TM-9-2520-272-40 Direct Support for M113A3 X200-4A Transmission 2520-01-397-1074 Download
Page 22 of 620
TM 9-2520-272-40 xii TABLE OF CONTENTS – (Continued) Page No. WP Sequence No. Figure 14. Bar and Stud Assembly for Retaining Ring Removal ........................................ WP 0056-11 Figure 15. Bar and Stud Assembly and Compressor Installed for Retaining Ring Removal ..................................................................................................... WP 0056-11 Figure 16. First Clutch Piston Removal ............................................................................... WP 0056-12 Figure 17. First Clutch Piston Seals Removal ..................................................................... WP 0056-12 Figure 18. First Clutch Piston Seals Installation.................................................................. WP 0056-13 Figure 19. Seal Assembly Inserter and Remover ............................................................... WP 0056-13 Figure 20. Springs and First Clutch Piston Installation ....................................................... WP 0056-14 Figure 21. Bar and Stud Assembly for Retaining Ring Installation ..................................... WP 0056-14 Figure 22. Bar and Stud Assembly and Compressor Installed for Retaining Ring Installation .................................................................................................. WP 0056-15 Figure 23. First Clutch Pack Installation .............................................................................. WP 0056-17 Figure 24. Backing Plate and Retaining Rings Installation ................................................. WP 0056-18 Figure 25. Range Input Shaft and Center Carrier Assembly Installation ............................ WP 0056-19 Figure 26. Second Clutch Piston Housing Assembly Installation ....................................... WP 0056-20 Figure 27. Retaining Ring Selection and Installation .......................................................... WP 0056-21 Figure 28. Second Clutch Housing Hardware Installation................................................... WP 0056-22 Figure 29. Front Carrier Assembly Installation .................................................................... WP 0056-23 Figure 30. Third Clutch Piston Housing Assembly Hardware Installation ........................... WP 0056-25 Figure 31. Third Clutch Piston Housing Assembly and Retaining Ring Installation............ WP 0056-25 Figure 32. Third Clutch Pack Installation ............................................................................ WP 0056-26 Figure 33. Third Clutch Backing Plate and Pin Installation ................................................. WP 0056-26 Figure 34. Pitot Tubes Installation ....................................................................................... WP 0056-27 Figure 35. Fourth and Reverse Clutch Assembly Installation ............................................. WP 0056-27 Figure 36. Forward Clutch Housing Assembly Installation ................................................. WP 0056-28 Table 1. Retaining Ring Selection ....................................................................................... WP 0056-21 Table 2. Retaining Ring Selection ....................................................................................... WP 0056-24 REPLACE IDLER GEAR ASSEMBLY ............................................................................................. WP 0057 Figure 1. Bearing Retaining Plate Hardware Removal ....................................................... WP 0057-2 Figure 2. Bearing Retaining Plate Removal ........................................................................ WP 0057-2 Figure 3. Hydrostatic Pump Idler Gear Removal ................................................................ WP 0057-3 Figure 4. Hydrostatic Pump Idler Gear Installation ............................................................. WP 0057-4 Figure 5. Bearing Retaining Plate Installation ..................................................................... WP 0057-4 REPLACE BEVEL GEAR ASSEMBLY ............................................................................................ WP 0058 Figure 1. Bevel Gear Assembly Removal ........................................................................... WP 0058-2 Figure 2. Bevel Gear Assembly on Wooden Supports........................................................ WP 0058-3 Figure 3. Bevel Gear Assembly with Multiple-Leg Sling Attached ...................................... WP 0058-4 Figure 4. Bevel Gear Machined Boss Must Align with Pedestal on Center Housing .......... WP 0058-5 Figure 5. Pedestal On Center Housing Must Align with Machined Boss on Bevel Gear Assembly ..................................................................................................... WP 0058-6 Figure 6. Bevel Gear Assembly Installation ........................................................................ WP 0058-6