TM-9-2815-220-34P Parts Manual and Special Tools for AVDS-1790-2CA, AVDS-1790-2DA and AVDS-1790-2DR engines Download
Page 10 of 415
SECTION I TM9-2815-220-34P (5) Part numbers for bulk materials are referenced in this column in the line item entry for the item to be manufactured/fabricated. (6) When the item is not used with all serial numbers of the same model, the effective serial numbers are shown on the last line(s) of the description (before UOC). Not applicable. (7) The usable on code, when applicable (see paragraph 5, Special information). (8) In the Special Tools List section, the basis of issue (BOI) appears as the last line(s) in the entry for each special tool, special TMDE and other special support equipment. When density of equipments supported exceeds density spread indicated in the basis of issue, the total authorization is increased proportionately. (9) The statement “END OF FIGURE” appears just below the last item description in Column 5 for a given figure in both Section II and Section Ill. f. QTY (Column (6)). The QTY (quantity per figure column) indicates the quantity of the item used in the breakout shown on the illustration figure, which is prepared for a functional group, subfunctional group or an assembly. A “V” appearing in this column in lieu of a quantity indicates that the quantity is variable and the quantity may vary from application to application. 4. Explanation of Columns (Section IV). a. NATIONAL STOCK NUMBER (NSN) INDEX. (1) STOCK NUMBER column. This column lists the NSN by National item identification number (NIIN) sequence. The NIIN consists of the last nine NSN digits of the NSN (i.e., 5305-01-674-1467) NIIN When using this column to locate an item, ignore the first 4 digits of the NSN. However, the complete NSN should be used when ordering items by stock number. (2) FIG. column. This column lists the number of the Figure where the item is identified/located. The figures are in numerical order in Section II and Section Ill. (3) ITEM column. The item number identifies the item associated with the figure listed in the adjacent FIG. column. This item is also identified by the NSN listed on the same line. b. PART NUMBER INDEX. Part numbers in this index are listed by part number in ascending alphanumeric sequence (i.e., vertical arrangement of letter and number combination which places the first Ietter or digit of each group in order A through Z, followed by the numbers 0 through 9 and each following letter or digit in like order.) (1) CAGEC column. The Commercial And Government Entity (CAGE) Code (C) is a 5 digit alphanumeric code used to identify the manufacturer, distributor or Government agency, etc., that supplies the item. (2) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm, corporation or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications standards, and inspection requirements to identify an item or range of items. (3) STOCK NUMBER column. This column lists the NSN for the associated part number and manufacturer identified in the PART NUMBER and CAGEC columns to the left. (4) FIG. column. This column Iists the number of the figure where the item is identified/located in Section II and Ill. (5) ITEM column. The item number is that number assigned to the item as it appears in the figure referenced in the adjacent figure number column. c. FIGURE AND ITEM NUMBER INDEX. (1) FIG. column. This column lists the number of the figure where the item is identified/located in Section II and Ill. (2) ITEM column. The item number is that number assigned to the item as it appears in the figure referenced in the adjacent figure number column. (3) STOCK NUMBER column. This column lists the NSN for the item. (4) CAGEC column. The Commercial And Government Entity (CAGE) Code (C) is a 5 digit alphanumeric code used to identify the manufacturer, distributor or Government agency, etc., that supplies the item. (5) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm, corporation or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications standards and inspection requirements to identify an item or range of items. 4