate pulling wires, but does not include facilities for mounting wiring devices. For items having a removable cover to facilitate pulling wires and specifically designed for close installation in exposed outdoor locations and which may have facilities for an outside driven ground, see ENTRANCE ELBOW, ELECTRICAL. For items with one end having a male thread with a boss or shoulder, see BOX CONNECTOR, ELECTRICAL. For items having a removable screw cap for pulling wires, with the cap positioned 45 degrees from the connection facilities, see ENTRANCE ELBOW, ELECTRICAL. For items fabricated in the form of an elbow having both ends threaded male, see BEND, ELECTRICAL CONDUIT.
What is a Conduit Outlet? 985 Items: A Conduit Outlet is an item designed to be used in a conduit system for the purpose of providing outlets or attachments for electrical wiring devices and/or designed to provide access and facilitate installment of wires. It may or may not include a cover(s). It does not include wiring devices. Excludes ENTRANCE ELBOW, ELECTRICAL. See also JUNCTION BOX.
What is an Electrical Conduit Bend? 118 Items: An Electrical Conduit Bend (BEND,ELECTRICAL CONDUIT) is an item fabricated in the form of a curved section specifically designed to mechanically join a conduit or conduit fitting to another conduit or conduit fitting. Items of this type do not have a boss or hub at either end, nor do they have facilities for mounting wiring devices or pulling electrical conductors. See also ELBOW, ELECTRICAL CONDUIT and CONDUIT OUTLET.
What is an Electrical Wall Plate? 595 Items: An Electrical Wall Plate (PLATE,WALL,ELECTRICAL) is an item designed to mount directly on a bracket or an electrical current carrying wiring device(s) such as switch(es) or outlet(s) (receptacle). The bracket(s) or electrical current carrying device is mounted in a JUNCTION BOX. For trade designated items designed to be attached directly on or through a bracket or electrical wiring device to a CONDUIT OUTLET, see COVER, CONDUIT OUTLET. For items designed for mounting directly on a JUNCTION BOX, see COVER, JUNCTION BOX.
What is an Interconnecting Box? 482 Items: An Interconnecting Box is an inclosure which includes mounts and protects such items as switches, circuit breakers, jacks, fuseholders, connectors, terminals and/or terminal boards, resistors, capacitors, transformers, and the like. It is primarily designed to interconnect two or more electrical and/or electronic items, except primary power source(s) such as generator(s) and battery(ies). It may include a cover or door. For inclosures which connect one or more primary power source(s) to one or more electrical and/or electronic item(s), see DISTRIBUTION BOX. See also CIRCUIT BREAKER BOX; TERMINAL BOX and INTERCONNECTING CABINET.
What is a Pole Step? 13 Items: A Pole Step (STEP,POLE) is an item designed to be used as a foot rest in ascending and descending utility poles, when attached thereto.
What is an Interior Cable Rack? 78 Items: An Interior Cable Rack (RACK,CABLE,INTERIOR) is an open frame structure primarily designed to support electrical cables in buildings and shelters. Its purpose is to provide, by itself or by joining to similar structures, a path or runway for cable which may connect two or more pieces of electrical equipment. It does not include items designed to hold a single cable. See also RACK, CABLE, UNDERGROUND; and HANGER, CABLE.
What is an Electrical Conduit Ferrule? 274 Items: An Electrical Conduit Ferrule (FERRULE,ELECTRICAL CONDUIT) is an item usually of one piece construction, but which may be comprised of more than one piece, designed to be affixed permanently or temporarily to the end of an electrical conduit to form an end fitting. Unflanged items form a permanent end fitting which affords mechanical protection to emerging conductors. Flanged items are used with another fitting normally a conduit coupling nut, to make the conduit adaptable for connection to an electrical connector, junction box or other conduit accessory or fitting. Excludes RING, ELECTRICAL BONDING; BUSHING, ELECTRICAL CONDUIT; and BUSHING, PLAIN SLEEVE. See also FERRULE-NUT COUPLING, ELECTRICAL CONDUIT.
What is an Underground Cable Rack Hook? 13 Items: An Underground Cable Rack Hook (HOOK,UNDERGROUND CABLE RACK) is a rigid item designed to be perpendicularly attached to an underground cable rack to be used as the supporting arm for cables. May include insulators.
What is an Electrical Conduit End Seal Disk? 28 Items: An Electrical Conduit End Seal Disk (DISK,END SEAL,ELECTRICAL CONDUIT) is a flat circular item fitted on the end of an electrical conduit in order to close the end to prevent the entrance of water or refuse, prior to installation of the wires, during shipment and/or construction. The item may be held in place by means of a conduit bushing and may be easily removed to permit installation of the wires.
What is a Cable Spacer? 104 Items: A Cable Spacer (SPACER,CABLE) is an item constructed specifically to provide a separation between lashed lead covered cable and messenger strand for the prevention of injury to sheath of cable.
What is an Electrical Box Connector? 1449 Items: An Electrical Box Connector (BOX CONNECTOR,ELECTRICAL) is an item designed to mechanically connect in a straight line or an angle electrical conduit, conduit assemblies, wire, wireway, cable, or cable assemblies to a point of termination, such as a junction box, conduit outlet, or the like. The termination end must have an external thread with a boss or shoulder and may be furnished with a locknut or bondnut; or, must have internal thread with which is furnished an externally threaded hub with a wrenching feature; or be of a snap-in type that may be installed from either inside or outside the box and secured with a captive screw. It is not intended to join conduit to conduit. For angle type items having a male thread without a boss or shoulder, see ELBOW, ELECTRICAL CONDUIT. Does not include facilities to mount wiring devices. Excludes CHASE NIPPLE, CONDUIT.
What is an Electrical Conduit Coupling? 391 Items: An Electrical Conduit Coupling (COUPLING,ELECTRICAL CONDUIT) is an item specifically designed and constructed to mechanically connect in a straight line two sections of electrical conduit or like fabrication and of the same size. For three-piece items which may be disassembled without disturbing the rest of the conduit line, see UNION, ELECTRICAL CONDUIT. See also ADAPTER, ELECTRICAL CONDUIT; POTHEAD; and SEALING FITTING, ELECTRICAL CONDUIT.
What is an Electrical Conduit Wye? 167 Items: An Electrical Conduit Wye (WYE,ELECTRICAL CONDUIT) is a type of electrical conduit fitting fabricated in the form of the letter Y, having three hubs permitting conduits and/or conduit fittings to be taken off laterally from the main line of equal degree on each side, or with the main line continuing straight with a branch taking off at an angle. For items of this type having facilities for mounting wiring devices, see CONDUIT OUTLET.
What is a Cable Rack Extension? 17 Items: A Cable Rack Extension (EXTENSION,CABLE RACK) is a metallic irregularly shaped item designed to permit cable racks to be mounted away from the mounting surface to escape obstructions or limited space.
What is an Electrical Bonding Ring? 79 Items: An Electrical Bonding Ring (RING,ELECTRICAL BONDING) is an item of metallic composition, usually round and flat with a center hole or slotted hole designed to accommodate an electrical cable or conduit, and which, when used in conjunction with a cable clamp or similar locking device, completes a positive bond between the cable or conduit fitting, such as connectors, adapters, and couplings, and the cable or conduit shield and/or individual conductor shield(s). See also FERRULE, ELECTRICAL CONDUCTOR.
What is an Electrical Equipment Rack Base? 123 Items: An Electrical Equipment Rack Base (BASE,ELECTRICAL EQUIPMENT RACK) is a structural item which is specifically designed to provide a suitable flat surface to support one or more RACK, ELECTRICAL EQUIPMENT. It may include legs and/or leveling devices. For similar items designed primarily for the purpose of damping shock and/or vibration, see MOUNTING BASE, ELECTRICAL EQUIPMENT. See also STAND, (as modified).
What is an Electrical Cable Splice Protector? 33 Items: An Electrical Cable Splice Protector (PROTECTOR,SPLICE,ELECTRICAL CABLE) is an item specifically designed to be mechanically fastened to an electrical cable on each end of a splice to protect the splice from excessive strain. It usually has provisions for making a waterproof or moisture-proof joint. Excludes INSULATION SLEEVING, ELECTRICAL.
What is an Electrical Conduit Coupling Nut? 193 Items: An Electrical Conduit Coupling Nut (NUT,COUPLING,ELECTRICAL CONDUIT) is an item of metallic composition with internal threads and an internal seat designed to join a ferrule capped conduit to a fitting. See also BONDNUT, ELECTRICAL CONDUIT.
What is an Insulator Bracket Strap? 18 Items: An Insulator Bracket Strap (STRAP,INSULATOR BRACKET) is an item specifically designed to reinforce insulator brackets at their fastenings on a line construction pole when high strength wire or long spans are used.
What is a Junction Box Cover? 552 Items: A Junction Box Cover (COVER,JUNCTION BOX) is a cover containing facilities for mounting directly on a JUNCTION BOX. It may have provisions for the insertion and/or mounting of electrical devices, such as switches, connectors, additional covers, and jewels. It may include the jewel(s). For covers having facilities for mounting on brackets or on current carrying devices such as switches and receptacle connectors, see PLATE, WALL, ELECTRICAL. See also COVER, CONDUIT OUTLET.
What is a Wire Strand Hanger? 27 Items: A Wire Strand Hanger (HANGER,WIRE STRAND) is a metallic item, grooved to fit a wire strand such as a messenger strand, and designed to be attached to a utility pole or other supporting surface for the purpose of horizontally suspending and firmly securing the wire strand. See also HANGER, CABLE, and CLAMP, ELECTRICAL CONDUCTOR, STRAIN. Excludes BRACKET, PIPE.
What is an Electrical Conduit Cross? 10 Items: An Electrical Conduit Cross (CROSS,ELECTRICAL CONDUIT) is a type of electrical conduit fitting fabricated in the form of a cross having four hubs in the same plane, the axes of which form a right angle, and primarily intended to join electrical conduits and/or conduit fittings. For items of this type having ties for mounting wiring devices, see CONDUIT OUTLET.
What is an Electrical Conduit Tee? 84 Items: An Electrical Conduit Tee (TEE,ELECTRICAL CONDUIT) is a type of electrical conduit fitting fabricated in the form of the letter T having three hubs for joining electrical conduits and/or conduit fittings. For items of this type having facilities for mounting wiring devices, see CONDUIT OUTLET.
What is a Blank Panel? 1873 Items: A Blank Panel (PANEL,BLANK) is a panel designed to fill a space not occupied by actual operating components, and may have instructions, component designations, or component identifications etched or printed thereon.
Case,Electrical Equipment Cabinet 73 Items
Case,Switch Box 44 Items
What is a Ground Rod Section? 30 Items: A Ground Rod Section (ROD SECTION,GROUND) is an item which is part of a multi-section ground rod. Excludes items with driving points. see also ROD, GROUND.
What is a Junction Box Extension? 71 Items: A Junction Box Extension (EXTENSION,JUNCTION BOX) is an item designed to be mounted on a JUNCTION BOX to increase the depth of the box.
What is a Stuffing Tube Packing Nut? 87 Items: A Stuffing Tube Packing Nut (PACKING NUT,STUFFING TUBE) is a threaded or unthreaded device, with an unthreaded center hole to accommodate an electrical cable or tube, designed to mate with the threads or sealing components of a stuffing tube body for the purpose of compressing packing around the electrical cable or tube. A component of a STUFFING TUBE.
What is a Transmission Line Grounding Set? 38 Items: A Transmission Line Grounding Set (GROUNDING SET,TRANSMISSION LINE) is an item consisting of two or more clamp type devices with facilities for the connection of jumpers and/or grounding cables. When installed this item provides for the temporary grounding of de-energized electrical transmission line(s) to protect workmen against injury resulting from accidental re-energization of the lines. Excludes CLAMP, ELECTRICAL.
What is a Cable Marker Sleeve? 1191 Items: A Cable Marker Sleeve (SLEEVE,MARKER,CABLE) is a cylindrical item into which a wire or cable is inserted. It is inscribed for identification, to indicate connections or routing of electrical cables and the like. For unmarked items made of insulation material, see INSULATION SLEEVING, ELECTRICAL. For items secured by crimping, slot and tongue, or other similar methods of fastening, see BAND, MARKER.
What is an Electrical Standardized Components Case? 81 Items: An Electrical Standardized Components Case (CASE,STANDARDIZED COMPONENTS,ELECTRICAL) is a case which by virtue of standardization of equipment dimensions is designed to contain one or more components of different basic names. Do not use for cases designed only for specific items or a specific grouping of items.
What is an Electrical Conduit Ferrule-Nut Coupling? 21 Items: An Electrical Conduit Ferrule-Nut Coupling (FERRULE-NUT COUPLING,ELECTRICAL CONDUIT) is an item consisting of a FERRULE, ELECTRICAL CONDUIT upon which is permanently mounted a NUT, COUPLING, ELECTRICAL CONDUIT. It is designed to be attached to an electrical conduit and used to mechanically connect the conduit to another conduit fitting such as a box connector. Excludes BOX CONNECTOR, ELECTRICAL; ADAPTER, ELECTRICAL CONDUIT; and COUPLING, ELECTRICAL CONDUIT.
What is a Strain Electrical Conductor Clamp? 472 Items: A Strain Electrical Conductor Clamp (CLAMP,ELECTRICAL CONDUCTOR,STRAIN) is a clamp designed to support and/or dead end a suspended conductor(s). Must have a provision for attachment to an insulator. Insulator is not included. Excludes HANGER, WIRE STRAND.
What is an Electrical Entrance Cap Shell? 11 Items: An Electrical Entrance Cap Shell (SHELL,ELECTRICAL ENTRANCE CAP) is an item similar to ENTRANCE CAP, ELECTRICAL, but it does not include an insulating block. See also CAP, ELECTRICAL.
What is a Flexible Metal Conduit? 564 Items: A Flexible Metal Conduit (CONDUIT,METAL,FLEXIBLE) is a conduit constructed of circular flexible metal tubing. It may be shielded with a woven metal wire braid covering, with a packing between the joints, and it may have a rubber and/or synthetic rubber or plastic outer protective covering. It contains no fittings. See also CONDUIT, METAL, RIGID. Excludes conduit like items that are designed for other than electrical applications.
What is a Rigid Metal Conduit? 512 Items: A Rigid Metal Conduit (CONDUIT,METAL,RIGID) is a conduit of one-piece tubular construction, designed as thin wall type (EMT) and thick wall type. The items may be threaded and furnished with a COUPLING, ELECTRICAL CONDUIT and/or thread protection. See also CONDUIT ASSEMBLY,METAL, RIGID. Excludes conduit like items that are designed for other than electrical applications.
What is a Rigid Nonmetallic Conduit? 111 Items: A Rigid Nonmetallic Conduit (CONDUIT,NONMETALLIC,RIGID) is a conduit of one piece construction of asbestos and cement, bituminized fiber, or rigid plastics material. The item may have both ends processed for connection by means of a coupling. One coupling may be furnished for each length of conduit. The conduit may or may not be impregnated with coal tar pitch. Excludes conduit like items that are designed for other than electrical applications.
What is a Radio Frequency Cable Splicing Kit? 25 Items: A Radio Frequency Cable Splicing Kit (SPLICING KIT,RADIO FREQUENCY CABLE) is a collection of items used in splicing a radio frequency cable, such as yokes, plugs, cable, switches, and power transformer.
What is a Drive Ring? 10 Items: A Drive Ring is a metal item having an eye attached or integral with a nail-like item. It is designed for running twisted pair, bridle, or parallel drop wires on building walls, fences, poles and the like. For similar items having threaded ends, see BRIDLE RING. Excludes HOOK, SUPPORT.
What is a Bridle Ring? 12 Items: A Bridle Ring is a metal item having an open eye on one end and a wood screw, or machine thread on the opposite end. The machine thread item may be furnished with a nut or toggle attachment. It is designed for running twisted pair, bridle or parallel drop wires on building walls, fences, poles, and the like. For similar items having a drive nail end, see DRIVE RING. Excludes HOOK, SUPPORT.
What is an Electrical Equipment Leg? 151 Items: An Electrical Equipment Leg (LEG,ELECTRICAL EQUIPMENT) is an item which, in conjunction with one or more similar items, aids in the support of electrical equipment. See also LEG SECTION, ELECTRICAL EQUIPMENT.
