NMWR-9-2815-220 Overhaul Manual for M60 M88 Engine AVDS-1790-2CA, AVDS-1790-2DA, AVDS-1790-2DR Download
Page 695 of 1014
NMWR 9-2815-220 DUST EJECTOR SYSTEM (MODELS AVDS-1790-2CA AND AVDS-1790-2DA) OVERHAUL 0036 00 THIS WORK PACKAGE COVERS: General Instruction, Disassembly, Cleaning, Inspection, Repair, and Assembly INITIAL SETUP: Materials/Parts Materials/Parts – Continued Air duct hose (2) (item 39, WP 0052 00) Machine bolt (2) (item 456, WP 0052 00) Air duct hose (2) (item 311, WP 0052 00 Machine bolt (2) (item 475, WP 0052 00) Assembled washer screw (1) (item 270, Machine bolt (7) (item 481, WP 0052 00) WP 0052 00) Machine screw (22) (item 266, WP 0052 00) Assembled washer screw (4) (item 271, Nut (22) (item 706, WP 0052 00) WP 0052 00) Left bank inner insulation sleeving (1) (item 228, Elbow (1) (item 734, WP 0052 00) WP 0052 00) Gasket (2) (item 223, WP 0052 00) Left outer insulation (1) (item 227, WP 0052 00) Gasket (2) (item 240, WP 0052 00) Self-locking nut (5) (item 589, WP 0052 00) Hose (2) (item 226, WP 0052 00) Self-locking nut (12) (item 812, WP 0052 00) Hose (2) (item 232, WP 0052 00) Tube (1) (item 224, WP 0052 00) Hose clamp (2) (item 2, WP 0052 00) Washer (44) (item 547, WP 0052 00 Hose clamp (12) (item 517, WP 0052 00 Washer (1) (item 798, WP 0052 00) Right bank inner insulation sleeving (1) (item 230, WP 0052 00) Tools Right bank outer insulation (1) (item 229, Tool kit, general mechanic's: automotive WP 0052 00) (item 30, WP 0051 00) Lockwasher (22) (item 689, WP 0052 00) Lockwasher (2) (item 694, WP 0052 00) References Lockwasher (2) (item 695, WP 0052 00) TM 9-2815-220-34 Loop clamp (2) (item 225, WP 0052 00) WP 0005 00 Loop clamp (2) (item 234, WP 0052 00) Loop clamp (1) (item 614, WP 0052 00) GENERAL INSTRUCTION 1. This section covers overhaul of the dust ejector and associated parts comprising part of the clean air package on Models AVDS-1790-2CA and AVDS-1790-2DA. Specific instructions on disassembly, cleaning, inspection, repair, and assembly are included. Wear limits, fits, tolerances, and overhaul inspection procedures (OIPs) for individual components are also included. Mandatory replacement parts are designated by an asterisk (*) in the key to Figure 1. DISASSEMBLY 1. Disassemble dust ejector and associated parts in accordance with TM 9-2815-220-34. CLEANING 1. Refer to WP 0005 00 for general cleaning instructions. 0036 00-1