TM-9-2815-220-34 Direct Support Manual for AVDS-1790-2C and AVDS-1790-2D Engines Download
Page 171 of 532
Figure 2-145. Remoit1g or i11J//i11g generator coble and wiring l1ar11eu bracket . I (b) Position assembled mounting bracket (fig. 2-144) over the first four mounting holes immeiately to the rear of the Ufting eye whkh extends through the righl front upper cover. Secure the bracket to the cover wHh four ca screws and lockwashers. Install two retaining straps on generator cable and wiring haess and secure to bracket assembly with four capscrews and lock- washers. (c) Install bracket assembly (fig. 2-143) and secure to oil cooler frame with two capscrews and self-locking nuts. Install two retaining straps and secure one to each bracket assembly with two cap· screws and lockwashers. Install manifold preheat cable connector. (c.1) Position loop clamp (fig. 2-142.l) o n spacer and secure with lockwasher and machine boll. (d) Instl loop clamp (fig. 2-142) on generator cable and secure to crankcase with capscrew and lockwasher. Install loop clamp on generator cable and wiring harness and secure to crankcase with capscrew and self-lockbtg nut. Secure wiring haess ground terminal Jug to crankcase with capscrew and lockwasher. ( e) Cl ean electrical lead (ground) terminals. Install one flat washer in the generator support upper counterbore (fig. 2-17. l ). Secure the inner lead with one flat washer and capscrew. Remove lower right generator support capscrew and flat washer. Discard capscrew. Install existing flat washer in the generator support counterbore. TM 9-2815-220-34 Secure outer lead with one flat washer and new capscrew (3/8-24 x 1-3/4 long). Torque tighten capscrews to 275 pound inches. Install assembled ground strap and bliss bar on generator terminal and secure with self-locking nut and flat washer (7, fig. 2-14 J). Install assembled generator cable ( 6) on generator terminal and secure with self-locking nu l and flat washer (5). Install transmission cable connector (4) in bracket and secure with follr machine screws, lockwashcrs and hexagon nuts (3). Install generator cable connector (2) and ( 1 ). Install two loop clamps (6, fig. 2-140) and secure to crankcase and damper housing with two capscrews and loekwashers (6). Install two brackets (4) and secure to oil pan with two capscrews and lk- washers (3). Install two lꝏp clamps (2) on wiring har- ness and secure to brackets with two capscrews, lk- washers and hexagon nuts (1). Install lꝏp clamp (9) on wiring harness and secure to oil pressure regulator valve stud with self-lking nut (8). Install hour meter cable connector (7). Install low oil pressure (13) oil temperature (12) oil pressure (11) and high oil . temperature (10) cable electrical connector shells. ) Install bracket (fig. 2-139) and secure to oil pan with capscrew and lockwasher. Install lꝏp clamp on wiring harness and secure to bracket with capscrew, lkwasher and hexagon nut. Install two loop clamps and secure to crankcase with two cap- screws and lockwashers. Install fuel/water separator cable connector. () Install fuel shut-off cable connector (fig. 2- 138) and fuel solenoid cable connector. Install lꝏp clamp on fuel shut-off cable and secure to damper housing with machine screw and lockwasher. (i) Install the assembled starter cable mount- ing bracket (f i g. 2-137) and secure to left front upper cover with four capscrews and lockwashers. Install retaining strap on starter cables and secure to bracket assembly with two capscrews and lk- washers. (il) On late engines install the assembled starter cable mounting bracket and loop clamp (fig. 2-136.3) and secure with two capscrews and three assembled washer bolts. Secure starter low voltage protective modu.le and ground lead to bracket with two capscrews and lockwashers. ·Con nect wiring harness to . module. . (i.2) Secure ound Jcad to bracket with capscrew and lockwasher (fig. 2-J 36.2). Connect two electrical connectors to solenoid valves. Secure loop clamp (fig. 2-136.2) with self-locking nut. Secure two electrical lead Joop clamps (fig. 2-136.1) to upper cover with two assembled washer bolts. Install loop clamp to t11e sMe of oil cooler support frame with assembled washer bolt. Change 3 2-89