What is an Electrical Equipment Leg Section? 60 Items: An Electrical Equipment Leg Section (LEG SECTION,ELECTRICAL EQUIPMENT) is an item which in itself is not a complete functioning item. It consists of parts which, together with other similar parts, form an electrical equipment leg.
What is a Conduit Chase Nipple? 86 Items: A Conduit Chase Nipple (CHASE NIPPLE,CONDUIT) is an externally threaded item having a hexagonal shoulder with a smooth bore. It may be used to connect two junction boxes or to accommodate thin wall conduit or tubing by slip fit to a junction box or conduit outlet. It may or may not be furnished with a locknut. For items externally and internally threaded, see ADAPTER, ELECTRICAL CONDUIT. See also BUSHING, ELECTRICAL CONDUCTOR.
What is a Cable Strain Relief Bushing? 299 Items: A Cable Strain Relief Bushing (BUSHING,STRAIN RELIEF,CABLE) is an insulating item designed to prevent movement along the axis of an electric wire or cable in either direction when placed in the chassis of such items as electric fans, irons, drills, motors, radios, clocks and the like. It may be designed for use in the central column of a gun mount and the like. See also COLLAR, CABLE.
What is an Electrical Nonmetallic Conduit Assembly? 1312 Items: An Electrical Nonmetallic Conduit Assembly (CONDUIT ASSEMBLY,NONMETALLIC,ELECTRICAL) is a specific length of tubing or conduit, nonmetallic, rigid or flexible, with or without electrical rating, and with permanently attached ferrule(s), coupling nut(s), or the like. It may include one or more woven wire braid cover(s). Excludes detachable fittings such as tee(s), wye(s) or elbow(s). Also excludes conduit like items that are designed for other than electrical applications.
What is a Conduit Outlet Cover? 383 Items: A Conduit Outlet Cover (COVER,CONDUIT OUTLET) is an item of any material, with or without threads, designed to mate with a CONDUIT OUTLET or a SEALING FITTING, ELECTRICAL CONDUIT. It may be designed as a removable side plate cover with or without hubs. It may have provisions for draining or venting. It may be designed for the insertion and/or mounting of electrical devices, such as switches, receptacle connectors, and indicator light lenses. It may include mechanisms for the external operation of switches but does not include the wiring devices. For items designed to mount directly on a bracket or an electrical current carrying wiring device, see PLATE, WALL, ELECTRICAL. See also COVER, JUNCTION BOX.
What is an Electrical Conduit Coupling Nut Clamp? 44 Items: An Electrical Conduit Coupling Nut Clamp (CLAMP,COUPLING NUT,ELECTRICAL CONDUIT) is an item designed to be clamped on a conduit. It has extending prongs to engage and lock in position a NUT, COUPLING, ELECTRICAL CONDUIT.
What is an Electrical Equipment Shelf? 676 Items: An Electrical Equipment Shelf (SHELF,ELECTRICAL EQUIPMENT) is an item relatively thin in its vertical dimension, designed to provide a horizontal working surface on the front of a CABINET, ELECTRICAL EQUIPMENT or a RACK, ELECTRICAL EQUIPMENT. May include wiring, power outlets and similar accessories. May be furnished with slides to permit stowing within the cabinet or rack when not in actual use.
What is a Shop Set Installation Electrical Kit? 23 Items: A Shop Set Installation Electrical Kit (ELECTRICAL KIT,SHOP SET INSTALLATION) is a collection of wiring and fixture items, such as box, cable, connector, cord, cover, cutout, fuse, receptacle, socket, switch, and the like, designed to wire shop set equipment when installing it in a shop truck as part of the basic load.
What is a Line Supporting Strap? 16 Items: A Line Supporting Strap (STRAP,LINE SUPPORTING) is a flexible strap, furnished with a buckle, specificifically designed to support other items, such as cable(s), wire(s), tube(s), and the like. The buckle may be permanently assembled and may be provided with a mounting feature. The strap may be used to bridge a channel by mounting the buckle and strap separately. Excludes CLAMP, LOOP; STRAP, RETAINING; STRAP, LEATHER; and STRAP, WEBBING.
What is an Electrical Conduit Locknut? 202 Items: An Electrical Conduit Locknut (LOCKNUT,ELECTRICAL CONDUIT) is an item having internal threads designed to fit the external threads of an electrical conduit or fitting for connecting to a junction box, panel, wireway, or other point of termination, and which, when installed, provides a method of tightening to lock the connection. The items may be either flat-sided or circular in external shape and must have a specific conduit size designation. SEE BONDNUT, ELECTRICAL CONDUIT and LOCKNUT, TUBE FITTING. Excludes NU T (1), PLAIN HEXAGON.
What is a Flexible Nonmetallic Conduit? 657 Items: A Flexible Nonmetallic Conduit (CONDUIT,NONMETALLIC,FLEXIBLE) is a conduit of one piece flexible, nonmetallic, tubular construction. The item may have an outer covering for additional mechanical protection, a woven wire braid for interference suppression, and/or wire reinforcement. For items having rated electrical characteristics, see INSULATION SLEEVING, ELECTRICAL. Excludes TUBING, NONMETALLIC; and TUBING, PLASTIC, SPIRAL WRAP. Excludes conduit like items that are designed for other than electrical applications.
What is an Electrical Equipment Drawer? 518 Items: An Electrical Equipment Drawer (DRAWER,ELECTRICAL EQUIPMENT) is an item designed to slide in and out of a CABINET, ELECTRICAL EQUIPMENT or RACK, ELECTRICAL EQUIPMENT and used to mount and/or store electrical/electronic equipment. It does not include the electrical/electronic equipment, but may include wires, cables, terminal boards, connectors, etc.
What is an Electrical Equipment Mounting Base? 3161 Items: An Electrical Equipment Mounting Base (MOUNTING BASE,ELECTRICAL EQUIPMENT) is a tray or racklike item designed to provide a supporting surface to which electrical/electronic equipment may be secured when installed in aircraft, vehicles, or other types of mobile equipment. It may be equipped with shock or vibration isolation devices and/or wires, cables, terminal boards, connectors, etc. Excludes BASE, ELECTRICAL EQUIPMENT RACK and MOUNT, RESILIENT. See also RACK, ELECTRICAL EQUIPMENT.
What is an Electronic Junction Rack? 253 Items: An Electronic Junction Rack (RACK,ELECTRONIC JUNCTION) is an open frame structure specifically designed to accommodate (but does not include) electronic terminal junctions (TERMINAL BOARD; TERMINAL (1), FEEDTHRU; and the like). The item may consist of separable or nonseparable channels, mounting blocks and fastening devices. Mounting blocks are designed so the assembly can be mounted on panels or bulkheads. Tightening the fastening devices which secure the channels to the mounting blocks will also secure terminal junctions within the frame assembly. Excludes RACK, ELECTRICAL EQUIPMENT; TERMINAL BOARD; JUNCTION BOX; and HARDWARE KIT, ELECTRONIC EQUIPMENT.
What is a Safety Shorting Probe? 16 Items: A Safety Shorting Probe (PROBE,SAFETY SHORTING) is a device used to discharge the voltage stored in cathode ray tubes and other electronic equipment which have capacitor type filtering circuits that retain a voltage charge after the primary power has been removed. See also DISCHARGER, ELECTROSTATIC.
What is an Electrical Tie Down Mounting Base? 626 Items: An Electrical Tie Down Mounting Base (MOUNTING BASE,TIE DOWN,ELECTRICAL) is an item used in conjunction with STRAP, TIEDOWN, ELECTRICAL COMPONENTS to secure wire(s) or cable(s) to a supporting surface.
What is a Raceway Cover? 196 Items: A Raceway Cover (COVER,RACEWAY) is an item used in conjunction with open style raceway for the protection of electrical wires and/or cables. May be attached by snap closure, stud and nut, or similar device. Generally furnished in bulk quantities.
Raceway,Metallic 376 Items
Raceway,Nonmetallic 122 Items
What is an Electrical-Electronic Equipment Panel? 2447 Items: An Electrical-Electronic Equipment Panel (PANEL,ELECTRICAL-ELECTRONIC EQUIPMENT) is a panel which is designed to accommodate, but does not include connectors, displays, indicators, jacks, meters, switches, and the like. It may include clinch nuts or fastening devices as part of the item. Excludes PANEL, BLANK.
What is an Electric Cable Joint Box Supplementary Equipment? 14 Items: An Electric Cable Joint Box Supplementary Equipment (SUPPLEMENTARY EQUIPMENT,JOINT BOX,ELECTRIC CABLE) is a pre-determined combination of different accessories which are packed as a set and are used as supplement to the normal assembly accessories of the JOINT BOX, ELECTRIC CABLE.
What is an Electrical-Electronic Equipment Chassis? 5595 Items: An Electrical-Electronic Equipment Chassis (CHASSIS,ELECTRICAL-ELECTRONIC EQUIPMENT) is a box, frame, or plate fabricated of electrically conductive material designed to mount, but which does not include, electronic components and their associated circuitry. It may have facilities for attachment to a rack or cabinet or to accommodate specially designed components. It may include a shielding function, integral wiring, and mounting hardware as part of the item. Excludes MOUNTING BASE, ELECTRICAL EQUIPMENT.
What is a Mounting Plate? 324 Items: A Mounting Plate (PLATE,MOUNTING) is a metallic or nonmetallic item which is rigid, flat and generally smooth. Its thickness is small in comparison to its length and width. It is designed for mounting another item and may have drilled or threaded holes or other facilities for mounting to a supporting object or surface. See SUPPORT, as modified. Do not use if a more specific name applies.
What is an Electrical Conduit Ferrule Anchor Plate? 13 Items: An Electrical Conduit Ferrule Anchor Plate (ANCHOR PLATE,ELECTRICAL CONDUIT FERRULE) is a piece of flat material, specially designed to secure a FERRULE, ELECTRICAL CONDUIT.
What is a Nonmetallic Raceway Assembly? 39 Items: A Nonmetallic Raceway Assembly (RACEWAY ASSEMBLY,NONMETALLIC) is a channel consisting of one or more parts with other than circular cross sections. The item forms part of bulk quantities which have been specially treated and provided with miter heads and/or mounting holes, for example. It may also be produced in one piece by special molding processes such as thermoplastic pressure die-casting. The item protects electrical wires and/or cables against mechanical damage. Excludes RACEWAY (1), NONMETALLIC.
What is a Metallic Raceway Assembly? 149 Items: A Metallic Raceway Assembly (RACEWAY ASSEMBLY,METALLIC) is a channel consisting of one or more parts with other than circular cross sections. The item is not supplied in bulk quantities and has a particular shape with specific dimensions conforming to a predetermined cable run (e.g., angular or U-shape). The item protects cables against damage. Excludes RACEWAY (1), METALLIC.
What is an Electrical Box Sealing Flange? 10 Items: An Electrical Box Sealing Flange (FLANGE,SEALING,ELECTRICAL BOX) is an item designed for tightly sealing those openings of a JUNCTION BOX towards the outside or inside that are neither provided for being connected with other JUNCTION BOX nor for cable entry. Excludes FLANGE, ADAPTER, ELECTRICAL BOX and FLANGE, ELECTRICAL BOX ENTRY.
What is an Electrical Box Entry Flange? 15 Items: An Electrical Box Entry Flange (FLANGE,ELECTRICAL BOX ENTRY) is an item designed for tightly sealing the openings of a JUNCTION BOX, provided for cable entry, towards the inside or outside. It may include openings or knock-out holes with or without threads that are provided for the installation of STUFFING TUBE or other cable entries. Excludes FLANGE, SEALING, ELECTRICAL BOX and FLANGE, ADAPTER, ELECTRICAL BOX.
What is an Electrical Equipment Foot? 90 Items: An Electrical Equipment Foot (FOOT,ELECTRICAL EQUIPMENT) is an item which in conjunction with an electrical equipment leg or the like, aids in the support of electrical equipment. It is a broad based metallic or nonmetallic item which serves as a stabilizer.
What is an Electrical Standardized Components Case Section? 21 Items: An Electrical Standardized Components Case Section (CASE SECTION,STANDARDIZED COMPONENTS,ELECTRICAL) is an item of various shapes or design representing an integral part of a CASE (2), STANDARDIZED COMPONENTS, ELECTRICAL. It may include fastening, sealing, padding and/or locking devices. It does not include components.
What is a Guide Rail? 228 Items: A Guide Rail (RAIL,GUIDE) is an item used for fixing/mounting TERMINAL JUNCTION BLOCK, SECTIONAL.
What is an Electronic Equipment Mounting Tray? 946 Items: An Electronic Equipment Mounting Tray (TRAY,MOUNTING,ELECTRONIC EQUIPMENT) is an item which facilitates the mounting of electronic/electrical equipment(s) into racks and the like, having holes and/or clamping devices enabling quick replacement of the mounted equipment. does not include the equipment for which designed. may include interconnecting facilities and resilient mountings. excludes DRAWER, ELECTRICAL EQUIPMENT, RACK MOUNTED; DRAWER, ELECTRICAL EQUIPMENT CABINET; CHASSIS, ELECTRICAL EQUIPMENT and PLATE, MOUNTING, ELECTRICAL EQUIPMENT.
What is an Electrical Conductor Protector? 25 Items: An Electrical Conductor Protector (PROTECTOR,ELECTRICAL CONDUCTOR) is an item designed to be interposed between an electrical conductor which may be bare or insulated and its support or housing to prevent chafing caused by contraction and expansion due to changes in the ambient temperature or damage or injury from outside sources. Excludes such items as loom, cotton sleeving, rubber blankets, grade clamps, and all types of conduit and INSULATION SLEEVING, ELECTRICAL.
What is an Electrical Fitting Mounting Base? 92 Items: An Electrical Fitting Mounting Base (BASE,MOUNTING,ELECTRICAL FITTING) is an item serving as a base for electrical pieces such as switches, ceiling roses. It is usually recessed at the base for accommodating wires.
What is a Rigid Metal Conduit Assembly? 597 Items: A Rigid Metal Conduit Assembly (CONDUIT ASSEMBLY,METAL,RIGID) is a straight or prebent length of a CONDUIT, METAL, RIGID complete with permanently attached fitting(s), such as flanges, wye(s) and tee(s). See also TUBE ASSEMBLY, METAL and CASING (as modified). Excludes conduit like items that are designed for other than electrical applications.
What is an Interconnecting Cabinet? 41 Items: An Interconnecting Cabinet is an enclosure, the principal purpose of which is to house, protect, and provide a connecting or branching point for one or more electrical circuits. It is wired to provide the interconnecting facilities for a specific group of electrical and/or electronic items outside of the interconnecting cabinet. It may contain parts such as capacitors, resistors, fuses, relays and terminal boards. In addition, it includes panel(s) on which are mounted control and instrumenation devices associated with the internal components of the cabinet. For items not including such panels. See CABINET, ELECTRICAL EQUIPMENT. See also CIRCUIT BREAKER BOX; DISTRIBUTION BOX; INTERCONNECTING BOX; JUNCTION BOX and TERMINAL BOX.
What is an Electrical Cable Assembly Protector? 74 Items: An Electrical Cable Assembly Protector (PROTECTOR,ELECTRICAL CABLE ASSEMBLY) is an item specifically designed to protect an electrical cable assembly from damage by other items during assembly and/or disassembly operations of associated equipment. Excludes such items as loom, cotton sleeving, rubber blankets, all types of conduit, INSULATION SLEEVING, ELECTRICAL and PROTECTOR, ELECTRICAL CABLE.
What is an Electrical Components Tie Down Strap? 2073 Items: An Electrical Components Tie Down Strap (STRAP,TIE DOWN,ELECTRICAL COMPONENTS) is a preformed item of flexible or semiflexible material of various cross-sectional shapes. It may be tapered to a point at one or both ends, or provided with holes, slots, detents, or other locking devices. It is designed to surround wiring harnesses and other electrical/electronic components. It may be preprinted with legendary characters, symbol(s), letter(s), numeral(s), or color coded, and may be provided with means for securing to other objects. Excludes BAND, MARKER; CLAMP, ELECTRICAL; CLAMP, LOOP; MARKER, IDENTIFICATION; and STRAP, RETAINING.
What is an Electric Component Rail Guide Stop? 15 Items: An Electric Component Rail Guide Stop (STOP,RAIL GUIDE,ELECTRIC COMPONENT) is a metallic or nonmetallic item or various shapes designed to be attached at the end of a RAIL,GUIDE to prevent movement of electric component. It may include facilities for a pin, set screw, or the like to allow for adjustment.
What is a Raceway End Cap? 12 Items: A Raceway End Cap (END CAP,RACEWAY) is an item which is used to close right and or left side of RACEWAY (WITH MODIFIER).
What is an Electrical Cable Ground Guard? 23 Items: An Electrical Cable Ground Guard (GUARD,GROUND,ELECTRICAL CABLE) is a metallic or nonmetallic item of various shape designed to be placed on floor to protect onr or several electrical cable or cord from damages caused by the personnel vehicular, equipment and the like. Excludes: PROTECTOR,ELECTRICAL CABLE and PROTECTOR,ELECTRICAL CABLE ASSEMBLY.

Stock Items From Supply Class 5975 Page 168 of 176

5975-01-616-5280
Cable Hanger

016165280
631660-B21: RNCC: 3 | RNVC: 2

19 Feb 2013

5975-01-616-0697
Electrical-Electronic Equipment Chassis

016160697
60-1011-01: RNCC: 3 | RNVC: 2

31 Jan 2013

5975-01-616-1092
Junction Box Cover

016161092
62744: RNCC: 3 | RNVC: 2
SMU-00000014: RNCC: 5 | RNVC: 2
62744: RNCC: 5 | RNVC: 2
62744: RNCC: 5 | RNVC: 9

1 Feb 2013

5975-01-078-4187
Outlet Assembly

010784187
5009-00: RNCC: 3 | RNVC: 2

13 Jun 1979

5975-01-079-4474
Blank Panel

010794474
842177-1: RNCC: 3 | RNVC: 2
842177-1: RNCC: 8 | RNVC: 2

6 Jul 1979

5975-01-678-7425
Rigid Metal Conduit

016787425
68A230605-2005: RNCC: 3 | RNVC: 2

22 Feb 2019

5975-01-678-7461
Electrical Equipment Rack

016787461
OG-X-FR: RNCC: 3 | RNVC: 2

22 Feb 2019

5975-01-677-8383
Electrical-Electronic Equipment Chassis

016778383
779218-B21: RNCC: 3 | RNVC: 2

9 Jan 2019

5975-01-677-4087
Electrical Equipment Mounting Base

016774087
MNT-SHELF-MX480-S: RNCC: 3 | RNVC: 2

12 Dec 2018

5975-01-678-0079
Electrical-Electronic Equipment Chassis

016780079
CHAS-BP3-MX480-S: RNCC: 3 | RNVC: 2

16 Jan 2019

5975-01-678-6929
Electrical-Electronic Equipment Chassis

016786929
CHAS-MX80-P-BB: RNCC: 3 | RNVC: 2
CHAS-MX80-P-BB: RNCC: 5 | RNVC: 2

20 Feb 2019

5975-01-678-6956
Electrical-Electronic Equipment Chassis

016786956
MX960BASE3-AC: RNCC: 3 | RNVC: 2
MX960BASE3-AC: RNCC: 5 | RNVC: 2

20 Feb 2019

5975-01-677-5471
Electrical-Electronic Equipment Chassis

016775471
CHAS-BP3-MX960-ECM-S: RNCC: 3 | RNVC: 2
CHAS-BP3-MX960-ECM-S: RNCC: 5 | RNVC: 2

19 Dec 2018

5975-01-376-2944
Flexible Metal Conduit Assembly

013762944
226490-DL0000: RNCC: 3 | RNVC: 2
17B2E2000-523: RNCC: 5 | RNVC: 2

29 May 1993

5975-01-376-3972
Electrical Conduit Elbow

013763972
MB326: RNCC: 3 | RNVC: 9

2 Jun 1993

5975-01-376-5770
Terminal Board

013765770
9D0090-5: RNCC: 3 | RNVC: 2

6 Jun 1993

5975-01-538-4033
Electrical-Electronic Equipment Chassis

015384033
842439-1: RNCC: 3 | RNVC: 2

21 Mar 2006

5975-01-538-6413
Electrical Equipment Rack

015386413
374493-B21: RNCC: 3 | RNVC: 2

28 Mar 2006

5975-01-536-2242
Electrical Conduit Wye

015362242
227273-FY00000A: RNCC: 3 | RNVC: 2

22 Dec 2005

5975-01-536-5093
Flexible Metal Conduit Assembly

015365093
227697-DL0000: RNCC: 3 | RNVC: 2

5 Jan 2006

5975-01-537-1300
Interconnecting Box

015371300
070688301: RNCC: 3 | RNVC: 2
2410LX96070688301: RNCC: C | RNVC: 1

26 Jan 2006

5975-01-632-0600
Junction Box

016320600
PS-J-BX: RNCC: 3 | RNVC: 2

6 Oct 2014

5975-01-632-9328
Electrical-Electronic Equipment Panel

016329328
3365446-1: RNCC: 3 | RNVC: 2

4 Nov 2014

5975-01-633-5073
Electrical-Electronic Equipment Panel

016335073
030814-0003: RNCC: 3 | RNVC: 2

25 Nov 2014

5975-01-633-1480
Electrical Equipment Cabinet

016331480
AR3107: RNCC: 3 | RNVC: 2
NETSHELTER SX 48U: RNCC: 5 | RNVC: 2

12 Nov 2014

5975-00-433-5901
Conduit Outlet Cover

004335901
DS150: RNCC: 3 | RNVC: 2

12 Feb 1972

5975-01-612-8246
Electrical-Electronic Equipment Chassis

016128246
F-1400: RNCC: 3 | RNVC: 2

22 Oct 2012

5975-01-614-8856
Electrical Equipment Rack

016148856
701M6615: RNCC: 3 | RNVC: 2

18 Dec 2012

5975-01-614-0953
Electrical-Electronic Equipment Chassis

016140953
WS-C6513-E: RNCC: 3 | RNVC: 2

27 Nov 2012

5975-01-068-7228
Receiver Handle

010687228
624-5945-002: RNCC: 3 | RNVC: 2

1 Dec 1978

5975-01-674-5750
Electrical-Electronic Equipment Chassis

016745750
ION106-D: RNCC: 3 | RNVC: 9
ION106-D: RNCC: 5 | RNVC: 2

2 Aug 2018

5975-01-674-5627
Raceway Cover

016745627
OCFX10IW-X: RNCC: 3 | RNVC: 2

1 Aug 2018

5975-01-673-9480
Electrical Cable Protector

016739480
62005878: RNCC: 3 | RNVC: 2

6 Jul 2018

5975-01-674-6988
Electrical Equipment Mounting Base

016746988
8499975-1: RNCC: 3 | RNVC: 2

7 Aug 2018

5975-01-675-2373
Electrical Components Tie Down Strap

016752373
BT2LH-L0: RNCC: 3 | RNVC: 2

29 Aug 2018

5975-01-675-5850
Electrical-Electronic Equipment Panel

016755850
10027-0028: RNCC: 3 | RNVC: 2

18 Sep 2018

5975-01-675-4380
Interior Cable Rack

016754380
000 044: RNCC: 3 | RNVC: 2

11 Sep 2018

5975-01-676-7613
Junction Box

016767613
SB-8-5: RNCC: 3 | RNVC: 2

9 Nov 2018

5975-01-373-9964
Cable Marker Sleeve

013739964
TRSA1014/E/5: RNCC: 3 | RNVC: 2
99045868: RNCC: 5 | RNVC: 2

14 Apr 1993

5975-01-374-8597
Electrical Tie Down Mounting Base

013748597
TM3R6-C: RNCC: 3 | RNVC: 2
5D0061-5: RNCC: 5 | RNVC: 2
TM3R6: RNCC: 5 | RNVC: 9

30 Apr 1993

5975-01-375-2945
Electrical-Electronic Equipment Chassis

013752945
L-LOT-V-1-71: RNCC: 3 | RNVC: 9

7 May 1993

5975-01-375-2946
Electrical-Electronic Equipment Chassis

013752946
074-500522-00: RNCC: 3 | RNVC: 2

7 May 1993

5975-01-536-2590
Electrical Equipment Rack

015362590
5HU50300-109: RNCC: 3 | RNVC: 2

23 Dec 2005

5975-01-536-1776
Flexible Metal Conduit Assembly

015361776
227713-DL0000: RNCC: 3 | RNVC: 2

22 Dec 2005

5975-01-536-2248
Flexible Metal Conduit

015362248
227715-DL0000: RNCC: 3 | RNVC: 2

22 Dec 2005

5975-01-536-2195
Electrical Equipment Rack

015362195
65000126: RNCC: 3 | RNVC: 2

22 Dec 2005

5975-01-536-9613
Electrical Grounding Plate

015369613
IJB1MSTRAY1000C-05: RNCC: 3 | RNVC: 2

20 Jan 2006

5975-01-537-2833
Cable Hanger

015372833
54-17169: RNCC: 3 | RNVC: 2
54-17169: RNCC: 5 | RNVC: 2
54-17169: RNCC: 5 | RNVC: 2

1 Feb 2006

5975-01-536-2340
Flexible Metal Conduit Assembly

015362340
230807-DL0000: RNCC: 3 | RNVC: 2

22 Dec 2005

5975-01-537-5598
Electrical-Electronic Equipment Chassis

015375598
DS-C9216A-K9: RNCC: 3 | RNVC: 2
MDS 9216A: RNCC: 5 | RNVC: 2

13 Feb 2006

5975-01-534-6060
Electronic Junction Rack

015346060
11472327-004: RNCC: 3 | RNVC: 2

26 Oct 2005

5975-01-535-3390
Cable Marker Sleeve

015353390
M235A774-160: RNCC: 3 | RNVC: 2

23 Nov 2005

5975-01-534-9441
Electrical-Electronic Equipment Chassis

015349441
5211605-07: RNCC: 3 | RNVC: 2

8 Nov 2005

5975-01-631-7552
Electrical-Electronic Equipment Chassis

016317552
TRC-190-AC: RNCC: 3 | RNVC: 2

24 Sep 2014

5975-00-432-9519
Electrical Conductor Bushing

004329519
0N089558-6: RNCC: 3 | RNVC: 2

4 Feb 1972

5975-01-672-3367
Electrical Equipment Mounting Base

016723367
622-8801-001: RNCC: 3 | RNVC: 2

27 Apr 2018

5975-01-534-1146
Telescoping Bushing

015341146
0700550046: RNCC: 3 | RNVC: 2

7 Oct 2005

5975-01-534-2405
Electrical-Electronic Equipment Chassis

015342405
160898-01: RNCC: 3 | RNVC: 2
160898-01: RNCC: 3 | RNVC: 9

13 Oct 2005

5975-01-535-4194
Electrical-Electronic Equipment Panel

015354194
80-0700-13: RNCC: 3 | RNVC: 2

29 Nov 2005

5975-01-534-7582
Electrical-Electronic Equipment Chassis

015347582
BA36R-RD: RNCC: 3 | RNVC: 9
00-BA356-RD: RNCC: 5 | RNVC: 2

1 Nov 2005

5975-01-535-0250
Electrical-Electronic Equipment Chassis

015350250
11477046: RNCC: 3 | RNVC: 2

10 Nov 2005

5975-01-534-9261
Electrical-Electronic Equipment Chassis

015349261
3424-1-110: RNCC: 3 | RNVC: 2

8 Nov 2005

5975-01-535-5521
Electrical Equipment Rack

015355521
7285702G001: RNCC: 3 | RNVC: 2

2 Dec 2005

5975-01-535-3391
Cable Marker Sleeve

015353391
M235A774-161: RNCC: 3 | RNVC: 2

23 Nov 2005

5975-01-535-1491
Blank Panel

015351491
11441692: RNCC: 3 | RNVC: 2

16 Nov 2005

5975-01-666-9948
Electrical-Electronic Equipment Panel

016669948
3365211-1: RNCC: 3 | RNVC: 2

28 Sep 2017

5975-01-667-5473
Electrical Fitting Mounting Base

016675473
7117102-1: RNCC: 3 | RNVC: 2

20 Oct 2017

5975-01-534-7115
Electrical-Electronic Equipment Panel

015347115
11464115: RNCC: 3 | RNVC: 2

31 Oct 2005

5975-01-121-6064
Hydraulic Retainer

011216064
344679-1: RNCC: 3 | RNVC: 2
344679-1: RNCC: 8 | RNVC: 2

6 Nov 1981

5975-01-368-3383
Electrical Box Connector

013683383
2255: RNCC: 3 | RNVC: 2
BS-72101: RNCC: D | RNVC: 9

29 Nov 1992

