Premium Information is available for this item - Upgrade for $1 a day
3040-01-304-1963
Shouldered Shaft
3040013041963 013041963 701-5927906 PIE 701-5927906 PC 3 701-5927906
A shaft having two or more different diameters (greater than 0.031 inches (0.79 millimeter)) along its length. It must have one or more of the following conditions: a specified surface finish designation in the range 1 to 125 microinches (0.025 to 3.2 micrometers) arithmetical average (AA), machined peripheral flat(s), circular groove(s), keyway(s), splines, threads, or holes. The ends and/or shoulders may be machined to accommodate bearings, couplings, and the like. It is not designed for use in aligning by fitting into corresponding holes of another item. For items used to support rotating members see AXLE(1), SHOULDERED. For items not having any of the above conditions see PIN, SHOULDER, HEADLESS. Excludes SHAFT(1), STRAIGHT; and AXLE(1), STRAIGHT. View more Shouldered Shaft
May 2023
3
Marketplace 3040-01-304-1963
Request a Quotation from participating marketplace vendors
Related Documents 3040-01-304-1963 5+ Documents (More...)
BUY NE FedMall Updated Every Day 3040-01-304-1963 RQST NE Updated Every Day 3040-01-304-1963 RQST
Updated Every Day 3040-01-304-1963 RQST NE Related Documents 3040-01-304-1963 5+ Documents ( More...
Shouldered Shaft 3040013041963 013041963 a day Upgrade your Account Upgrade 3040-01-304- https/
www.nsnlookup.com /fsg-47/fsc-4730/ca 4730-21-852-3750 Lubrication Fitting 4730218523750218523750 3040-01-304-1963
SH 3 PC 1 701-5927906 PC 1 701-5927906 A pulley with one or more grooved faces or rims of the same diameter
Shouldered Shaft 3040013041963 013041963 for $1 a day Upgrade your Account Upgrade 3040-01-304-
SH 701-5927906 SH3 PC 4 A washer having a centrally located hole with a solid or laminated cross-section
SH Reference RNCC C RNVC 1 DAC E 701-5927906 https/ https//www.nsnlookup.com /fsg-53/fsc-5310/us 5310
PC 1 701-5927906 A pulley with one or more grooved faces or rims of the same diameter SH 3 PC 1701-5927906
PC 1701-5927906 A pulley with one or more grooved faces or rims of BUY NE FedMall PIE 701-5927906 PC
Restrictions 3040-01-304-1963
3040-01-304-1963 is a Shouldered Shaft that does not have a nuclear hardened feature or any other critical feature such as tolerance, fit restriction or application. This item is considered a low risk when released from the control of the Department of Defense. The item may still be subject to the requirements of the Export Administration Regulations (EAR) and the Code of Federal Regulations (CFR). This item is not suspected to be hazardous. This item does not contain a precious metal.
Import and Export 3040-01-304-1963
- Schedule B
- Subscribe to View Schedule B
- HTS Code
- Subscribe to View HTS Code
End Users 3040-01-304-1963
- US Navy (N9BC)
- Effective Date:
- 1 Aug 2004
- Former MOE Rule:
- N9CD
- Supplementary Collaborators:
- HD
Approved Sources 3040-01-304-1963
- Part Number
- Manufacturer
- Status
- 701-5927906 PC 3
- Manufacturer
- 53711 - Naval Sea Systems Command (Active)
- Primary Buy
- Primary Buy
- 701-5927906 PIE
- 53711 - Naval Sea Systems Command (Active)
- Advisory Reference
- Advisory Reference
- 701-5927906
- 53711 - Naval Sea Systems Command (Active)
- Informational Drawing
- Informational Drawing
Datasheet 3040-01-304-1963
- Characteristic
- Specifications
- FIIG
- Specifications
- A23200
- Material [MATT]
- Steel
- First End Style [AAGZ]
- Circular Grooved
- First End Groove Width [AAHG]
- 0.3125 Inches Nominal
- First End Groove Diameter [AAHH]
- 1.2500 Inches Nominal
- First End Distance From End To Groove [AMCY]
- 0.437 Inches Nominal
- First End Diameter [AMDL]
- 1.7500 Inches Nominal
- End Similarity [AAHN]
- Not Identical
- Second End Style [AAHP]
- Unthreaded Cross Drilled
- Second End Diameter [AMFZ]
- 2.2500 Inches Nominal
- Second End Hole Diameter [AMGS]
- 0.1875 Inches Nominal
- Second End Distance From Hole Center To End [AMGT]
- 1.906 Inches Nominal
- Largest Step Diameter [CSPY]
- 2.250 Inches Nominal
- Overall Length [ABHP]
- 4.312 Inches Nominal
- Step Quantity [ATPC]
- 4
Weapon Systems (WSDC) 3040-01-304-1963
DLA Procurement Analysis 3040-01-304-1963
Management Data 3040-01-304-1963
Navy
- Cognizance:
- 9B
- Navy-owned stocks of DLA material
Naval Inventory Control Point, Mechanicsburg
Similar Supply Items to 3040-01-304-1963
Freight Information 3040-01-304-1963
3040-01-304-1963 has freight characteristics.It has a National Motor Freight Classification (NMFC) of 126900. A Sub NMFC of Z. It has a NMFC Description of POWER TRANS SHAFTING/SHAFTS. 3040-01-304-1963 is rated as a variable freight class when transported by Less-Than Truckload (LTL) freight. It has a Uniform Freight Classification (UFC) number of 65750 which rates the freight between FCL and LCL. 3040-01-304-1963 has a variance between NMFC and UFC when transported by rail and the description should be consulted. It has a Water Commodity Code (WCC) of 593 for ocean manifesting and military sealift. 3040-01-304-1963 is not classified as a special type of cargo when transported by water. 3040-01-304-1963 is not a consolidation and does not exceed 84" in any dimension. It should be compatible with a standard 72" Aircraft Cargo Door when transported by air.
Contracting Technical Data File (CTDF) 3040-01-304-1963 October 2021
Criticality and Quality
- Critical Item Code:
- X
- Flight Safety:
- Life Support:
- Certified Samples:
- Serialization:
- First Article Test (FAT):
- Certificate of Quality Compliance:
- Production Lot Testing:
- Special Testing:
- Qualified Products List (QPL):
Commercial Properties
- Government Furnished Material:
- Government Furnished Tooling:
- Government Furnished Property:
- Price Evaluation Code:
- Diminshing Manufacturing Sources:
- Warranty:
- Commerical Off The Shelf (COTS):
- End Item Application:
- Auctioning Candidate:
- Source of Procurement:
- Contract Option:
Restrictions
- Boeing Rights Guard:
- Export Controlled:
- Controlled Technical Data Package (TDP):
- Restricted Technical Data Package (TDP):
- Contains Classified Material
- Weapons System Indicator Code (WSIC):
- F
Packaging Requirements
- Packaging Determination Table:
- Packaging Review Code:
- Y
- Special Packaging Instruction Number (SPIN):
- Special Packaging Instruction Number Revision:
- Special Packaging Instruction Number Date:
- Pallet Reference Number Required: