TM-9-2320-280-34 HMMWV Direct Support & General Support Maintenance Manual Download
Page 548 of 1258
1. Inspect rack piston (7) for breaks, burrs, chipped seal grooves (8), crossed or stripped threads, cracked or broken gear teeth (3), and broken, chipped or scored internal worm thread. Repair minor burrs and scoring with fine mill file or crocus cloth. Repair minor thread damage. Replace rack piston (7) if gear teeth (3) are cracked or broken or other damage is unrepairable. 2. Inspect twenty-four ball bearings (6) for breaks, chipped surface, flats, and scoring. Minor scoring on ball bearings (6) is acceptable. Replace ball bearings (6) as a set if any one or more fails inspection. (Refer to note above.) 3. Inspect ball bearing guides (2) for bends, dents, and breaks and clamp (5) for bends and breaks. Replace damaged parts. 4. Inspect screw-assembled washers (4) for crossed or stripped threads. Replace screw-assembled washers (4) if damaged. 5. Inspect rack piston plug (1) for burred or rounded hex flats and stripped or crossed threads. Replace rack piston plug (1) if damaged. 1. Inspect valve body (16) for burrs, chipped or broken seal ring grooves (15), scoring on inner bore (17), and wear. Repair minor burrs and scoring with crocus cloth. Valve body (16) bore (17) maximum I.D. is 1.1557 in. (29.355 mm) and valve body (16) minimum O.D. (14) is 2.0150 in. (51.181 mm). Replace valve body (16) if worn or unrepairable. 2. Inspect valve (13) for burrs, cracks, blocked oil passages (18), chipped or cracked seal ring groove, scoring, and wear. Spool valve (13) minimum O.D. (12) is 1.152 in. (29.26 mm). Remove minor burrs and scoring with crocus cloth and clear blocked oil passages (18). Replace valve (13) if worn or unrepairable. 3. Inspect stub shaft (9) for bends, cracks, breaks, damaged pin (12), bent or twisted splines (11), and worn bearing journal (10). Bearing journal (10) minimum O.D. is 1.25 in. (31.75 mm). Replace stub shaft (9) if worn or damaged. 4. Inspect worm (19) for bends, breaks, burrs, chipped thread (20), and scoring. Remove minor burrs and scoring with fine mill file or crocus cloth. Replace worm (19) if damage is unrepairable. (Refer to note before step e.1.) 5. Inspect adjuster plug (21) for cracks, breaks, crossed or stripped threads, chipped retainer grooves, and seal ring surface. Replace plug (21) if damaged. 6. Inspect adjuster plug needle bearing (22) for damage (TM 9-214) and wear. Replace needle bearing (22) if damaged or I.D. worn over 1.25 in. (31.75 mm). If damaged or worn, replace needle bearing (22) as follows. a. Using adjuster plug bearing remover/installer, remove bearing (22) from adjuster plug (21). b. Lubricate adjuster plug (21) and bearing (22) with hydraulic fluid. c. Using adjuster plug bearing remover/installer, install bearing (22) 0.625 in.(16 mm) deep in adjuster plug (21). 7. Inspect adjuster plug locknut (23) for cracks, burred flats or notches, and stripped or crossed threads. Replace locknut (23) if damaged. 8. Inspect bearing retainer (24), thrust bearing spacer (25), small race (26), upper thrust bearing (27), and large race (28) for damage (TM 9-214). Replace all items if one item is damaged. 9. Inspect lower thrust bearing (30) and two races (29) for damage (TM 9-214). Replace all items if any one is damaged. NOTE Outer edge of bearing is marked with identification number. f. Valve and Adjuster Group Inspection and Repair 11-5. STEERING GEAR REPAIR (Cont'd) e. Rack Piston Group Inspection and Repair NOTE If rack piston internal worm thread, worm thread, or ball bearings are broken, chipped, or moderately or badly scored, replace all three parts. TM 9-2320-280-34 11-16 Change 1