TM 9-2320-209-34P F Reparable item. When uneconomically reparable, condemn and dispose at the direct support level. H Reparable item. When uneconomically reparable, condemn and dispose at the general support level. D Reparable item, When beyond lower level repair capability, return to depot. Condemnation and disposal not authorized below depot level. L Reparable item. Repair, condemnation, and disposal not authorized below depot/specialized repair activity level. A Item requires special handling or condemnation procedures because of specific reasons (i.e., precious metal content, high dollar value, critical material or hazardous material). Refer to appropriate manuals/directives for specific instructions. c. National Stock Number. Indicates the National stock number assigned to the item and will be used for requisitioning purposes. d. Part Number. Indicates the primary number used by the manufacturer (individual, company, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications standards, and inspection requirements, to identify an item or range of items. NOTE: When a stock numbered item is requisitioned, the repair part received may have a different part number than the part number than the part being replaced. e. Federal Supply Code for Manufacturer (FSCM). The FSCM is a 5 digit numeric code listed in SB 708-42 which is used to identify the manufacturer, distributor, or Government agency, etc. f. Description. Indicates the Federal item name and, if required, a minimum description to identify the item. Items that are included in kits and sets are listed below the name of the kit or set with the quantity of each item in the kit or set indicated in the quantity incorporated in unit column. When the part to be used differs between serial numbers of the same model, the effective serial numbers are shown as the last line of the description. In the Special Tools List, the initial basis of issue (BOI) appears as the last line in the entry for each special tool, TMDE, and support equipment. When density of equipments supported exceeds density spread indicated in the basis of issue, the total authorization is increased accordingly. g. Unit of Measure (U/M). Indicates the standard of the basic quantity of the listed item as used in performing the actual maintenance function. This meausre is expressed by a two-character alphabetical abbreviation (e.g., ea, in, pr, etc.). When the unit of measure differs from the unit of issue, the lowest unit of issue that will satisfy the required units of measure will be requisitioned. h. Quantity Incorporated in Unit. Indicates the quantity of the item used in the breakout shown on the illustration figure, which is prepared for a functional group or an assembly. A “V” appearing in this column in lieu of a quantity indicates that no specific quantity is applicable, (e.g., shims, spacers, etc.). 4. Special Information. a. Usable on codes are shown in the description column. Uncoded items are applicable to all models, unless otherwise indicated by model application in the description column, Identification of the usable on codes used in this publication are: Code Used On AA All models equipped with gasoline engine Model OA-331 AB All models equipped with the multi-fuel LDS- 427-2 engine AC All models equipped with multi-fuel engines LD-465-1, LD-465-1C or LDT-465-1 C AD All models equipped with front winch AE All models equipped with power takeoff b. References to the M44A2 series apply only to the multifuel clean air engine (LDT 465-1 C, NSN 2815-00- 103-2642). Some figures include the words “clean air” in parentheses to designate this. c. Detailed manufacturing instructions for items source coded to be manufactured or fabricated are found in TM 9-2320-209-20/1 (TM 9-2320-209-20, gasoline models only) and TM 9-2320-209-34 (TM 9-2320-209-35, gasoline models only). Bulk materials required to manufacture items are listed in the Bulk Material Group 9501 of this manual. d. Detailed assembly instructions for items source coded to be assembled are found in TM 9-2320-209- 20/1 (TM 9-2320-209-20, gasoline models only) and TM 9- 2320-209-34 (TM 9-2320-209-35, gasoline models only). Assembly components are listed immediately following the item to be assembled. Repair parts kits and gasket sets appear as the last entries in the repair parts listing for the figure in which its parts are listed as repair parts. Change 1 vii