Premium Information is available for this item - Upgrade for $1 a day
5315-01-526-0691
Cotter Pin
5315015260691 015260691 B.18.24-2004 AEP33X002022SE4A11 AEP33X020022SE4A11 B1886020022EAU
A half round, cylindrical, or flat piece of metal, bent to form a straight or crimped two-pronged device with an eye at one end, for inserting in a hole drilled at right angle to the axis of the stud, shaft, or like item. Its ends are separable or one end is bent to hold it in place. View more Cotter Pin
Managed by United States
NSN Created on 7 Dec 2004
Data Last Changed
November 2023
November 2023
NATO Update Count
6
6
NATO Data Quality
Marketplace 5315-01-526-0691
Need Help?
Request a Quotation from participating marketplace vendors
Request a Quotation from participating marketplace vendors
Related Documents 5315-01-526-0691 5+ Documents (More...)
5310-01-665-4797 5310016654797 016654797 is a nut, flat on top and bottom having 6 flat sides. for items which have internal tapered or straight (parallel) pipe threads, specific electrical conduit size designation, and which when installed, provide a method of tightening to lock the connection, see locknut, electrical conduit. see also locknut, tube fitting. for items having a thickness (or height) exceeding two times the width across the flats, use post, electrical-mechanical equipment. (when height or thickness and/or width across the flats is designated as a tolerance dimension, the maximum dimension will be used to determine compliance.)
5310-01-664-1425 5310016641425 016641425 is a washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. the hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). the thickness cannot exceed 25 percent of the largest outside dimension. when the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. the maximum tolerance is applied to dimensions and used as a determining factor. items with separable lamination use shim. for items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. excludes disk, valve, graphite impregnated and lubricated items.
5315-01-529-5076 5315015295076 015295076 is a headed, cylindrically-shaped item having a solid shank for fitting into corresponding holes, used for aligning or fastening. it may have welding projections. it also may contain holes drilled perpendicular to axial centerline. excludes pin, eccentric.
5310-01-665-0650 5310016650650 016650650 is a washer which is usually round with a centrally located hole. its edges and two bearing surfaces are so designed that applied pressure brings into play the spring tension and/or frictional locking principle which materially resists any tendency toward turning. it may be made of one or two pieces
5310-01-672-4400 5310016724400 016724400 is a washer which is usually round with a centrally located hole. its edges and two bearing surfaces are so designed that applied pressure brings into play the spring tension and/or frictional locking principle which materially resists any tendency toward turning. it may be made of one or two pieces
Restrictions 5315-01-526-0691
5315-01-526-0691 is a Cotter Pin Demilitarization of this item has been confirmed and is not currently subject to changes. This item is considered a low risk when released from the control of the Department of Defense. The item may still be subject to the requirements of the Export Administration Regulations (EAR) and the Code of Federal Regulations (CFR). This item is not suspected to be hazardous. This item does not contain a precious metal.
End Users 5315-01-526-0691
- US Army (A919)
- Effective Date:
- 1 Apr 2006
- Former MOE Rule:
- A187
- Supplementary Receivers:
- BF
- US Marine Corps (MC47)
- Effective Date:
- 1 Apr 2006
- Former MOE Rule:
- MC10
- US Navy (N9BZ)
- Effective Date:
- 1 Dec 2013
- Supplementary Collaborators:
- GG
- Australia (ZA01)
- Effective Date:
- 1 Apr 2010
- Canada (ZC01)
- Effective Date:
- 1 Apr 2007
Approved Sources 5315-01-526-0691
- Part Number
- Manufacturer
- Status
- AEP33X002022SE4A11
- Manufacturer
- 05047 - The American Society Of Mechanical (Active)
- Primary Buy
- Primary Buy
- B.18.24-2004
- 05047 - The American Society Of Mechanical (Active)
- Incomplete Secondary Reference
- Incomplete Secondary Reference
- AEP33X020022SE4A11
- 05047 - The American Society Of Mechanical (Active)
- Canceled/Obsolete
- Canceled/Obsolete
- B1886020022EAU
- 80204 - American National Standards (Active)
- Canceled/Obsolete
- Canceled/Obsolete
Weapon Systems (WSDC) 5315-01-526-0691
DLA Procurement Analysis 5315-01-526-0691
- Last Stock Position:
- 3660 In Stock
- DLA Administrative Lead Time:
- Subscribe
- DLA Production Lead Time:
- Subscribe
Management Data 5315-01-526-0691
- Effective Date
- Organization
- Unit of Issue
- Unit Price
- Qty Unit Pack
- Unit of Issue
- Oct 2022
- US Marine Corps (DM)
- EA
- Subscribe
- EA
- Dec 2021
- Defense Logistics Agency (DS)
- EA
- Subscribe
- EA
- Oct 2021
- Department of the Army (DA)
- EA
- Subscribe
- EA
- Oct 2020
- Defense Logistics Agency (DS)
- EA
- Subscribe
- EA
- Oct 2019
- Department of the Army (DA)
- EA
- Subscribe
- EA
- MOE
- USC
- Code
- Statement
- Order of Use
- Jump To Code
- Qty Per Assy
- UOM
- Technical Document
- Quantative Expression
- Code
- Department of the Navy (DN)
- N
- R
- Refer To Lw155 Howitzer
- LW155 HOWITZER
- R
- Defense Logistics Agency (DS)
- I
- R
- Refer To Lw155 Howitzer
- LW155 HOWITZER
- R
Army
- Materiel Category and Inventory Manager:
- T
- Industrial Supplies (DLA/GSA Items)
- Appropriation and Budget Activity:
- 2
- Stock Fund Secondary Items
- Management Inventory Segment:
- 2
- Non-Repairable Items(Exclusive of Insurance and Provisioning Items)
This code will be used to identify items, which are not reparable.
- Weapons System / End Item / Homogeneous Group:
- 00
- DLA/GSA Material
DLA/GSA-Managed Items that cannot be identified to a specific Army Weapons Systems/End Item
- Accounting Requirements:
- X
- Expendable item.An item of Army property coded with an ARC of X in the AMDF. Expendable items require no formal accountability after issue from a stock record account.Commercial and fabricated items similar to items coded X in the AMDF are considered expendable items.
Navy
- Cognizance:
- 9B
- Navy-owned stocks of DLA material
Naval Inventory Control Point, Mechanicsburg
Marine Corps
- Stores Account:
- 1
- Stock Fund Account Item
- Combat Essentiality:
- 5
- Critical Repair Part to a Combat Essential End Item
- Echelon Management:
- B2
- Operational Test:
- No Special Procedures
- Physical Category:
- 1
- Bin
NATO Stock Numbers Related to 5315-01-526-0691
5315-99-127-8053 5315-14-559-8871 5315-27-015-8498 5315-34-030-5147 5315-27-052-1591 5315-34-041-5458 5315-99-747-6160 5315-99-727-3555 5315-32-020-9644 2805-22-256-5016 5315-19-004-3934 5315-99-460-8439 5315-66-155-9357 5315-12-341-6630 5315-12-700-2686 5315-27-015-7428 5315-12-173-6583 5315-16-002-1706
Freight Information 5315-01-526-0691
5315-01-526-0691 has freight characteristics managed by the Southwestern Power Administration.It has a National Motor Freight Classification (NMFC) of 094380. A Sub NMFC of X. It has a NMFC Description of COTTER PINS/SPRING COTTERS IRON. 5315-01-526-0691 is rated as class 50 when transported by Less-Than Truckload (LTL) freight. It has a Uniform Freight Classification (UFC) number of 49340 which rates the freight between FCL and LCL. 5315-01-526-0691 has a variance between NMFC and UFC when transported by rail and the description should be consulted. It has a Water Commodity Code (WCC) of 713 for ocean manifesting and military sealift. 5315-01-526-0691 is not classified as a special type of cargo when transported by water. 5315-01-526-0691 is not a consolidation and does not exceed 84" in any dimension. It should be compatible with a standard 72" Aircraft Cargo Door when transported by air.
Packaging Data 5315-01-526-0691
- Responsible Activity
- Packaging Data Source
- Primary Inventory Control Activity (PICA)
- --
Item Pack Level (Unpackaged)
- Item Size
- Item Weight
- Characteristics
- Weight/Dimensions Category
- Fragility
- Item Preservation
- Item Weight
- --
- --
- Bare Metal Item
- 2lb or less, one dimension 2" or less, other dimensions less than 24"
- Above 110G
- No Requirement
- --
Unit Pack Level (Packaged)
- Quantity per Pack
- Unit Size
- Unit Weight
- Unit Cube
- Preservation Method
- Cleaning/Drying
- Unit Size
- --
- --
- --
- --
- Physical Protection
- Any Suitable Process
- --
- Preservation Material
- Wrapping Material
- Cushioning/Dunnage
- Cushioning Thickness
- Container
- Special Marking
- Wrapping Material
- No Requirement
- No Requirement
- No Requirement
- Not Applicable
- PPP-B-566, PPP-B-676, or ASTM-D5118, Folding, Setup or Fiberboard Box
- No special marking
- No Requirement
Intermediate Pack Level
- Quantity of Unit Packs
- Container
- PPP-B-566, PPP-B-676, or ASTM-D5118, Folding, Setup or Fiberboard Box
Procurement History 5315-01-526-0691 8 Records
- Contract
- Date
- CAGE
- Quantity
- Net Price
- Std Price
- CAGE
- SPE4A623V109C
- 03 Apr 2023
- Subscribe
- 1958
- Subscribe
- Subscribe
- Subscribe
- SPE4A621PM697
- 17 Jun 2021
- Subscribe
- 1007
- Subscribe
- Subscribe
- Subscribe
- SPE5E017V4343
- 30 Jun 2017
- Subscribe
- 916
- Subscribe
- Subscribe
- Subscribe
- SPE5E716M2767
- 09 May 2016
- Subscribe
- 290
- Subscribe
- Subscribe
- Subscribe
- SPE5E916M1181
- 07 Mar 2016
- Subscribe
- 48
- Subscribe
- Subscribe
- Subscribe
- SPE5E716M0031
- 02 Oct 2015
- Subscribe
- 378
- Subscribe
- Subscribe
- Subscribe
- SPE5E714V6184
- 04 Sep 2014
- Subscribe
- 464
- Subscribe
- Subscribe
- Subscribe
- SPE5E714V3746
- 05 May 2014
- Subscribe
- 382
- Subscribe
- Subscribe
- Subscribe
Contracting Technical Data File (CTDF) 5315-01-526-0691 February 2021
Criticality and Quality
- Critical Item Code:
- Flight Safety:
- Life Support:
- Certified Samples:
- Serialization:
- First Article Test (FAT):
- Certificate of Quality Compliance:
- Production Lot Testing:
- Special Testing:
- Qualified Products List (QPL):
Commercial Properties
- Government Furnished Material:
- Government Furnished Tooling:
- Government Furnished Property:
- Price Evaluation Code:
- Diminshing Manufacturing Sources:
- Warranty:
- Commerical Off The Shelf (COTS):
- End Item Application:
- Auctioning Candidate:
- Source of Procurement:
- Contract Option:
Restrictions
- Boeing Rights Guard:
- Export Controlled:
- Controlled Technical Data Package (TDP):
- Restricted Technical Data Package (TDP):
- Contains Classified Material
- Weapons System Indicator Code (WSIC):
- F
Packaging Requirements
- Packaging Determination Table:
- Packaging Review Code:
- Special Packaging Instruction Number (SPIN):
- Special Packaging Instruction Number Revision:
- Special Packaging Instruction Number Date:
- Pallet Reference Number Required: