TM-9-2520-272-40 Direct Support for M113A3 X200-4A Transmission 2520-01-397-1074 Download
Page 23 of 620
TM 9-2520-272-40 xiii TABLE OF CONTENTS – (Continued) Page No. WP Sequence No. REPAIR BEVEL GEAR ASSEMBLY ................................................................................................ WP 0059 Figure 1. Input Oil Pump Driven Gear Removal .................................................................. WP 0059-2 Figure 2. Input Oil Pump Drive Gear and Bearing Removal ................................................ WP 0059-2 Figure 3. Scavenge Tube Assembly and Output Oil Pump Assembly Removal ................. WP 0059-3 Figure 4. Push-Start Valve Body (Check Valve Body) Removal ......................................... WP 0059-4 Figure 5. Reverse Signal Tube Clamp Removal ................................................................. WP 0059-5 Figure 6. Reverse Signal Tube Removal ............................................................................. WP 0059-6 Figure 7. Connector Removal .............................................................................................. WP 0059-7 Figure 8. Elbow Removal ..................................................................................................... WP 0059-8 Figure 9. Input and Scavenge Pump Assembly Removal ................................................... WP 0059-8 Figure 10. Diaphragm Assembly Hardware Removal .......................................................... WP 0059-9 Figure 11. Diaphragm Assembly Removal .......................................................................... WP 0059-9 Figure 12. Seal Rings Removal ........................................................................................... WP 0059-10 Figure 13. Seal Rings Installation ........................................................................................ WP 0059-10 Figure 14. Diaphragm Assembly Installation ....................................................................... WP 0059-11 Figure 15. Input and Scavenge Pump Assembly Installation .............................................. WP 0059-11 Figure 16. Elbow Installation ................................................................................................ WP 0059-12 Figure 17. Connector Installation ......................................................................................... WP 0059-12 Figure 18. Reverse Signal Tube Clamp Installation ............................................................ WP 0059-13 Figure 19. Reverse Signal Tube Installation ........................................................................ WP 0059-13 Figure 20. Push-Start Valve Body (Check Valve Body) Installation .................................... WP 0059-14 Figure 21. Output Oil Pump Assembly and Scavenge Tube Assembly Installation ............ WP 0059-15 Figure 22. Bearing Installation on Input Oil Pump Drive Gear ............................................. WP 0059-16 Figure 23. Input Oil Pump Drive Gear Installation ............................................................... WP 0059-16 Figure 24. Input Oil Driven Gear Installation ........................................................................ WP 0059-17 REPLACE HYDROSTATIC PUMP AND MOTOR ASSEMBLY ....................................................... WP 0060 Figure 1. Eyebolt Installation................................................................................................WP 0060-1 Figure 2. Hydrostat Removal ............................................................................................... WP 0060-2 Figure 3. 13-Tooth Hydrostatic Drive Gear Removal ........................................................... WP 0060-3 Figure 4. 32-Tooth Hydrostatic Gear Removal .................................................................... WP 0060-3 Figure 5. 32-Tooth Hydrostatic Gear Installation ................................................................. WP 0060-4 Figure 6. 13-Tooth Hydrostatic Drive Gear Installation........................................................ WP 0060-5 Figure 7. Eyebolt Removal ................................................................................................... WP 0060-5 Figure 8. Hoisting Hydrostatic .............................................................................................. WP 0060-6 Figure 9. Hydrostat Aligned on Center Housing .................................................................. WP 0060-6 Figure 10. Hydrostat Installation .......................................................................................... WP 0060-7 REPLACE GOVERNOR ASSEMBLY, GOVERNOR BODY ASSEMBLY, AND GOVERNOR DRIVE GEAR .............................................................................................................. WP 0061 Figure 1. Governor Access Cover and Governor Assembly Removal ................................ WP 0061-1 Figure 2. Governor Body Assembly and Governor Drive Gear Removal ............................ WP 0061-2 Figure 3. Governor Drive Gear and Governor Body Assembly Installation ......................... WP 0061-3 Figure 4. Governor Access Cover and Governor Assembly Installation ............................. WP 0061-4 FINAL ADJUSTMENTS OVERVIEW ................................................................................................ WP 0062 Table 1. Final Adjustment Procedures by Work Package ................................................... WP 0062-1 CHECK OUTPUT SHAFT DRAG, LEFT AND RIGHT SIDE ............................................................ WP 0063 Figure 1. Dimpled Washer on Output Flange ...................................................................... WP 0063-2 Figure 2. Bent Tab on Output Flange .................................................................................. WP 0063-3 TORQUE WRENCH CHECK ............................................................................................................ WP 0064 Figure 1. Torque Wrench Check .......................................................................................... WP 0064-3