NMWR-9-2815-220 Overhaul Manual for M60 M88 Engine AVDS-1790-2CA, AVDS-1790-2DA, AVDS-1790-2DR Download
Page 301 of 1014
NMWR 9-2815-220 CAMSHAFT AND DRIVE ASSEMBLIES OVERHAUL 0016 00 THIS WORK PACKAGE COVERS: General Instruction, Disassembly, Cleaning, Inspection, Reclamation, Repair, and Assembly INITIAL SETUP: Materials/Parts Materials/Parts Cloth, crocus (item 2, WP 0050 00) Retaining ring (2) (item 556, WP 0052 00) Compound, cleaning (item 1, WP 0050 00) Seal (1) (item 277, WP 0052 00) Steel grit (item 10, WP 0050 00) Self-locking nut (8) (item 525, WP 0052 00) Air duct hose (2) (item 39, WP 0052 00) Sleeve bearing (1) (item 367, WP 0052 00) Cap screw (6) (item 483, WP 0052 00) Speedometer adapter (1) (item 521, WP 0052 00) Cap screw (1) (item 506, WP 0052 00) Washer (8) (item 361, WP 0052 00) Cap screw (6) (item 784, WP 0052 00) Washer (4) (item 464, WP 0052 00) Cap screw (60) (item 789, WP 0052 00) Washer (7) (item 465, WP 0052 00) Cap screw (6) (item 790, WP 0052 00) Washer (16) (item 804, WP 0052 00) Gasket (2) (item 1, WP 0052 00) Gasket (2) (item 293, WP 0052 00) Tools Gasket (2) (item 297, WP 0052 00) Tool kit, general mechanic's: automotive Hose clamp (3) (item 3, WP 0052 00) (item 30, WP 0051 00) Intercylinder sleeve (10) (item 177, WP 0052 00) Dial indicator (item 19, WP 0051 00) Lockwasher (7) (item 697, WP 0052 00) Lathe (item 20, WP 0051 00) Lockwasher (4) (item 695, WP 0052 00) Milling machine (item 22, WP 0051 00) Machine bolt (16) (item 448, WP 0054 00) Spray gun (item 28, WP 0051 00) Machine bolt (4) (item 475, WP 0052 00) Machine bolt (3) (item 774, WP 0052 00) References Nonelectrical wire (V) (item 577, WP 0052 00) TM 9-2815-220-34 O-ring (2) (item 468, WP 0052 00) MIL-STD-1687A(1) O-ring (1) (item 652, WP 0052 00) WP 0005 00 O-ring (2) (item 653, WP 0052 00) O-ring (2) (item 660, WP 0052 00) 0016 00-1 Change 1 GENERAL INSTRUCTION This section covers overhaul of the camshaft and drive assemblies. Specific instructions on disassembly, cleaning, inspection, reclamation, repair, and assembly are included. Wear limits, fits, tolerances, and overhaul inspection procedures (OIP’s) for individual components are also included. Stud identification information is included in the repair instructions. Mandatory replacement parts are designated by an asterisk (*) in the key to Figures 5 and 6. DISASSEMBLY Remove camshaft and disassemble drive assemblies in accordance with TM 9-2815-220-34.