TM-9-2520-254-34 Direct Support for M113 TX100-1 Transmission 2520-00-066-4240 Download

LEGEND to fig. 5-82. Main sxmtrol valve bolt (9) R4ain control valve lock washer (9 I Maio control valve assembly Regoiator valve retainer screw ( 2 I Retainer screw Inck washer {2) Valve retainer assembly R{egltlator valve spring Chmverter pres.sore regulator valve Valve body bottom cover screw (6) Valve body bottom cover Manual selector valve detent spring MaBIIMal selector valve detent ball Valve body front cover screw (2) Low- to intermediate-range shift valve spring High- to intermediate-range inhibitor valve spring Spring retainer washer (2) Intermediate- to low-range inhibitor valve spring Inhibitor valve (2 I Inhibitor valve dowel pin (2) Inllititor valve body screw Iklhtskor valve body IlllrniMtor valve body screw (41 Inhibitor valve body Iockwasher (4) Extender valve cover screw (3} Extender valve cover screw Extender valve cover In@rmAia@- to high-range shift valve spring Blocker phg 12) Extender valve Extender valve outer spring Extender valve inner spring Extender valve ball Front cover setscrew Valve body front cover Rqulntor valve plug Lmkup shift valve spring Main regulator valve spring Lockup shift valve “l%rottle regulator valve Main regulator valve Front governor valve Control valve body Throttle valve spring 5-49. Cleaning Refer to paragraph 5-2 for cleaning recom- mendations. 5-50. Inspection and Repair Refer to paragraph 5-3 for cleaning recom- mendations. Refer to paragraph 6-3 and table 6-3 for general wear limits information. 5-51. Assembly (fig. 5-82) NOTE All items not covered in a through d below are installed as outlined in paragraph 5-58, steps 43 through 48 (fig. 5-126 through 5- 131). No overhaul (rebuild) of such components is required or recommended. 44 fli 40 47 48 40 30 51 .: ~ >3 .54 5.; .i6 .5 i .58 .; () 60 61 02 63 04 05 ()() 67 68 (,() 70 71 72 73 74 75 76 77 7tf 79 80 81 82 83 tt4 85 Throttle valve M nnoal srhwtor valve 1.<,\v- t{, intermediate-range shift valve IJo\v- to illternlflliate-ratlge shift valve plug 1 ntermediate- to high-range shift valve plug I ntermrdiate- to high-range shift valve Ltwkup shift plug Flo\v valve Trimmer valve secondary spring Trim nwr stop Trimmer valve primary spring Trimmer valve plug Trimmer valve return inner spring Trim mer valve return outer spring Trirpmw valve Rear cover screw [7) Valve body rear cover Rear cover screw ‘1’hrottle valve adjusting screw Throttle valve retainer screw Throttle valve retainer oil transfer plate lockwasher (17) Oil transfer plate bolt (17 I oil transfer plate Iockwasher (3) oil transfer plate bolt (3) Separator plate Manual selector valve detent spring Manual selector valve detent ball Oil transfer plate bolt (2) Lcsckwasher (2 I oil transfer plate assembly Governor pressure check valve retainer Check valve ball oil transfer plate Oil transfer plate slotted spring pin Rear oil pump check valve ball I)rive screw Converter relief valve check ball Retainer washer Converter relief valve spring Converter relief valve retainer Relief valve retainer screw (21 a. Place oil transfer plate (77) on a table, bottom side up, and install ball (81), washer (82), spring (83), and retainer (84). Install two screws (85) in retainer and plate. Tighten screws to 24 to 36 pound-inches torque. b. If drive screw (80) was removed, install new screw. c. If slotted spring pin (78) was removed, install new pin by driving it in place until end projects 0.400 inch from plate surface. d. If retainer (75) and ball (76) were removed, install new parts. Press in until flush, to below flush, with plate surface. 5-41