5975-01-531-9042
Insulation-Ac Blank

015319042
LA-RA24-4: RNCC: 3 | RNVC: 2

21 Jul 2005

5975-01-532-0528
Interconnecting Box

015320528
4HA0402-507: RNCC: 3 | RNVC: 2

26 Jul 2005

5975-01-533-0348
Electrical Equipment Mounting Base

015330348
16F3037-1: RNCC: 3 | RNVC: 2

29 Aug 2005

5975-01-665-0903
Electrical Conduit Coupling

016650903
CILBA-1-1/2: RNCC: 3 | RNVC: 2
4227-020-P02-1043: RNCC: 5 | RNVC: 2

19 Jul 2017

5975-01-665-0949
Electrical Equipment Leg

016650949
10020009-R-34094: RNCC: 3 | RNVC: 2
10020009-34094: RNCC: 5 | RNVC: 2

19 Jul 2017

5975-01-665-6205
Electrical Cable Protector

016656205
63-FCM48BK: RNCC: 3 | RNVC: 2
63-FCM48BK: RNCC: 3 | RNVC: 9

7 Aug 2017

5975-01-627-8994
Raceway Cover

016278994
HBLTT545RB: RNCC: 3 | RNVC: 2

1 May 2014

5975-01-628-4211
Chassis Base

016284211
2710978-2: RNCC: 3 | RNVC: 2

22 May 2014

5975-01-628-2356
Split Conduit Kit

016282356
EZ-300: RNCC: 3 | RNVC: 2

14 May 2014

5975-00-446-6852
Electrical Equipment Mounting Base

004466852
16245-1C: RNCC: 3 | RNVC: 2

1 Jan 1963

5975-01-608-1601
Electrical Equipment Rack

016081601
922354-13: RNCC: 3 | RNVC: 2

20 Jun 2012

5975-01-608-5577
Electrical-Electronic Equipment Chassis

016085577
10497-0220-01: RNCC: 3 | RNVC: 2
10497-0220-01: RNCC: 3 | RNVC: 9

2 Jul 2012

5975-01-607-6427
Electrical Standardized Components Case

016076427
EXP-2041: RNCC: 3 | RNVC: 2

11 Jun 2012

5975-01-610-1677
Electric Cable Joint Box Supplementary Equipment

016101677
GHFC-2-90: RNCC: 3 | RNVC: 2

13 Aug 2012

5975-01-569-0424
Electrical Equipment Mounting Base

015690424
ABP-RM-4B: RNCC: 3 | RNVC: 2

18 Nov 2008

5975-01-570-1287
Strain Electrical Conductor Clamp

015701287
BACC10D622A: RNCC: 3 | RNVC: 2

16 Dec 2008

5975-01-569-7453
Electrical-Electronic Equipment Chassis

015697453
AT-CV1203: RNCC: 3 | RNVC: 2
AT-CV1203: RNCC: 5 | RNVC: 2

8 Dec 2008

5975-01-667-4902
Electrical Equipment Rack Base

016674902
39920-40401-1: RNCC: 3 | RNVC: 2

18 Oct 2017

5975-01-389-6911
Electrical Equipment Rack

013896911
HP12131A: RNCC: 3 | RNVC: 2

28 Apr 1994

5975-01-390-7886
Electrical-Electronic Equipment Chassis

013907886
687-4427-007: RNCC: 3 | RNVC: 2

26 May 1994

5975-01-661-7458
Electrical Equipment Rack

016617458
507750-01-01: RNCC: 3 | RNVC: 9

14 Mar 2017

5975-01-661-7403
Electric Component Rail Guide Stop

016617403
1606-588: RNCC: 3 | RNVC: 2

14 Mar 2017

5975-01-661-3337
Electrical-Electronic Equipment Chassis

016613337
84H342310-003: RNCC: 3 | RNVC: 2

28 Feb 2017

5975-01-662-9113
Cable Hanger

016629113
M22759/16-20-41: RNCC: 3 | RNVC: 2

20 Apr 2017

5975-01-662-8379
Rigid Metal Conduit

016628379
450202-0185: RNCC: 3 | RNVC: 1

20 Apr 2017

5975-01-663-1832
Electrical Tie Down Mounting Base

016631832
MB410C2: RNCC: 3 | RNVC: 2

28 Apr 2017

5975-01-626-2635
Electrical-Electronic Equipment Chassis

016262635
8455803-1: RNCC: 3 | RNVC: 2

4 Mar 2014

5975-01-626-2919
Electrical-Electronic Equipment Panel

016262919
734-65224-1: RNCC: 3 | RNVC: 2
734-65224: RNCC: D | RNVC: 9

5 Mar 2014

5975-01-626-8877
Electrical-Electronic Equipment Chassis

016268877
60081257-000: RNCC: 3 | RNVC: 2
60081257-001: RNCC: 5 | RNVC: 9

24 Mar 2014

5975-01-626-2588
Electrical Equipment Mounting Base

016262588
RMD3000: RNCC: 3 | RNVC: 2

4 Mar 2014

5975-01-565-5075
Electrical Fitting Mounting Base

015655075
5140008-1: RNCC: 3 | RNVC: 2

28 Jul 2008

5975-01-565-5091
Electrical Grounding Plate

015655091
AIR-ACCBRGB=: RNCC: 3 | RNVC: 2

28 Jul 2008

5975-01-107-8028
Electrical-Electronic Equipment Chassis

011078028
881826-1: RNCC: 3 | RNVC: 2

13 Feb 1981

5975-01-109-9603
Bracket

011099603
212A1021: RNCC: 3 | RNVC: 2

25 Mar 1981

5975-01-566-8645
Cable Strain Relief Bushing

015668645
ZT03-04-009-09: RNCC: 3 | RNVC: 2
5PTV4211-109: RNCC: 7 | RNVC: 2

11 Sep 2008

5975-01-387-4861
Electrical Box Connector

013874861
6457320-1: RNCC: 3 | RNVC: 2

5 Mar 1994

5975-01-528-4564
Electronic Junction Rack

015284564
DCR-1A-15-4032: RNCC: 3 | RNVC: 2

14 Mar 2005

5975-01-527-9363
Cable Marker Sleeve

015279363
RPS-8-4/2.0-9: RNCC: 3 | RNVC: 2

24 Feb 2005

5975-01-530-4627
Electrical Equipment Rack

015304627
5HK01501-101: RNCC: 3 | RNVC: 2

27 May 2005

5975-01-660-5412
Electrical Equipment Rack

016605412
ACX288: RNCC: 3 | RNVC: 2

24 Jan 2017

5975-01-661-4366
Interior Cable Rack

016614366
AR8162ABLK: RNCC: 3 | RNVC: 2

2 Mar 2017

5975-01-625-2213
Electrical-Electronic Equipment Panel

016252213
K100532361: RNCC: 3 | RNVC: 2

28 Jan 2014

5975-01-625-4051
Insulator

016254051
68A250225-2017: RNCC: 3 | RNVC: 2

3 Feb 2014

5975-01-563-4191
Electrical Bushing

015634191
RW309-5: RNCC: 3 | RNVC: 2

10 May 2008

5975-01-563-4074
Electrical Bushing

015634074
RQ701-1: RNCC: 3 | RNVC: 2

10 May 2008

5975-01-565-9855
Electrical Equipment Rack

015659855
SUN-RACK 900-38: RNCC: 3 | RNVC: 2

14 Aug 2008

5975-01-385-6437
Electrical Equipment Cabinet

013856437
M042A029-04: RNCC: 3 | RNVC: 2

15 Jan 1994

5975-01-385-6301
Electrical-Electronic Equipment Panel

013856301
9037D80-1: RNCC: 3 | RNVC: 2
9037D80-1: RNCC: 5 | RNVC: 9

14 Jan 1994

5975-01-384-1999
Electrical-Electronic Equipment Panel

013841999
9281882: RNCC: 3 | RNVC: 2

9 Dec 1993

5975-01-527-0248
Electrical-Electronic Equipment Chassis

015270248
DE100I-CSW160: RNCC: 3 | RNVC: 9

14 Jan 2005

5975-01-658-0628
Junction Box

016580628
1590WDE: RNCC: 3 | RNVC: 2

12 Sep 2016

5975-01-658-9625
Electrical Equipment Rack

016589625
279410-07: RNCC: 3 | RNVC: 2

27 Oct 2016

5975-01-622-6328
Electrical Equipment Mounting Base

016226328
719-5070-002: RNCC: 3 | RNVC: 2

16 Oct 2013

5975-01-559-4531
Electrical Equipment Rack

015594531
SCC EIC RACK: RNCC: 3 | RNVC: 2

18 Dec 2007

5975-01-563-1539
Electrical-Electronic Equipment Chassis

015631539
VS-C6504E-S720-10G: RNCC: 3 | RNVC: 2

2 May 2008

5975-01-563-4073
Electrical Bushing

015634073
RL82-5: RNCC: 3 | RNVC: 2

10 May 2008

5975-01-108-6101
Elbow

011086101
12CW-2077-3: RNCC: 3 | RNVC: 2

2 Mar 1981

5975-01-383-1446
Radio Frequency Cable Splicing Kit

013831446
80-6100-6386-1: RNCC: 3 | RNVC: 9
80-6100-6386-1: RNCC: 5 | RNVC: 9

19 Nov 1993

5975-01-383-7008
Electrical-Electronic Equipment Chassis

013837008
462948: RNCC: 3 | RNVC: 2

1 Dec 1993

5975-01-642-3714
Flexible Metal Conduit Assembly

016423714
287N6102-39: RNCC: 3 | RNVC: 2

24 Feb 2015

5975-01-594-1061
Spec Grommet

015941061
2604385C1: RNCC: 3 | RNVC: 2

22 Apr 2011

5975-01-647-1457
Cable Reinforcing Link

016471457
69-73855-1: RNCC: 3 | RNVC: 2

13 Aug 2015

5975-01-646-6808
Electrical Equipment Rack

016466808
ST34ESA: RNCC: 3 | RNVC: 9

28 Jul 2015

5975-01-558-6984
Electrical Cable Nipple

015586984
19812-827.01: RNCC: 3 | RNVC: 2
96003286: RNCC: 5 | RNVC: 2

19 Nov 2007

5975-01-558-8320
Electrical-Electronic Equipment Panel

015588320
2218026-003: RNCC: 3 | RNVC: 2

26 Nov 2007

5975-01-558-7011
Electronic Equipment Mounting Tray

015587011
Y1130A: RNCC: 3 | RNVC: 2
Y1130A: RNCC: 3 | RNVC: 9

19 Nov 2007

5975-01-560-8217
Electrical-Electronic Equipment Chassis

015608217
11-1006252-43: RNCC: 3 | RNVC: 2

13 Feb 2008

5975-01-561-4342
Electrical-Electronic Equipment Chassis

015614342
885560T03: RNCC: 3 | RNVC: 2
885560T01: RNCC: 5 | RNVC: 2
885560T01: RNCC: 5 | RNVC: 9

5 Mar 2008

5975-01-561-7470
Electronic Equipment Mounting Tray

015617470
MT4-4201: RNCC: 3 | RNVC: 2

17 Mar 2008

5975-01-561-9805
Splice Box Assy

015619805
237206-0008: RNCC: 3 | RNVC: 2

25 Mar 2008

5975-01-390-7890
Electrical-Electronic Equipment Panel

013907890
687-4433-003: RNCC: 3 | RNVC: 2

26 May 1994

5975-01-379-2287
Electrical Wall Plate

013792287
207964-100: RNCC: 3 | RNVC: 2
207964-100: RNCC: 5 | RNVC: 9
5975013792287: RNCC: 8 | RNVC: 1
207964-100: RNCC: 8 | RNVC: 2

29 Aug 1993

5975-01-381-0738
Electrical-Electronic Equipment Chassis

013810738
13027284: RNCC: 3 | RNVC: 2

7 Oct 1993

5975-01-476-8899
Electrical Standardized Components Case Section

014768899
10522-4575-01: RNCC: 3 | RNVC: 2

25 Jul 2000

5975-01-476-8852
Cable Marker Sleeve

014768852
013-007382-061: RNCC: 3 | RNVC: 2

25 Jul 2000

5975-01-476-8101
Electrical Equipment Mounting Base

014768101
497070-10: RNCC: 3 | RNVC: 2

24 Jul 2000

5975-01-476-8721
Electrical Cable Support

014768721
10522-4510-01: RNCC: 3 | RNVC: 2

25 Jul 2000

5975-01-477-2033
Electrical-Electronic Equipment Chassis

014772033
5090HLF15EC-101: RNCC: 3 | RNVC: 2
72B245024-101: RNCC: 7 | RNVC: 2

2 Aug 2000

5975-01-655-2323
Electrical-Electronic Equipment Panel

016552323
25-8NF2101-15: RNCC: 3 | RNVC: 2
25-8NF2101-15: RNCC: 3 | RNVC: 9

23 May 2016

5975-01-645-8800
Electrical Equipment Rack

016458800
ACXMOHDEAR6-FPAC: RNCC: 3 | RNVC: 9

2 Jul 2015

5975-01-645-3453
Cable Hanger

016453453
01.102.002.1: RNCC: 3 | RNVC: 2

12 Jun 2015

5975-01-645-8794
Electrical Equipment Rack

016458794
ACXMODH6FPAC-R2: RNCC: 3 | RNVC: 2
ACXMODH6FPAC-R2: RNCC: 5 | RNVC: 2
ACXMODH6FPAC-R2: RNCC: 5 | RNVC: 2

2 Jul 2015

5975-00-332-9385
Electrical Equipment Mounting Base

003329385
608-6937-001: RNCC: 3 | RNVC: 2

16 Dec 1973

5975-01-492-8328
Cable Hanger

014928328
269A8618: RNCC: 3 | RNVC: 2
269A8618: RNCC: 3 | RNVC: 9

13 Dec 2001

5975-01-492-5357
Electrical Equipment Rack

014925357
6237101-100: RNCC: 3 | RNVC: 2

3 Dec 2001

5975-01-170-1282
Electrical Equipment Cabinet

011701282
H9642DC: RNCC: 3 | RNVC: 2

20 Jan 1984

5975-01-475-7281
Flexible Metal Conduit Assembly

014757281
226494-DL0000: RNCC: 3 | RNVC: 2
17B2E2000-529: RNCC: 7 | RNVC: 2

12 Jun 2000

5975-01-616-5441
Electrical-Electronic Equipment Chassis

016165441
04-823401-20: RNCC: 3 | RNVC: 2

19 Feb 2013

5975-01-616-3673
Flexible Metal Conduit Assembly

016163673
ACP8000-598: RNCC: 3 | RNVC: 2

12 Feb 2013

5975-01-617-3117
Electrical Tie Down Mounting Base

016173117
NMCSB80000UGM510: RNCC: 3 | RNVC: 2

19 Mar 2013

5975-01-616-1454
Electrical Conduit Adapter

016161454
59268: RNCC: 3 | RNVC: 2
59268: RNCC: 3 | RNVC: 2
SMU-00000163: RNCC: 5 | RNVC: 2
59268: RNCC: 5 | RNVC: 2
59268: RNCC: 5 | RNVC: 9

4 Feb 2013

5975-01-661-3408
Insulator Bracket

016613408
231-7070: RNCC: 3 | RNVC: 2

28 Feb 2017

5975-01-661-9299
Electrical Equipment Mounting Base

016619299
822-2346-001: RNCC: 3 | RNVC: 2

21 Mar 2017

5975-01-661-7694
Electrical Components Tie Down Strap

016617694
8121: RNCC: 3 | RNVC: 2

15 Mar 2017

5975-01-662-7941
Metallic Raceway

016627941
AR8173BLK: RNCC: 3 | RNVC: 2

20 Apr 2017

5975-01-664-4734
Electrical-Electronic Equipment Chassis

016644734
K2R81A: RNCC: 3 | RNVC: 2

21 Jun 2017

5975-01-667-9448
Electrical Equipment Mounting Base

016679448
400484-01: RNCC: 3 | RNVC: 2

6 Nov 2017

5975-01-669-2061
Electrical Equipment Rack

016692061
011-02422-00: RNCC: 3 | RNVC: 2

28 Dec 2017

5975-01-669-2684
Electrical Box Divider

016692684
MS12-PMS38999-1275/3.3-NF: RNCC: 3 | RNVC: 2
60220281-00: RNCC: 5 | RNVC: 2

3 Jan 2018

5975-01-554-9237
Stuffing Tube

015549237
302-5911509PC6-39A-2: RNCC: 3 | RNVC: 1
AII-MTS-06-250APPNDXAITEM19: RNCC: 5 | RNVC: 1

23 Aug 2007

5975-01-179-6749
Switch Cover

011796749
3322771: RNCC: 3 | RNVC: 2
3322771: RNCC: 5 | RNVC: 9

20 May 1984

5975-01-169-6630
Electrical Components Tie Down Strap

011696630
10S300-2-221: RNCC: 3 | RNVC: 9
10S300-2-221: RNCC: C | RNVC: 1

12 Jan 1984

5975-01-490-4893
Electrical Equipment Rack

014904893
7014-T00: RNCC: 3 | RNVC: 2
7014-T00-5: RNCC: 5 | RNVC: 2

28 Sep 2001

5975-01-490-1453
Electrical Equipment Rack

014901453
5HK01501-107: RNCC: 3 | RNVC: 2

20 Sep 2001

5975-01-386-7031
Electrical-Electronic Equipment Chassis

013867031
7547200-2: RNCC: 3 | RNVC: 2

11 Feb 1994

5975-01-473-0071
Electrical-Electronic Equipment Chassis

014730071
346134-1: RNCC: 3 | RNVC: 2

23 Mar 2000

5975-01-614-7179
Electrical-Electronic Equipment Chassis

016147179
K10048685-502: RNCC: 3 | RNVC: 2

13 Dec 2012

5975-01-615-0217
Electrical-Electronic Equipment Panel

016150217
195D5432P1: RNCC: 3 | RNVC: 2

21 Dec 2012

5975-01-615-0221
Electrical-Electronic Equipment Panel

016150221
195D5459: RNCC: 3 | RNVC: 2

21 Dec 2012

5975-01-615-7105
Junction Box

016157105
2009-41A3000-3: RNCC: 3 | RNVC: 2

22 Jan 2013

5975-01-615-7838
Electrical Equipment Mounting Base

016157838
SFR514: RNCC: 3 | RNVC: 2

23 Jan 2013

5975-01-615-7080
Electrical-Electronic Equipment Chassis

016157080
16036-001: RNCC: 3 | RNVC: 2

22 Jan 2013

5975-01-677-4997
Electric Cable Joint Box Supplementary Equipment

016774997
N6709C: RNCC: 3 | RNVC: 2
N6709C: RNCC: 3 | RNVC: 9
0X00147920: RNCC: 5 | RNVC: 2

17 Dec 2018

5975-01-675-2753
Electrical Equipment Mounting Base

016752753
200-100716-101: RNCC: 3 | RNVC: 2

30 Aug 2018

5975-01-674-6797
Cable Hanger

016746797
CMS151039: RNCC: 3 | RNVC: 2

7 Aug 2018

5975-01-679-6031
Junction Box Assembly

016796031
145E3118-7: RNCC: 3 | RNVC: 2

1 Apr 2019

5975-01-681-8850
Flexible Metal Conduit

016818850
231-9897: RNCC: 3 | RNVC: 2

11 Jul 2019

5975-00-441-2085
Cable Clamp

004412085
9006688: RNCC: 3 | RNVC: 9

1 Jan 1963

5975-01-552-3174
Electrical Equipment Mounting Base

015523174
719-0050-001: RNCC: 3 | RNVC: 2

11 Jun 2007

5975-01-181-9609
Junction Box

011819609
E987R: RNCC: 3 | RNVC: 9
00034481066866: RNCC: 5 | RNVC: 9

18 Jun 1984

5975-01-488-4122
Cable Marker Sleeve

014884122
G21231: RNCC: 3 | RNVC: 2
G95948: RNCC: D | RNVC: 9

23 Aug 2001

5975-01-488-5656
Cable Marker Sleeve

014885656
G21234: RNCC: 3 | RNVC: 2
G95996: RNCC: D | RNVC: 9

28 Aug 2001

5975-01-487-5502
Electrical Conduit Nipple

014875502
1313-07-0001: RNCC: 3 | RNVC: 2
G95953: RNCC: D | RNVC: 9

9 Aug 2001

5975-01-487-8358
Electrical-Electronic Equipment Chassis

014878358
659-6256-002: RNCC: 3 | RNVC: 2

20 Aug 2001

5975-01-471-3397
Electrical Equipment Cabinet

014713397
14CD: RNCC: 3 | RNVC: 2

31 Jan 2000

5975-01-471-5921
Electrical Equipment Mounting Base

014715921
7-511A21641-16: RNCC: 3 | RNVC: 2
7-511A21641-16: RNCC: 5 | RNVC: 2
7-511A21641-16: RNCC: 5 | RNVC: 9

7 Feb 2000

5975-01-612-6812
Electrical Equipment Rack

016126812
17P1E1590-509: RNCC: 3 | RNVC: 2

17 Oct 2012

5975-01-612-4808
Junction Box

016124808
IM-DEEP-3000-006: RNCC: 3 | RNVC: 2

12 Oct 2012

5975-01-613-7804
Electrical Equipment Mounting Base

016137804
FPM-5750-P: RNCC: 3 | RNVC: 2

16 Nov 2012

5975-01-523-0425
Electrical Equipment Foot

015230425
RM1005A01: RNCC: 3 | RNVC: 2
RM1005A01: RNCC: 3 | RNVC: 9

18 Aug 2004

5975-01-671-2255
Electrical-Electronic Equipment Chassis

016712255
11569642: RNCC: 3 | RNVC: 2

20 Mar 2018

5975-01-486-6319
Electrical Equipment Mounting Base

014866319
ETN9795: RNCC: 3 | RNVC: 2

9 Jul 2001

5975-01-486-9605
Electrical-Electronic Equipment Chassis

014869605
7-511C10013-9: RNCC: 3 | RNVC: 2

19 Jul 2001

5975-01-486-7194
Blank Panel

014867194
10922483: RNCC: 3 | RNVC: 2

12 Jul 2001

5975-01-163-5437
Stand-Off Bushing

011635437
130-20-AL-6/32P: RNCC: 3 | RNVC: 2

5 Oct 1983

5975-01-411-1915
Electrical Equipment Shelf

014111915
08903-00024: RNCC: 3 | RNVC: 2
08903-00024: RNCC: 3 | RNVC: 9
08903-00024: RNCC: 5 | RNVC: 9

20 Mar 1995

5975-01-408-8319
Electrical Equipment Foot

014088319
01650-47701: RNCC: 3 | RNVC: 2
01650-47701: RNCC: 3 | RNVC: 9
01650-47701: RNCC: 5 | RNVC: 9
01650-47701: RNCC: 5 | RNVC: 9

27 Feb 1995

5975-01-468-8541
Flexible Metal Conduit Assembly

014688541
3260AS393: RNCC: 3 | RNVC: 2

25 Oct 1999

5975-01-468-9244
Flexible Metal Conduit Assembly

014689244
254122: RNCC: 3 | RNVC: 2

27 Oct 1999

5975-01-469-7052
Electrical Bonding Ring

014697052
A1369-5: RNCC: 3 | RNVC: 2
A1369-5: RNCC: 3 | RNVC: 9

19 Nov 1999

5975-01-470-2998
Flexible Metal Conduit Assembly

014702998
230745-DL0000: RNCC: 3 | RNVC: 2
17B2E2000-567: RNCC: 7 | RNVC: 2

14 Dec 1999

5975-01-468-9241
Flexible Metal Conduit Assembly

014689241
254731: RNCC: 3 | RNVC: 2

27 Oct 1999

5975-01-550-3219
Electrical-Electronic Equipment Chassis

015503219
R548730-01: RNCC: 3 | RNVC: 2

16 Apr 2007

5975-01-485-8792
Cable Marker Sleeve

014858792
651670: RNCC: 3 | RNVC: 2

11 Jun 2001

5975-01-485-8796
Cable Marker Sleeve

014858796
651699: RNCC: 3 | RNVC: 2

11 Jun 2001

5975-01-468-4310
Electrical-Electronic Equipment Chassis

014684310
DE200I-CSW: RNCC: 3 | RNVC: 9

8 Oct 1999

5975-01-657-7686
Mounting Plate

016577686
39278-40123-3: RNCC: 3 | RNVC: 2

29 Aug 2016

5975-01-658-6562
Cable Strain Relief Bushing

016586562
737893-2: RNCC: 3 | RNVC: 2

11 Oct 2016

5975-01-563-5406
Electrical Wall Plate

015635406
BS 10100: RNCC: 3 | RNVC: 9

13 May 2008

5975-01-549-0725
Rigid Metal Conduit

015490725
5HM40133-121: RNCC: 3 | RNVC: 2

9 Mar 2007

5975-01-548-8100
Junction Box Cover

015488100
5493068: RNCC: 3 | RNVC: 2

5 Mar 2007

5975-01-549-2149
Electrical-Electronic Equipment Chassis

015492149
12R2-02BR20FFFCRX: RNCC: 3 | RNVC: 2

14 Mar 2007

5975-01-171-0515
Electrical Equipment Mounting Base

011710515
622-5148-001: RNCC: 3 | RNVC: 2

3 Feb 1984

5975-01-483-8724
Electrical Conduit Adapter

014838724
712GS116A1932C5: RNCC: 3 | RNVC: 2

10 Apr 2001

5975-01-484-6968
Strap Cap Assembly

014846968
10178-1510: RNCC: 3 | RNVC: 2

4 May 2001

5975-01-484-7017
Electrical Components Tie Down Strap

014847017
ST1306BA-75-225-SB: RNCC: 3 | RNVC: 2
2402A75-225SH: RNCC: 7 | RNVC: 2

4 May 2001

5975-01-484-5003
Cable Marker Sleeve

014845003
2540806-99: RNCC: 3 | RNVC: 2
2540806-99: RNCC: 5 | RNVC: 9

30 Apr 2001

5975-01-467-0565
Cable Marker Sleeve

014670565
TMS-SCE-1/8-2.0-S1-4: RNCC: 3 | RNVC: 2
FV 2224914/4: RNCC: 5 | RNVC: 2
TMS-SCE-1/8-2.0-S1-4: RNCC: 5 | RNVC: 2
FV 2224914 ITEM 4: RNCC: 5 | RNVC: 2
ECS6036CN4: RNCC: 5 | RNVC: 2
TMS-SCE-1/8-2.0-S1-4: RNCC: 5 | RNVC: 2

11 Aug 1999

5975-01-467-7042
Electrical Equipment Rack

014677042
J1464A: RNCC: 3 | RNVC: 2

10 Sep 1999

5975-01-609-1456
Junction Box

016091456
A14N126: RNCC: 3 | RNVC: 2
007496: RNCC: 5 | RNVC: 2

18 Jul 2012

5975-01-651-3161
Electrical Equipment Shelf

016513161
7-511115247-003: RNCC: 3 | RNVC: 2

13 Jan 2016

5975-01-654-3129
Electrical Components Tie Down Strap

016543129
10710: RNCC: 3 | RNVC: 2

25 Apr 2016

5975-01-652-1201
Electrical Equipment Cabinet

016521201
11840-724: RNCC: 3 | RNVC: 2

10 Feb 2016

5975-01-655-5928
Electrical Grounding Plate

016555928
09864: RNCC: 3 | RNVC: 2
220-9978: RNCC: 5 | RNVC: 9

2 Jun 2016

5975-01-656-4133
Blank Panel

016564133
71450-21109-107: RNCC: 3 | RNVC: 2

30 Jun 2016

5975-01-547-3216
Electronic Chassis

015473216
R467083-01: RNCC: 3 | RNVC: 2

17 Jan 2007

5975-01-169-2658
Electrical-Electronic Equipment Chassis

011692658
0N313315-1: RNCC: 3 | RNVC: 2

5 Jan 1984

5975-01-610-6706
Electrical Equipment Rack

016106706
3224-0010-0: RNCC: 3 | RNVC: 2

24 Aug 2012

5975-01-483-6239
Electrical Equipment Rack Base

014836239
123SCAV5633-15: RNCC: 1 | RNVC: 2
20E1232-3: RNCC: 3 | RNVC: 2
123SCAV5633-15: RNCC: 5 | RNVC: 9

4 Apr 2001

5975-01-483-9903
Cable Marker Sleeve

014839903
2540806-53: RNCC: 3 | RNVC: 2

13 Apr 2001

5975-01-482-9377
Electrical Equipment Cabinet

014829377
641-4064-001: RNCC: 3 | RNVC: 2

9 Mar 2001

5975-01-606-8431
Electrical Standardized Components Case

016068431
570350G1: RNCC: 3 | RNVC: 2

24 May 2012

5975-01-608-5603
Electrical-Electronic Equipment Chassis

016085603
SUN BLADE 6000 A90-D: RNCC: 3 | RNVC: 2

2 Jul 2012

5975-01-606-9052
Electrical Equipment Rack

016069052
2594457: RNCC: 3 | RNVC: 2

25 May 2012

5975-01-607-2068
Md Rr Trnst Svr Bl

016072068
09205025-01: RNCC: 3 | RNVC: 1

5 Jun 2012

5975-01-650-2518
Mounting Plate

016502518
68R870329-1001: RNCC: 3 | RNVC: 2

24 Nov 2015

5975-00-322-6274
Junction

003226274
37-2-5403: RNCC: 3 | RNVC: 2

1 Jan 1963

5975-01-544-2393
Cable Hanger

015442393
211784: RNCC: 3 | RNVC: 2

5 Oct 2006

5975-01-117-6468
Electrical Components Tie Down Strap

011176468
PLT4H-C: RNCC: 3 | RNVC: 2
RT 1400: RNCC: 3 | RNVC: 2
RT-1400-9: RNCC: 5 | RNVC: 9

19 Aug 1981

5975-01-608-9628
Metallic Raceway Assembly

016089628
0726016-7: RNCC: 3 | RNVC: 2
0726016-7: RNCC: 3 | RNVC: 9

13 Jul 2012

5975-01-608-9716
Electrical Components Tie Down Strap

016089716
0412007-8: RNCC: 3 | RNVC: 2
0412007-8: RNCC: 3 | RNVC: 9

13 Jul 2012

5975-01-610-1703
Electric Cable Joint Box Supplementary Equipment

016101703
GHFC-3-90: RNCC: 3 | RNVC: 2

13 Aug 2012

5975-01-608-5921
Electrical Equipment Mounting Base

016085921
RF-7800I-VM301: RNCC: 3 | RNVC: 2

3 Jul 2012

5975-01-608-6134
Metallic Raceway Assembly

016086134
211-0573: RNCC: 3 | RNVC: 2
211-0573: RNCC: 5 | RNVC: 2
CV131923: RNCC: 5 | RNVC: 2

5 Jul 2012

5975-01-346-6079
Electrical Equipment Mounting Base

013466079
622-3961-001: RNCC: 3 | RNVC: 2
673821-101: RNCC: 5 | RNVC: 9

9 Oct 1991

5975-01-347-0481
Electrical Components Tie Down Strap

013470481
PLT1-5MC10: RNCC: 3 | RNVC: 2

13 Oct 1991

5975-01-463-6371
Electrical Equipment Mounting Base

014636371
4257: RNCC: 3 | RNVC: 2

30 Mar 1999

5975-01-652-8159
Electrical Conduit Tee

016528159
TF5IW-E: RNCC: 3 | RNVC: 2

4 Mar 2016

5975-01-653-3741
Electrical Equipment Cabinet

016533741
9900-2000: RNCC: 3 | RNVC: 2

22 Mar 2016

5975-01-642-1489
Cable Hanger

016421489
CLAMP-060: RNCC: 3 | RNVC: 2

13 Feb 2015

5975-01-641-9972
Electrical-Electronic Equipment Chassis

016419972
12102 4IF: RNCC: 3 | RNVC: 2

10 Feb 2015

5975-01-642-1461
Electrical Equipment Mounting Base

016421461
ACCAA-752-76597-00: RNCC: 3 | RNVC: 2
68246: RNCC: 5 | RNVC: 2

13 Feb 2015

5975-01-641-9687
Junction Box Cover

016419687
115-00500-02: RNCC: 3 | RNVC: 2

9 Feb 2015

5975-00-347-9710
Electrical Conductor Bushing

003479710
94A71: RNCC: 3 | RNVC: 2

1 Jan 1961

5975-00-348-4474
Electrical-Electronic Equipment Chassis

003484474
616R999G01: RNCC: 3 | RNVC: 2

24 Jan 1974

5975-01-542-5114
Electrical Equipment Mounting Base

015425114
101-10613-00: RNCC: 3 | RNVC: 2

8 Aug 2006

5975-01-544-2370
Electrical Box Connector

015442370
211814: RNCC: 3 | RNVC: 2

5 Oct 2006

5975-01-607-6125
Flexible Nonmetallic Conduit

016076125
514-1905-001: RNCC: 3 | RNVC: 9

8 Jun 2012

5975-01-607-5787
Metallic Raceway Assembly

016075787
1234614-1: RNCC: 3 | RNVC: 2
1234614-1: RNCC: 3 | RNVC: 9

8 Jun 2012

5975-01-608-1471
Electrical-Electronic Equipment Panel

016081471
7-W11660052-1: RNCC: 3 | RNVC: 2

20 Jun 2012

5975-01-335-6552
Blank Panel

013356552
86421043-1: RNCC: 3 | RNVC: 2

12 Mar 1991

5975-01-336-5113
Helicopter Support Heatsink

013365113
4-055019-03: RNCC: 3 | RNVC: 2

27 Mar 1991

5975-01-340-2667
Electrical Components Tie Down Strap

013402667
506657-4: RNCC: 3 | RNVC: 2

11 Jun 1991

5975-01-340-1386
Cable Marker Sleeve

013401386
506658-8: RNCC: 3 | RNVC: 2

10 Jun 1991

5975-01-522-7120
Electrical Conductor Bushing

015227120
1560-1: RNCC: 3 | RNVC: 2

9 Aug 2004

5975-01-522-1074
Electrical-Electronic Equipment Chassis

015221074
DE100I-RA100/B: RNCC: 3 | RNVC: 9

19 Jul 2004

5975-01-523-1176
Electronic Equipment Mounting Tray

015231176
468569-01: RNCC: 3 | RNVC: 2

20 Aug 2004

5975-01-462-0700
Electrical-Electronic Equipment Chassis

014620700
SR001A: RNCC: 3 | RNVC: 9

20 Jan 1999

5975-01-651-3403
Electrical Equipment Shelf

016513403
7-511115048-001: RNCC: 3 | RNVC: 2

14 Jan 2016

5975-01-651-7090
End Plate Kit

016517090
8003542: RNCC: 3 | RNVC: 2

27 Jan 2016

5975-01-640-8409
Electrical Equipment Shelf

016408409
164111-01: RNCC: 3 | RNVC: 2
164111-01: RNCC: 3 | RNVC: 9

29 Dec 2014

5975-00-397-9533
Electrical Equipment Mounting Base

003979533
3179809-1: RNCC: 3 | RNVC: 2
3179809-1: RNCC: 3 | RNVC: 9

12 Apr 1974

5975-00-395-7051
Ne Harness Assembly

003957051
F147-62: RNCC: 3 | RNVC: 9
F147-62: RNCC: C | RNVC: 1

1 Jan 1963

5975-01-540-0040
Electrical Equipment Mounting Base

015400040
257A655-2: RNCC: 3 | RNVC: 2

5 May 2006

5975-01-110-5078
Magnetic Starter

011105078
GCR1DC0J: RNCC: 3 | RNVC: 9

2 Apr 1981

5975-01-110-0811
Conduit Assy

011100811
1310-0001-4: RNCC: 3 | RNVC: 2
1310-0001-4: RNCC: 3 | RNVC: 9

26 Mar 1981

5975-01-604-6155
Electrical Equipment Rack

016046155
011-01011-00: RNCC: 3 | RNVC: 2

10 Apr 2012

5975-01-604-6681
Electrical Equipment Rack

016046681
11-1013803: RNCC: 3 | RNVC: 2

11 Apr 2012

5975-01-605-8831
Electrical-Electronic Equipment Chassis

016058831
817R579G03: RNCC: 3 | RNVC: 2

28 Apr 2012

5975-01-606-2142
Electrical-Electronic Equipment Chassis

016062142
M311360: RNCC: 3 | RNVC: 2

11 May 2012

5975-01-420-9539
Electrical Equipment Rack

014209539
7334095G1: RNCC: 3 | RNVC: 2

28 Oct 1995

5975-01-419-3751
Electrical-Electronic Equipment Chassis

014193751
1064AS2505: RNCC: 3 | RNVC: 2
1064AS2505: RNCC: 5 | RNVC: 2

21 Sep 1995

5975-01-520-5020
Electrical-Electronic Equipment Chassis

015205020
8205704G1: RNCC: 3 | RNVC: 2
8205633G2: RNCC: 5 | RNVC: 9

13 May 2004

5975-01-521-0576
Electrical-Electronic Equipment Panel

015210576
622-6830-001: RNCC: 3 | RNVC: 2

8 Jun 2004

5975-01-648-7673
Electronic Equipment Mounting Tray

016487673
284W1693-2: RNCC: 3 | RNVC: 2

6 Oct 2015

5975-01-648-7376
Electrical Equipment Shelf

016487376
284A3730-101: RNCC: 3 | RNVC: 2

5 Oct 2015

5975-01-650-4648
Junction Box

016504648
PX-2: RNCC: 3 | RNVC: 2

4 Dec 2015

5975-01-570-1293
Strain Electrical Conductor Clamp

015701293
BACC10DW17D: RNCC: 3 | RNVC: 2

16 Dec 2008

5975-00-394-2537
Ignition Cab Marker

003942537
AN4028-5: RNCC: 2 | RNVC: 2

1 Jan 1963

5975-01-538-7255
Elec Condui Adapter

015387255
HF1205120: RNCC: 3 | RNVC: 2

29 Mar 2006

5975-01-539-1640
Electrical-Electronic Equipment Chassis

015391640
FS-2570T: RNCC: 3 | RNVC: 2

12 Apr 2006

5975-01-539-0003
Electrical-Electronic Equipment Panel

015390003
S46998-Z104-A70: RNCC: 3 | RNVC: 9

6 Apr 2006

5975-01-418-1631
Cable Marker Sleeve

014181631
17P1E1414-7: RNCC: 3 | RNVC: 2

21 Aug 1995

5975-01-418-6036
Terminal Board

014186036
9D0090-43U: RNCC: 3 | RNVC: 2
RC11090-43U: RNCC: 5 | RNVC: 2

31 Aug 1995

5975-01-518-5112
Electronic Equipment Mounting Tray

015185112
D9G87-00182: RNCC: 3 | RNVC: 2

15 Mar 2004

5975-01-518-5566
Electrical-Electronic Equipment Chassis

015185566
FS-8915-LMC-HM: RNCC: 3 | RNVC: 2
5102080-3: RNCC: 5 | RNVC: 2

16 Mar 2004

5975-01-519-0444
Electrical Conduit Coupling

015190444
H316A001-101: RNCC: 3 | RNVC: 2

2 Apr 2004

5975-01-647-0776
Junction Box Assembly

016470776
G-101-7562: RNCC: 3 | RNVC: 2

11 Aug 2015

5975-01-647-8346
Electrical Equipment Mounting Base

016478346
33-349-200: RNCC: 3 | RNVC: 2

3 Sep 2015

5975-01-648-7221
Junction Box Assembly

016487221
2841B1848-102: RNCC: 3 | RNVC: 2

5 Oct 2015

5975-01-561-3235
Electrical Equipment Mounting Base

015613235
010-10306-00: RNCC: 3 | RNVC: 2

29 Feb 2008

5975-01-562-1773
Electronic Equipment Mounting Tray

015621773
92900-01812-102: RNCC: 3 | RNVC: 2

1 Apr 2008

5975-01-562-2180
Electrical-Electronic Equipment Chassis

015622180
541-0645: RNCC: 3 | RNVC: 2

2 Apr 2008

5975-00-350-9286
Flexible Nonmetallic Conduit

003509286
7390198: RNCC: 3 | RNVC: 2

12 Aug 1968

5975-01-534-8383
Electrical Grounding Plate

015348383
152941-1: RNCC: 3 | RNVC: 2

3 Nov 2005

5975-01-535-9255
Flexible Metal Conduit

015359255
227642-DL0000: RNCC: 3 | RNVC: 2

14 Dec 2005

5975-01-536-6076
Flexible Metal Conduit Assembly

015366076
227704-DL0000: RNCC: 3 | RNVC: 2

9 Jan 2006

5975-01-536-7611
Flexible Metal Conduit

015367611
230731-DL0000: RNCC: 3 | RNVC: 2

12 Jan 2006

5975-01-536-2330
Flexible Metal Conduit Assembly

015362330
227758-DL0000: RNCC: 3 | RNVC: 2

22 Dec 2005

5975-01-536-8467
Electrical-Electronic Equipment Chassis

015368467
