Premium Information is available for this item - Upgrade for $1 a day
5310-01-357-5755
Flat Washer
5310013575755 013575755 ED0075550290-S 76702 7776702
A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use SHIM. For items fabricated from ceramic or electrically rated materials by specification or industry standards use INSULATOR (1), WASHER. Excludes DISK, VALVE, graphite impregnated and lubricated items. View more Flat Washer
November 2023
8
Marketplace 5310-01-357-5755
Request a Quotation from participating marketplace vendors
Related Documents 5310-01-357-5755 5+ Documents (More...)
the Cage Code 76702.
What is CAGE Code 76702?
) Troy 6. 76702 Quality Tool And Abrasives Inc is a Cancelled Without Replacement Commercial Supplier
with the Cage Code 76702.
) Troy 6. 76702 Quality Tool And Abrasives Inc is a Cancelled Without Replacement Commercial Supplier
with the Cage Code 76702.
Restrictions 5310-01-357-5755
5310-01-357-5755 is a Flat Washer Demilitarization of this item has been confirmed and is not currently subject to changes. This item is considered a low risk when released from the control of the Department of Defense. The item may still be subject to the requirements of the Export Administration Regulations (EAR) and the Code of Federal Regulations (CFR). This item is not suspected to be hazardous. This item does not contain a precious metal.
Approved Sources 5310-01-357-5755
- Part Number
- Manufacturer
- Status
- ED0075550290-S
- Manufacturer
- 2X179 - Lombardini U.S.A., Inc (Active)
- Primary Buy
- Primary Buy
- ED0075550290-S
- A1212 - Lombardini Srl (Active)
- Secondary Buy
- Secondary Buy
- 76702
- 66289 - Wisconsin Motors Llc (Active)
- Canceled/Obsolete
- Canceled/Obsolete
- 7776702
- 62445 - Deutz Corporation (Active)
- Canceled/Obsolete
- Canceled/Obsolete
Weapon Systems (WSDC) 5310-01-357-5755
DLA Procurement Analysis 5310-01-357-5755
Management Data 5310-01-357-5755
- Effective Date
- Organization
- Unit of Issue
- Unit Price
- Qty Unit Pack
- Unit of Issue
- Apr 2021
- Defense Logistics Agency (DS)
- EA
- Subscribe
- EA
- Oct 2020
- US Marine Corps (DM)
- EA
- Subscribe
- EA
- Mar 2020
- Department of the Navy (DN)
- EA
- Subscribe
- EA
- Oct 2019
- Department of the Air Force (DF)
- EA
- Subscribe
- EA
- MOE
- USC
- Code
- Statement
- Order of Use
- Jump To Code
- Qty Per Assy
- UOM
- Technical Document
- Quantative Expression
- Code
- Department of the Navy (DN)
- N
- A
- Consolidated With 5310-01-453-7078
- A
- Defense Logistics Agency (DS)
- I
- A
- Consolidated With 5310-01-453-7078
- A
Air Force
- Fund:
- SF
- Stock fund applicable to items managed for the Air Force by the respective Inventory Control Point
- Budget:
- 9
- 57X4921.070 - General Support DIV - Air Force decentralized managed expense items (ERRC XB3, XF3) with a unit cost of less than $250,000 that are requisitioned/procured at base (retail) level from DLA, GSA, Army, Navy, Depot Maintenance Service, Air Force Industrial Fund (AFMC), local manufacture and commercial vendors
- Aggregation Code:
- SX
- SICA RESIDUAL MMAC-OC-ALC
- Price Validation Code:
- N
- The current standard price in Catalog Management Data (CMD) has not analyzed or coded for LP/LM.
The price has not been analyzed or reviewed for accuracy.
ZOP or Standard price challenges are permissible but must be supported with adequate justification. However, if coded for Local Purchase (LP) or Fabrication/Manufacture as indicated with an (LM) Acquisition Advice Code of “L” or “F”, then it must be evaluated locally where purchased or fabricated.
Navy
- Cognizance:
- 9B
- Navy-owned stocks of DLA material
Naval Inventory Control Point, Mechanicsburg
Marine Corps
- Stores Account:
- 1
- Stock Fund Account Item
- Combat Essentiality:
- 2
- Non-Critical Repair Part
- Echelon Management:
- B2
- Operational Test:
- No Special Procedures
NATO Stock Numbers Related to 5310-01-357-5755
Procurement History 5310-01-357-5755 5 Records
- Contract
- Date
- CAGE
- Quantity
- Net Price
- Std Price
- CAGE
- SPE5E818V7751
- 25 Jun 2018
- Subscribe
- 6
- Subscribe
- Subscribe
- Subscribe
- SPE5E818V7385
- 11 Jun 2018
- Subscribe
- 4
- Subscribe
- Subscribe
- Subscribe
- SPE5E017V0841
- 17 Nov 2016
- Subscribe
- 3
- Subscribe
- Subscribe
- Subscribe
- SPE5E416V8714
- 13 Jul 2016
- Subscribe
- 1
- Subscribe
- Subscribe
- Subscribe
- SPE5E815M4204
- 01 Jul 2015
- Subscribe
- 4
- Subscribe
- Subscribe
- Subscribe
Contracting Technical Data File (CTDF) 5310-01-357-5755 February 2021
Criticality and Quality
- Critical Item Code:
- Flight Safety:
- Life Support:
- Certified Samples:
- Serialization:
- First Article Test (FAT):
- Certificate of Quality Compliance:
- Production Lot Testing:
- Special Testing:
- Qualified Products List (QPL):
Commercial Properties
- Government Furnished Material:
- Government Furnished Tooling:
- Government Furnished Property:
- Price Evaluation Code:
- Diminshing Manufacturing Sources:
- Warranty:
- Commerical Off The Shelf (COTS):
- End Item Application:
- Auctioning Candidate:
- Source of Procurement:
- Contract Option:
Restrictions
- Boeing Rights Guard:
- Export Controlled:
- Controlled Technical Data Package (TDP):
- Restricted Technical Data Package (TDP):
- Contains Classified Material
- Weapons System Indicator Code (WSIC):
- Z
Packaging Requirements
- Packaging Determination Table:
- Packaging Review Code:
- Special Packaging Instruction Number (SPIN):
- Special Packaging Instruction Number Revision:
- Special Packaging Instruction Number Date:
- Pallet Reference Number Required: