TM-9-2520-254-34 Direct Support for M113 TX100-1 Transmission 2520-00-066-4240 Download

LEGEND to fig. 5-81. 1 2 3 4 5 (s 7 8 9 10 11 12 13 14 15 16 !7 18 ]$J 20 21 532 23 24 25 26 27 28 2[} 30 31 32 33 Bolt Flat washer Speedometer drive plug Plug gasket Transmission housing assembly Spmdometer bushing Shift lever sleeve Transmission housing Power takeoff cover gasket Power takeoff cover Cover bolt [61 Cover bolt washer (6 I Rear pitot tube washer (2) Spwdometer drive gear Output flange bearing Bearing retainer snap ring Output flange oil seal Output flange assembly Transmission output flange Output flange retainer washer Flange bolt Flange bolt lock tab Fkmge bolt seal ring Rear pitot tube self-locking bolt Rear governor pressure check plug Throttle valve control shaft assembly Con&ol shaft seal ring Manual control selector shaft assembly Selector shaft seal ring Ancl]or pin (2) Transmimion name plate Transmimion name plate drive screw (4) Selector Anft snap ring 5-44. Cleaning Refer to paragraph 5-2 for cleaning recom- mendations. 5-45. Inspection and Repair Refer to paragraph 5-3 for general inspection and repair recommendations. Refer to paragraph 6-3 and table 6-3 for general wear limits information. 5-46. Assembly (fig. 5-81) NOTE All items not covered in a and b below are installed as outlined in paragraph 5-58, 34 35 36 37 38 39 40 41 42 43 44 45 40 47 48 49 50 51 52 53 54 55 56 57 Throttle valve shaft snap ring Oil transfer tube O-type seal ring Oil transfer tube Tube retainer ring (6) Tube seal ring (6) Oil transfer tube (6) Oil transfer tube O-type seal ring Main pressure check plug Lockup pressure check plug Power takeoff cover gasket l’ower takeoff cover Cover bolt plain washer (6) Cover bolt (6 I Oil suction tube seal ring (2) Oil filter can Lockwasher (3) Bolt (3) Oil pan gasket Transmission oil pan Oil pan self-locking bolt (26) Plain nut Drain plug gasket Oil drain plug Oil filter element retainer !38 Oil filter spring 59 Oil filter cover assembly 60 Oil filter strap bolt 61 Oil filter strap 62 Oil filter parts kit 62.1 Oil filter seal ring 62.2 Oil filter seal ring 62.3 Oil filter element assembly steps 2 through 5 (fig. 5-84 through 5-87). No overhaul (rebuild) of such components is required or recommended. a. If speedometer bushing (6) was removed, insert new bushing in bore, and drive in until outer end is flush with bore face. b. If shift lever sleeve was removed, insert new sleeve in bore, and drive from outside in until head is seated firmly against bore face. NOTE Outer end of sleeve has a very slightly larger diameter. Section XI. OVERHAUL (REBUILD) OF OIL TRANSFER PLATE ASSEMBLY 5-47. Description a. Do not remove governor pressure check valve Refer to paragraph 2-11 for description of the oil retainer (75) and ball (76) unless replacement is transfer plate assembly. necessary. 5-48. Disassembly b. Do not remove slotted spring pin (78) unless (fig. 5-82 replacement is necessary. NOTE c. Do not remove drive screw (80) unless All items not covered in a through d below replacement is necessary. were removed from the transmission as d. Remove two converter relief valve retainer outlined in paragraph 5-6, steps 8 through screws (85), and remove retainer (84), spring (83), 13 (fig. 5-8 through 5-13). No further washer (82), and ball (81) from oil transfer plate disassembly of those parts is required. (77). 5-39