IPC-602P4-30Z: RNCC: 3 | RNVC: 2

18 Jan 2006

5975-01-537-2455
Electrical Equipment Rack

015372455
170-077-036: RNCC: 3 | RNVC: 2

31 Jan 2006

5975-01-537-2100
Electrical-Electronic Equipment Chassis

015372100
C7206VXR/400/2FE: RNCC: 3 | RNVC: 2

30 Jan 2006

5975-01-682-7086
Electrical Components Tie Down Strap

016827086
304-7080: RNCC: 3 | RNVC: 2

20 Aug 2019

5975-01-693-3459
Blank Panel

016933459
EZF6N04A: RNCC: 3 | RNVC: 2
324K426: RNCC: D | RNVC: 9

5 Feb 2021

5975-01-694-0324
Electrical Wall Plate

016940324
152116-15: RNCC: 3 | RNVC: 2
152116-15: RNCC: 5 | RNVC: 2

15 Mar 2021

5975-01-696-4244
Electrical Equipment Rack

016964244
16E5448-3: RNCC: 3 | RNVC: 2
16E5448-3: RNCC: 5 | RNVC: 2

27 Jul 2021

5975-01-696-0061
Electrical Equipment Shelf

016960061
A5275131-1: RNCC: 3 | RNVC: 2

2 Jul 2021

5975-01-696-1753
Electrical Equipment Cabinet

016961753
E3MCBC10B: RNCC: 3 | RNVC: 2
L-46B-6-CB-C: RNCC: 5 | RNVC: 2

14 Jul 2021

5975-01-695-8265
Electrical Conduit Union

016958265
STR150B: RNCC: 3 | RNVC: 2

24 Jun 2021

5975-01-697-0941
Electrical-Electronic Equipment Panel

016970941
AD-2331646-101: RNCC: 3 | RNVC: 2

1 Sep 2021

5975-01-696-8878
Electrical Equipment Mounting Base

016968878
3367187-3: RNCC: 3 | RNVC: 2

23 Aug 2021

5975-01-413-6668
Blank Panel

014136668
5062-5595: RNCC: 3 | RNVC: 2

18 May 1995

5975-01-695-7717
Electrical Equipment Mounting Base

016957717
405955-01: RNCC: 3 | RNVC: 2

23 Jun 2021

5975-01-516-6214
Electronic Equipment Mounting Tray

015166214
97P2304: RNCC: 3 | RNVC: 2

13 Jan 2004

5975-01-518-0587
Electrical Wall Plate

015180587
81-1771-1: RNCC: 3 | RNVC: 2

1 Mar 2004

5975-01-644-0596
Electrical Equipment Rack

016440596
93614EX: RNCC: 3 | RNVC: 2

21 Apr 2015

5975-01-644-4780
Electrical-Electronic Equipment Chassis

016444780
CH-14404: RNCC: 3 | RNVC: 2

7 May 2015

5975-01-645-8803
Blank Panel

016458803
ACXMODH21-4S: RNCC: 3 | RNVC: 2
10407235: RNCC: 6 | RNVC: 9

2 Jul 2015

5975-01-559-8038
Electrical Equipment Rack

015598038
X8100A-4: RNCC: 3 | RNVC: 2
370-6691: RNCC: 5 | RNVC: 2
X3100A-4: RNCC: 5 | RNVC: 9

7 Jan 2008

5975-01-649-8168
Electrical Tie Down Mounting Base

016498168
CB4560V5: RNCC: 3 | RNVC: 2

12 Nov 2015

5975-01-535-9240
Flexible Metal Conduit

015359240
227651-DL0000: RNCC: 3 | RNVC: 2

14 Dec 2005

5975-01-536-2600
Electrical Equipment Rack

015362600
5NK01201-103: RNCC: 3 | RNVC: 2

23 Dec 2005

5975-01-534-8521
Electronic Equipment Mounting Tray

015348521
DRW150SCSIBK: RNCC: 3 | RNVC: 2

3 Nov 2005

5975-01-534-9934
Electrical Components Tie Down Strap

015349934
12700029: RNCC: 3 | RNVC: 2

9 Nov 2005

5975-01-535-9959
Flexible Metal Conduit Assembly

015359959
227694-DL0000: RNCC: 3 | RNVC: 2

15 Dec 2005

5975-01-536-2196
Electrical Equipment Rack

015362196
65000124: RNCC: 3 | RNVC: 2

22 Dec 2005

5975-01-534-7111
Electrical Equipment Drawer

015347111
11456764: RNCC: 3 | RNVC: 2

31 Oct 2005

5975-01-146-4012
Interconnecting Box

011464012
C5072943: RNCC: 3 | RNVC: 2
J-3792/VRC: RNCC: 5 | RNVC: 2
C5072943: RNCC: 5 | RNVC: 2

29 Jan 1983

5975-01-144-9373
Electrical-Electronic Equipment Chassis

011449373
636-5738-001: RNCC: 3 | RNVC: 2

31 Dec 1982

5975-01-583-1271
Electrical Components Tie Down Strap

015831271
123821-0001: RNCC: 3 | RNVC: 2

17 Mar 2010

5975-01-583-7039
Junction Box

015837039
11453120: RNCC: 3 | RNVC: 2

2 Apr 2010

5975-01-683-9623
Electrical-Electronic Equipment Chassis

016839623
783496-01: RNCC: 3 | RNVC: 2
NI-9147: RNCC: 5 | RNVC: 9
CRIO-9147: RNCC: 5 | RNVC: 9

16 Oct 2019

5975-01-681-1839
Electrical-Electronic Equipment Chassis

016811839
ACP-2000P4-00BE: RNCC: 3 | RNVC: 2

7 Jun 2019

5975-01-692-3542
Electronic Equipment Mounting Tray

016923542
UHK21622-1: RNCC: 3 | RNVC: 2

8 Dec 2020

5975-01-688-2326
Ground Support

016882326
K1019-1005-0101: RNCC: 3 | RNVC: 2

8 May 2020

5975-01-689-9518
Electrical Equipment Rack

016899518
6D32267G02: RNCC: 3 | RNVC: 1
3001F99 PC032: RNCC: D | RNVC: 9

17 Jul 2020

5975-01-516-3772
Electrical-Electronic Equipment Chassis

015163772
77425000-029: RNCC: 3 | RNVC: 2

6 Jan 2004

5975-01-516-1315
Electrical-Electronic Equipment Panel

015161315
233N3223-39: RNCC: 3 | RNVC: 2

19 Dec 2003

5975-01-516-3114
Stuffing Tube

015163114
AII-MTS-01-214APPENDIXBITEM19: RNCC: 3 | RNVC: 1
M19622/5-003: RNCC: 5 | RNVC: 1

31 Dec 2003

5975-01-515-9709
Electrical Grounding Plate

015159709
ILB1GNDSTP6000A-01: RNCC: 3 | RNVC: 2

15 Dec 2003

5975-01-514-7791
Flexible Nonmetallic Conduit

015147791
749-656-1-51.57: RNCC: 3 | RNVC: 2
5D0554-3: RNCC: 5 | RNVC: 2

4 Nov 2003

5975-01-643-4139
Electrical-Electronic Equipment Chassis

016434139
W017835-01: RNCC: 3 | RNVC: 2

31 Mar 2015

5975-01-644-3293
Electrical-Electronic Equipment Panel

016443293
507213-01: RNCC: 3 | RNVC: 2

30 Apr 2015

5975-01-643-4820
Electrical Conduit Coupling Nut

016434820
Z-428: RNCC: 3 | RNVC: 2

2 Apr 2015

5975-01-644-0331
Electrical Equipment Drawer

016440331
00603000-03B: RNCC: 3 | RNVC: 2

20 Apr 2015

5975-01-643-0186
Ground Rod

016430186
A30-9000-433: RNCC: 3 | RNVC: 2

17 Mar 2015

5975-01-687-1006
Electrical-Electronic Equipment Panel

016871006
16F80399-15: RNCC: 3 | RNVC: 2

18 Mar 2020

5975-01-690-9577
Mounting Plate

016909577
PA-1139MG: RNCC: 3 | RNVC: 2

11 Sep 2020

5975-01-691-6193
Blank Panel

016916193
404844-01: RNCC: 3 | RNVC: 2

20 Oct 2020

5975-01-688-3591
Electrical Equipment Drawer

016883591
900-72550-1: RNCC: 3 | RNVC: 1

14 May 2020

5975-01-693-3490
Electrical Equipment Rack

016933490
P9K07A: RNCC: 3 | RNVC: 2
1AAN016695: RNCC: 5 | RNVC: 2

5 Feb 2021

5975-01-694-7215
Switch Terminal Cover

016947215
673-1004-4077: RNCC: 3 | RNVC: 2

20 Apr 2021

5975-01-696-4238
Electrical Equipment Mounting Base

016964238
16E3853-3: RNCC: 3 | RNVC: 2
16E3853-3: RNCC: 5 | RNVC: 2

27 Jul 2021

5975-01-696-4125
Electronic Equipment Mounting Tray

016964125
16E5453-809: RNCC: 3 | RNVC: 2
16E5453-809: RNCC: 5 | RNVC: 2

26 Jul 2021

5975-01-696-8313
Guide Rail

016968313
15702828: RNCC: 3 | RNVC: 2

19 Aug 2021

5975-01-680-0535
Electrical-Electronic Equipment Chassis

016800535
C-301: RNCC: 3 | RNVC: 2
R107326-01: RNCC: 7 | RNVC: 2

17 Apr 2019

5975-01-533-5850
Fire Detector Controller

015335850
CM1-A: RNCC: 3 | RNVC: 2

20 Sep 2005

5975-01-141-6840
Cable Marker Sleeve

011416840
TMS-SCE-3/32-2.0-S2-9: RNCC: 3 | RNVC: 1
215511T97: RNCC: 5 | RNVC: 2
RNF-100-3/32X45/64 WHITE: RNCC: 5 | RNVC: 9
215511T97: RNCC: 7 | RNVC: 2

3 Nov 1982

5975-01-142-4184
Electrical Components Tie Down Strap

011424184
SST2SX30: RNCC: 3 | RNVC: 2

15 Nov 1982

5975-01-580-4605
Electrical Equipment Mounting Base

015804605
RMK598: RNCC: 3 | RNVC: 2

15 Dec 2009

5975-01-581-1822
Electrical-Electronic Equipment Chassis

015811822
0N802183-1: RNCC: 3 | RNVC: 2

7 Jan 2010

5975-01-581-4454
Sfp Module

015814454
AT-SPLX10/I: RNCC: 3 | RNVC: 2
AT-SPLX10/I: RNCC: 5 | RNVC: 2
L-46B-C-NM-B: RNCC: 5 | RNVC: 2
VCH115015P01: RNCC: 5 | RNVC: 2

16 Jan 2010

5975-01-581-6640
Junction Box Assembly

015816640
914021-1: RNCC: 3 | RNVC: 2

25 Jan 2010

5975-01-199-8717
Interconnecting Box

011998717
104-001-104: RNCC: 1 | RNVC: 2
82401A: RNCC: 3 | RNVC: 2

26 Jan 1985

5975-01-661-3227
Blank Panel

016613227
145E3446-1: RNCC: 3 | RNVC: 2

27 Feb 2017

5975-01-661-2041
Electrical Equipment Rack

016612041
72-D2-1018: RNCC: 3 | RNVC: 2

22 Feb 2017

5975-01-662-7036
Electrical Cable Protector

016627036
CE01167D22A: RNCC: 3 | RNVC: 2

17 Apr 2017

5975-01-662-8134
Mounting Bracket

016628134
6N-6249: RNCC: 3 | RNVC: 2

20 Apr 2017

5975-01-533-5077
Electrical-Electronic Equipment Chassis

015335077
8220-0: RNCC: 3 | RNVC: 2

16 Sep 2005

5975-01-513-2084
Electrical-Electronic Equipment Chassis

015132084
PXI-1006: RNCC: 3 | RNVC: 2

19 Sep 2003

5975-01-513-8299
Electrical Equipment Rack

015138299
11441915: RNCC: 3 | RNVC: 2

7 Oct 2003

5975-01-515-1549
Blank Panel

015151549
EC-29089-1: RNCC: 3 | RNVC: 2

17 Nov 2003

5975-01-641-1861
Electrical-Electronic Equipment Chassis

016411861
715543-1: RNCC: 3 | RNVC: 2

13 Jan 2015

5975-01-641-9332
Electrical Equipment Rack

016419332
RMT-GTA03: RNCC: 3 | RNVC: 2
RMT-GTA03: RNCC: 5 | RNVC: 2

6 Feb 2015

5975-01-642-3608
Electrical Equipment Cabinet

016423608
IP-RG-605-108: RNCC: 3 | RNVC: 2

24 Feb 2015

5975-01-641-9689
Junction Box Cover

016419689
115-00500-03: RNCC: 3 | RNVC: 2

9 Feb 2015

5975-01-641-8682
Electrical Conduit Locknut

016418682
114545-R15: RNCC: 3 | RNVC: 2

5 Feb 2015

5975-01-642-0611
Electrical-Electronic Equipment Chassis

016420611
U-ES30-30S: RNCC: 3 | RNVC: 2

11 Feb 2015

5975-01-642-5857
Electrical-Electronic Equipment Panel

016425857
102400-001: RNCC: 3 | RNVC: 2

3 Mar 2015

5975-01-209-4719
Electrical Conduit Adapter

012094719
4837K5: RNCC: 3 | RNVC: 2

30 May 1985

5975-01-531-3123
Audio Panel Assembly

015313123
D3548-2: RNCC: 3 | RNVC: 2

1 Jul 2005

5975-01-580-4389
Cable Collar

015804389
1001510: RNCC: 3 | RNVC: 2

15 Dec 2009

5975-01-658-3801
Electrical Equipment Rack

016583801
WS-X4948E-19CNTR=: RNCC: 3 | RNVC: 2

23 Sep 2016

5975-01-654-8893
Electrical Tie Down Mounting Base

016548893
016818: RNCC: 3 | RNVC: 2

12 May 2016

5975-01-531-0649
Electrical Equipment Cabinet

015310649
245161-B22: RNCC: 3 | RNVC: 2

21 Jun 2005

5975-01-206-8865
Electrical Cable Nipple

012068865
1-1464-06: RNCC: 3 | RNVC: 9

24 Apr 1985

5975-01-208-9667
Stored Cables Cover

012089667
10178479-7: RNCC: 3 | RNVC: 2
EC1024687: RNCC: 5 | RNVC: 9

21 May 1985

5975-01-235-0624
Electrical Equipment Rack

012350624
57977-40225-2: RNCC: 3 | RNVC: 2

24 Jun 1986

5975-01-139-3398
Cable Marker Sleeve

011393398
RNF-100-3/32-WH-SP: RNCC: 3 | RNVC: 1
215511T110: RNCC: 5 | RNVC: 2
RNF-100-3/32 WHITE: RNCC: 5 | RNVC: 9
10134292: RNCC: 6 | RNVC: 9
215511T110: RNCC: 7 | RNVC: 2

29 Sep 1982

5975-01-576-9501
Electrical-Electronic Equipment Chassis

015769501
DS-SL13R-AB: RNCC: 3 | RNVC: 2

20 Aug 2009

5975-01-580-3744
Electrical Equipment Drawer

015803744
8130654-02: RNCC: 3 | RNVC: 2

12 Dec 2009

5975-01-190-5483
Electrical Entrance Elbow

011905483
5-75: RNCC: 3 | RNVC: 9
5M2137-001: RNCC: 5 | RNVC: 2

27 Sep 1984

5975-01-190-6917
Electrical Components Tie Down Strap

011906917
SST1MX20: RNCC: 3 | RNVC: 2

29 Sep 1984

5975-01-650-7643
Electrical Equipment Rack

016507643
93074RX: RNCC: 3 | RNVC: 2

15 Dec 2015

5975-01-652-5467
Electrical Equipment Rack

016525467
3362473-29: RNCC: 3 | RNVC: 2

26 Feb 2016

5975-01-657-6335
Mounting Plate

016576335
39278-40122-3: RNCC: 3 | RNVC: 2

23 Aug 2016

5975-01-658-1004
Ground Rod

016581004
0199-1200-01: RNCC: 3 | RNVC: 2

13 Sep 2016

5975-01-524-0108
Electrical Equipment Mounting Base

015240108
10231-105: RNCC: 3 | RNVC: 2
17B9E1000-557: RNCC: 7 | RNVC: 2

21 Sep 2004

5975-01-523-2585
Guide Rail

015232585
RC11090-5P: RNCC: 3 | RNVC: 2
9D0090-5P: RNCC: 5 | RNVC: 2

26 Aug 2004

5975-01-508-8047
Chassis Base

015088047
151-006464-001: RNCC: 3 | RNVC: 2

3 Jun 2003

5975-01-510-0479
Electrical-Electronic Equipment Chassis

015100479
72B245024-102: RNCC: 3 | RNVC: 2

11 Jul 2003

5975-01-510-3917
Electrical Equipment Rack

015103917
A7381A: RNCC: 3 | RNVC: 2

18 Jul 2003

5975-01-508-3623
Guide Rail

015083623
910138-16: RNCC: 3 | RNVC: 2

19 May 2003

5975-01-511-5234
Electrical Tie Down Mounting Base

015115234
TMEH-S25-C0: RNCC: 3 | RNVC: 2

11 Aug 2003

5975-01-484-1840
Electrical Conduit Adapter

014841840
106801305: RNCC: 3 | RNVC: 2

21 Apr 2001

5975-01-483-9926
Cable Marker Sleeve

014839926
2540806-77: RNCC: 3 | RNVC: 2

13 Apr 2001

5975-01-484-4991
Cable Marker Sleeve

014844991
2540806-102: RNCC: 3 | RNVC: 2
2540806-102: RNCC: 5 | RNVC: 9

30 Apr 2001

5975-01-484-4363
Insulator Bracket Strap

014844363
10178-1511: RNCC: 3 | RNVC: 2

27 Apr 2001

5975-01-484-7381
Electrical Cable Nipple

014847381
BU-62-2: RNCC: 3 | RNVC: 2
25CRED: RNCC: 5 | RNVC: 9

7 May 2001

5975-01-478-9055
Electrical-Electronic Equipment Chassis

014789055
995-8178-002: RNCC: 3 | RNVC: 2

2 Oct 2000

5975-01-230-4993
Metallic Raceway

012304993
777057-1: RNCC: 3 | RNVC: 2

14 Apr 1986

5975-01-647-3189
Electrical Equipment Cabinet

016473189
CC72-3301: RNCC: 3 | RNVC: 2

18 Aug 2015

5975-01-648-7407
Electrical Equipment Shelf

016487407
M0DREF271335: RNCC: 3 | RNVC: 2

5 Oct 2015

5975-01-648-7614
Electrical-Electronic Equipment Panel

016487614
1656947-1: RNCC: 3 | RNVC: 2

6 Oct 2015

5975-01-648-7559
Electronic Equipment Mounting Tray

016487559
284A3703-17: RNCC: 3 | RNVC: 2

6 Oct 2015

5975-01-019-9472
Cable Marker Sleeve

010199472
1817317: RNCC: 3 | RNVC: 2

24 Apr 1976

5975-01-423-0197
Cable Collar

014230197
221B2004P2: RNCC: 3 | RNVC: 2

13 Dec 1995

5975-01-508-5077
Clamp Aircraft

015085077
16F4551-817: RNCC: 3 | RNVC: 2

22 May 2003

5975-01-483-9925
Cable Marker Sleeve

014839925
2540806-50: RNCC: 3 | RNVC: 2

13 Apr 2001

5975-01-484-4473
Electrical Equipment Mounting Base

014844473
RF-2310: RNCC: 3 | RNVC: 2
10007-1802: RNCC: 5 | RNVC: 2

28 Apr 2001

5975-01-283-2582
Junction Box

012832582
27R101-03: RNCC: 3 | RNVC: 2

2 Aug 1988

5975-00-179-4708
Electrical Equipment Shelf

001794708
900-37401-02: RNCC: 3 | RNVC: 9

24 Jan 1969

5975-01-573-0065
Electrical Equipment Rack

015730065
RAB 39-40RKW3: RNCC: 3 | RNVC: 2

3 Apr 2009

5975-01-573-9326
Electrical Conduit Adapter

015739326
710-833-02: RNCC: 3 | RNVC: 2

8 May 2009

5975-01-573-8509
Electrical Equipment Rack

015738509
RX1461-500: RNCC: 3 | RNVC: 2

6 May 2009

5975-01-573-8592
Electrical Equipment Rack

015738592
RX1635-600: RNCC: 3 | RNVC: 2

6 May 2009

5975-01-573-9314
Electrical Conduit Adapter

015739314
710-833-01: RNCC: 3 | RNVC: 2

8 May 2009

5975-00-179-1747
Electronic Equipment Mounting Tray

001791747
106591: RNCC: 3 | RNVC: 9
106591: RNCC: C | RNVC: 1

7 May 1969

5975-01-545-4309
Electrical-Electronic Equipment Chassis

015454309
8026500: RNCC: 3 | RNVC: 2

13 Nov 2006

5975-01-548-9492
Electrical Equipment Shelf

015489492
FL1-D: RNCC: 3 | RNVC: 2

7 Mar 2007

5975-01-435-2681
Electrical-Electronic Equipment Chassis

014352681
VX1406: RNCC: 3 | RNVC: 2
VX1406: RNCC: 5 | RNVC: 9

19 Aug 1996

5975-01-414-8776
Electrical Equipment Mounting Base

014148776
165861: RNCC: 3 | RNVC: 2

15 Jun 1995

5975-01-509-6177
Electrical Components Tie Down Strap

015096177
L653: RNCC: 3 | RNVC: 2

26 Jun 2003

5975-01-481-1043
Electrical Conductor Bushing

014811043
EH-00074-002: RNCC: 3 | RNVC: 2

18 Dec 2000

5975-01-482-2176
Electrical Equipment Rack

014822176
133-340049-5: RNCC: 3 | RNVC: 2
133-340049-5: RNCC: 3 | RNVC: 9

13 Feb 2001

5975-01-482-2175
Electrical Equipment Rack

014822175
133-340049-7: RNCC: 3 | RNVC: 2
133-340049-7: RNCC: 3 | RNVC: 9

13 Feb 2001

5975-01-278-8423
Electrical Box Connector

012788423
4208932: RNCC: 3 | RNVC: 2

10 May 1988

5975-01-233-3749
Electrical Equipment Rack

012333749
10-158039-1: RNCC: 3 | RNVC: 2

30 May 1986

5975-01-218-1730
Electrical-Electronic Equipment Chassis

012181730
4032296-952: RNCC: 3 | RNVC: 2
4032296-952: RNCC: 5 | RNVC: 1

8 Oct 1985

5975-01-570-8769
Electrical-Electronic Equipment Panel

015708769
68T058109-2015: RNCC: 3 | RNVC: 2

15 Jan 2009

5975-01-571-6443
Electrical Equipment Shelf

015716443
46298SZ: RNCC: 3 | RNVC: 2
46298SZ: RNCC: 3 | RNVC: 9
46298S: RNCC: 5 | RNVC: 9
10346707: RNCC: 6 | RNVC: 9

11 Feb 2009

5975-01-572-1627
Electronic Junction Rack

015721627
RR1061-4: RNCC: 3 | RNVC: 2

2 Mar 2009

5975-01-572-1632
Electronic Junction Rack

015721632
RR1061-7: RNCC: 3 | RNVC: 2

2 Mar 2009

5975-01-570-4039
Electrical Equipment Cabinet Subassy

015704039
204-57456-2: RNCC: 3 | RNVC: 2

29 Dec 2008

5975-01-571-5962
Blank Panel

015715962
E7736A: RNCC: 3 | RNVC: 2
E7736A: RNCC: 3 | RNVC: 9

10 Feb 2009

5975-01-571-7129
Blank Panel

015717129
E4468B: RNCC: 3 | RNVC: 2
E4468B: RNCC: 3 | RNVC: 9

13 Feb 2009

5975-01-572-1618
Electronic Junction Rack

015721618
RR1061-11: RNCC: 3 | RNVC: 2

2 Mar 2009

5975-01-539-9541
Electrical Wall Plate

015399541
13-5633V01: RNCC: 3 | RNVC: 2

4 May 2006

5975-01-542-3042
Electrical Tie Down Mounting Base

015423042
SB7000UG2NY5P: RNCC: 3 | RNVC: 2
CB4021V3N32P: RNCC: 3 | RNVC: 2
9D0272-105P: RNCC: 5 | RNVC: 2

28 Jul 2006

5975-01-423-8910
Electrical Equipment Drawer

014238910
BA350-JA: RNCC: 3 | RNVC: 2

13 Jan 1996

5975-01-455-6908
Rigid Metal Conduit

014556908
8317-1: RNCC: 3 | RNVC: 2

12 May 1998

5975-01-632-9014
Cable Splice Block

016329014
SBA10681: RNCC: 3 | RNVC: 2
15487312: RNCC: 5 | RNVC: 2

3 Nov 2014

5975-01-506-2322
Electrical Equipment Mounting Base

015062322
74A880604-1005: RNCC: 3 | RNVC: 2

25 Mar 2003

5975-01-507-4585
Electrical-Electronic Equipment Panel

015074585
DF055512-3: RNCC: 3 | RNVC: 9

29 Apr 2003

5975-01-221-2058
Electrical Equipment Cabinet

012212058
203AMOD1: RNCC: 3 | RNVC: 2

26 Nov 1985

5975-01-629-2214
Electrical Equipment Mounting Base

016292214
012A0036-2: RNCC: 3 | RNVC: 2

23 Jun 2014

5975-01-629-4130
Electrical Conduit Wye

016294130
31-301-21810: RNCC: 3 | RNVC: 2

30 Jun 2014

5975-01-630-1584
Electrical Equipment Rack

016301584
2227001: RNCC: 3 | RNVC: 2

26 Jul 2014

5975-01-629-8333
Electrical Equipment Shelf

016298333
010B226-002: RNCC: 3 | RNVC: 2

16 Jul 2014

5975-01-570-2534
Electrical-Electronic Equipment Panel

015702534
360-1130-001: RNCC: 3 | RNVC: 2

18 Dec 2008

5975-01-675-1318
Stuffing Tube

016751318
53112620: RNCC: 3 | RNVC: 2

23 Aug 2018

5975-01-676-5184
Electrical Equipment Rack

016765184
1010360-01: RNCC: 3 | RNVC: 2
1010360-01: RNCC: 3 | RNVC: 9

31 Oct 2018

5975-01-676-7757
Cable Seal Pack

016767757
SB-2G: RNCC: 3 | RNVC: 2

13 Nov 2018

5975-01-538-2014
Guide Rail

015382014
002513-01: RNCC: 3 | RNVC: 2

14 Mar 2006

5975-00-962-7189
Rigid Metal Conduit

009627189
775159-13: RNCC: 3 | RNVC: 2

1 Jan 1962

5975-01-423-7839
Electrical-Electronic Equipment Chassis

014237839
ODS-1095: RNCC: 3 | RNVC: 9

10 Jan 1996

5975-01-632-4661
Electrical Conduit Adapter

016324661
MIC-DCA-GD: RNCC: 3 | RNVC: 2

21 Oct 2014

5975-01-632-0037
Electrical Components Tie Down Strap

016320037
PRT1S-C0: RNCC: 3 | RNVC: 2

3 Oct 2014

5975-01-502-4465
Electrical Equipment Mounting Base

015024465
8197112G1: RNCC: 3 | RNVC: 2
40056580: RNCC: 5 | RNVC: 2

6 Nov 2002

5975-01-196-7100
Electrical Equipment Rack

011967100
9105-100: RNCC: 3 | RNVC: 2

14 Dec 1984

5975-01-205-5379
Electrical Components Tie Down Strap

012055379
MS3367-7: RNCC: 2 | RNVC: 2
5972090: RNCC: 5 | RNVC: 1
0538014: RNCC: 5 | RNVC: 2
PLT2I: RNCC: 5 | RNVC: 9
5975PL0822679: RNCC: 6 | RNVC: 9

9 Apr 1985

5975-01-627-7513
Cable Marker Sleeve

016277513
TMS-90-SCE-1-1/2: RNCC: 3 | RNVC: 2

25 Apr 2014

5975-01-627-8496
Electrical Conduit Adapter

016278496
T45RLDIW: RNCC: 3 | RNVC: 2

30 Apr 2014

5975-01-628-0064
Electrical-Electronic Equipment Chassis

016280064
HM34J-AUN-VV: RNCC: 3 | RNVC: 2
HM34J-AUN-VV: RNCC: 3 | RNVC: 9
3HE02786BA: RNCC: 5 | RNVC: 2

6 May 2014

5975-01-629-0865
Insulator Bracket

016290865
287A4131-26: RNCC: 3 | RNVC: 2

18 Jun 2014

5975-01-668-5852
Electrical-Electronic Equipment Chassis

016685852
SL-2U-AH110M-WD: RNCC: 3 | RNVC: 2

29 Nov 2017

5975-01-672-7582
Electrical-Electronic Equipment Chassis

016727582
ION002-AD: RNCC: 3 | RNVC: 9

15 May 2018

5975-01-496-2381
Electrical-Electronic Equipment Chassis

014962381
548-5987-004: RNCC: 3 | RNVC: 2

8 Apr 2002

5975-01-496-0861
Electrical-Electronic Equipment Chassis

014960861
687-3791-001: RNCC: 3 | RNVC: 2

2 Apr 2002

5975-01-476-3105
Panel Plug

014763105
02-949.0: RNCC: 3 | RNVC: 2

7 Jul 2000

Load More Results